Halsey Taylor HRFSER, HRFER, HRFSR, HRFESR Owners Manual

HRFERQ*C HRFSRQ*C HRFSERQ*C HRFESRQ*C

Owners Manual

Contour™ Series Water Coolers

Refrigerated Fountains with Back Panel

Figure 1 – HRFSER

Figure

1

2

3

Not Shown

Model

HRFSER

HRFER

HRFSR

HRFESR

Figure 2 – HRFER Figure 3 – HRFSR

Description

ContourTM Series - Dual Installation

ContourTM Series - Extended Reach

ContourTM Series - Standard Reach

ContourTM Series - Dual Reversed Installation

INSTALLER

Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes.

When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.

Service to be performed by authorized service personnel only.

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices

to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which results in an “electrolysis” effect occurring in the fountain. This may result in water which has a metallic taste to it or has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the

installation, and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation.

Any drain ttings provided by the installer should be made of plastic which will electronically isolate the fountain from the remainder of the building’s plumbing circuits.

1

97800C - (Rev. K - 06/16)

HRFERQ*C HRFSRQ*C HRFSERQ*C HRFESRQ*C

1/4” O.D. TUBE

WATER INLET

TO COOLER

NOTE: WATER FLOW

3/8” O.D. UNPLATED COP-

PER TUBE CONNECT

COLD WATER SUPPLY

DIRECTION

SERVICE STOP

(NOT FURNISHED)

Figure 4 – Water Supply Connections

Item Part No. Description

Drain

Kit - Retaining Nut (5 Pack)

Strainer & Ferrule Assy

Kit - Bubbler/Nipple/Gasket Assy

Push Button

Push Button Sleeve

Regulator Holder

Edge Trim - 2FT

Regulator

Cap screw

Screw - #10-24 X .50” PHTC

Strainer (Supplied with Chiller)

Fountain Arm-Short

Fountain Arm-Extended

Bottom Cover Plate-Short

Bottom Cover Plate-Extended

Back Panel HRF-SER

Back Panel HRF-ESR

Back Panel HRF-ER

Back Panel HRF-SR

Kit - Hex Nut (4 Pack)

Poly Tubing - 1/4 (Cut To Length)

Bracket-Regulator Mounting

Lower Panel HRF-SER/ESR

Lower Panel HRF-ER/SR

Kit - Union-1/4” (3 Pack)

Kit - Tee-1/4” (3 Pack)

10

11

12

13

14

15

16

17

18

19

20

21

1

2

3

4

5

6

7

8

9

LK464

1000002027

45336C

98533C

45662C

45663C

50986C

56369C

61313C

75672C

112627543890

55996C

28782C

28783C

55000661

55000665

26839C

27028C

26837C

26835C

1000001926

56092C

28823C

27026C

26833C

1000002162

1000001994

BUILDING WATER INLET

Parts List

Installation Package

The components for installation are packed in three separate boxes, regardless of the type of unit being installed. The boxes contain the following:

Box No. 1: Wall Frame(s) Box No. 2: Remote Chiller, SJ8 Box No. 3: Fountain(s), Arm(s) and Panels

Additional materials, as noted in the Parts List, are also shipped in these boxes.

Number Required

HRFER

1

7

1

-

1

-

1

-

1

-

3

1

-

1

HRFSR

1

5

1

-

1

-

1

3

1

-

1

HRFSER

2

12

1

-

6

1

2

1

-

1

HRFESR

12

See Fig.

2

1

-

1

-

6

1

2

1

-

1

18

17

18

17

18

17

18

4, 15, 19

18

12, 13, 18

18

12, 13, 18

17

18

17

14, 18

19

15

97800C - (Rev. K - 06/16)

2

HRFERQ*C HRFSRQ*C HRFSERQ*C HRFESRQ*C

Models

HRFSER & HRFESR

1. Cut a rectangular wall opening 37-1/2” (953 mm) W x 37-3/4” (959 mm) H and 4-1/2” (114 mm) above the

oor line (see Figure 6). The dimensions are required

to obtain proper rim and bubbler heights for compliance with ANSI standard A117.1.

2. Reinforce the wall opening on all sides to adequately support the water fountain. This reinforcement must support up to 150 lbs. static load and provide a means for securing the frame assembly in place.

NOTE: Building construction must allow for adequate

air ow on both sides, top and back of chiller.

A minimum of 4” (102 mm) on both sides and

top is required. See chiller installation for

additional instructions.

3. Install plumbing and electrical rough-ins. A junction box for a (3) wire, 10 amp branch circuit is provided on the inside of the chiller. (Standard 120 Volts, 60 Hz, and single phase.)

Figure 5 – HRFSER Rough-In

REVERSED CONFIGURATION:

HIGHER UNIT ON THE RIGHT

4. Remove frames and related hardware from packaging. Release the two shelf rods by cutting cable ties. Attach the two frames together through the upright supports with (4) 5/16” x 3/4” (19 mm) long bolts and nuts (provided). Tighten securely.

MAKE SURE FRAME CONFIGURATION

MATCHES THE COOLER TO BE INSTALLED

STANDARD CONFIGURATION

HIGHER UNIT ON THE LEFT

Figure 6 – Rough-In Assembly Dual-Station Mounting Frames

3

97800C - (Rev. K - 06/16)