Halsey Taylor Hose Bib Kits User Manual

E24 / 8-2007
Hose Bib Kits
Hose Bib Kit
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
halseytaylor.com
Locking Hose
Bib Kit
GENERAL
Panel has Evergreen textured powder coat finish and E-Coat immersion for year-round beauty with minimum maintenance. The E-Coat immersion process coats the outside and inside of the panel for the ultimate in corrosion protection.
This accessory is designed to replace the existing access cover on units in the Endura II
Tubular Pedestal Fountain series. It is not designed for sub-freezing applications.
Locking Hose Bib kit includes panel and a door that can be secured with a standard padlock (not included).
Water inlet is 1/2" tubing (provided).
Hose bib shown on model 4400 Endura II
pedestal fountain
Locking Hose Bib Kit (open)
When ordering use part #: 97887C (non-locking hose bib)
97889C (locking hose bib)
Shipping Weight: 5.5 lbs. (non-locking hose bib) Shipping Weight: 8.5 lbs. (locking hose bib)
NOTE: Continued product improvement makes specifications subject to change without notice. See Halsey Taylor website for most current spec sheet.
JOB NAME:
ENGINEER/CONTRACTOR NAME:
APPROVAL:
DATE:
Printed in the U.S.A.
INSTALLATION INSTRUCTIONS
1. Shut off water supply to fountain.
2. Determine location for installation of Hose Bib Accessory. Remove existing access cover plate. (This accessory is designed to replace the existing access cover).
3. Disconnect the fountain water line from the main water supply. Connect Tube (Item 8) to existing fountain strainer as shown below.
4. Connect Tee (Item 6) to Tube (Item 8). Connect main water supply to Tee using 1/2" Copper Tube (Item 9). DO NOT TURN MAIN WATER SUPPLY
ON AT THIS TIME!
5. Connect Hose Bib Accessory water line to the Tee and to the Elbow (Item 5) on the Access Panel (Item 3) using 1/2" Copper Tube (Item 7) as shown below, maintain loop in coil to facilitate installation and removal of Access Panel.
6. Turn on main water supply. Check for leaks. If there are leaks, turn off main water supply and correct the water leaks as required. After insuring that all connections are leak free, leave main water supply on and replace any panels that may have been removed in the installation process.
7. Assemble Hose Bib Accessory to the main fountain body.
PARTS LIST
ITEM NO. PART NO. DESCRIPTION
1 75624C Fitting - Hose Vacuum Breaker
2 75619C Faucet - 1/2" NPT
3 45753C Panel - Access w/Bib Recess
4 70977C Nut - Lock 1/2" Conduit
5 70972C Elbow - 90° x 1/2" MPT
6 75623C Fitting - Tee 1/2" x 1/2" x 3/8"
7 66555C Tube - 1/2" O.D. x 36.00" Lg.
8 66475C Tube - 3/8" O.D. Tee to Strainer
9 66641C Tube - 1/2" O.D. x 4.38" Lg.
10 75521C Bit - Pinned Torx T-27 (NS)
11 75535C Screw - 1/4-20 x 3/4" Torx
12 45802C Panel - Locking Hose Bib
13 45804C Door - Locking Hose Bib
Hose Bib Kits
Loading...