Halsey Taylor HRFG-EBP, HRFG-SBP Owner's Manual

HRFGEBP_A, HRFGSBP_A

Halsey Taylor Owners Manual

Non-Refrigerated Marblyte Fountain

with Back Panel

Installer

To assure you install this model easily and correctly, PLEASE
READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING
THE INSTALLATION. CHECK YOUR INSTALLATION FOR
COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER
APPLICABLE CODES. After installation, leave these instruc­tions inside the fountain for future reference.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.

97715C (Rev. B - 5/04)

97715C (Rev. B - 5/04)

PAGE 2

HRFG-EBP, HRFG-SBP ROUGH-IN

MARBLYTE BACK PANEL

FIG. 1

DETAIL 1

HRFGEBP_A, HRFGSBP_A

FINISHED FLOOR

LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN
C = MOUNTING HOLES FOR SECURING FOUNTAIN TO WALL

HRFGEBP_A, HRFGSBP_A

INSTALLATION INSTRUCTIONS

MARBLYTE BACK PANEL

1. Wall should already be framed for the fountain using the positioning dimensions shown in Fig. 1.
Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight).

2. Install rough-in plumbing as shown in Fig. 1. Run supply water inlet line and connect to a
service stop (not provided). Turn on supply water and flush thoroughly. Close water supply.

3. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back
panel and wall using (4) 5/16" bolts and washers (not provided). Bolts should be long enough to securely
fasten the fountain to the wall. Tighten securely, but do not over tighten. Over tightening will crack the
Marblyte Fountain.

4. Remove elbow from end of p-trap (item 1) and attach it to drain tube. Re-attach elbow to p-trap and
cut waste tube to required length using plumbing hadware and trap as guide.

5. Make water supply connections from service stop to the fountain strainer (item 16) by inserting the
water inlet line into the inlet side of strainer until it reaches a positive stop about 3/4", (See Figure 6,
Page 7). Turn on water supply and check for leaks. Newly installed water supply line should be
insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER

AS DAMAGE TO THE O-RINGS MAY RESULT.

6. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is
above 105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by
reason of connecting these products to supply line pressure lower than 20 PSIG or higher than 105 PSIG
is not covered by warranty.

7. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure
varies greatly from this, remove items 8 & 12 (See Figure 3, Page 6) by loosening set screw (item 15)
and adjust the screw on regulator (item 14). Clockwise adjustment will raise stream height and counter­ clockwise adjustment will lower stream height. For best adjustment stream height should be approxi­ mately 1-1/2" (38mm) above the bubbler guard (See Figure 7, Page 7).

8. Replace bottom access panel to fountain basin using screws provided. Tighten securely.

Care and Maintenance of Halsey Taylor Marblyte Fountains

Marblyte provides an exremely durable, nonporous surface which resists staining. Care is very simple.
Routine cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam cleaner, is all that is
normally needed to give many years of trouble free service. Cleaners left standing on the fountain surface
can dull the surface finish. Be certain to rinse all cleaning agents completely and polish with a soft cloth.

Harsh abrasive cleaners are not required and should not be used.

Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple
scratches and stains. Cigarette burns can normally be removed without noticeable effect. Deeper
scratches or gouges can be corrected with fine grit sandpaper (240 grit then 400 grit) or a green Scotchbrite
pad.

To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or like
products will keep the finish looking like new.

PAGE 3

97715C (Rev. B - 5/04)