Halsey Taylor HAC-HB-NF1A, HTHB-HAC-NF Installation Manual
HAC-HB-NF_1A
Installation/Care/Use Manual
HTHB-HAC-NF
Retrofit Hydroboost Bottle Filling St ation
IMPORTANT
THIS IS AN INDOOR APPLICATION ONL Y .
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSON.
TOOLS REQUIRED
BUT NOT PROVIDED:
SAFETY GLASSES
GLOVES
ELECTRIC DRILL
3/4” WRENCH OR CRECENT WRENCH
UTILITY KNIFE
T APE MEASURE
PENCIL
5/32” ALLEN WRENCH
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WA TER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y OCCUR A WA Y FROM THE
BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNT AIN, CREA TING AN ELECTROL YSIS WHICH CAUSES A MET ALLIC T ASTE OR AN INCREASE IN THE METAL CONTENT OF THE WA TER.
THIS CONDITION IS A VOIDABLE BY USING THE PROPER MA TERIALS AS INDICA TED. ANY DRAIN FITTINGS
PROVIDED BY THE INST ALLER SHOULD BE MADE OF PLASTIC T O ELECTRICALLY ISOLA TE THE FOUNT AIN
FROM THE BUILDING PLUMBING SYSTEM. WE SUGGEST THA T THE BOTTLE FILLING ST A TION AND W A TER
COOLER BE PROTECTED BY A GROUND F AUL T CIRCUIT INTERRUPTER (GFCI).
INSTALLER
HTHB-HAC-NF Bottle Fillers are among the easiest to install on the market today.
To insure you install these models easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK
YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND
OTHER APPLICABLE CODES. After installation, leave these instructions with the
Fountain for future reference.
Page 1 98709C (Rev. A - 3/11)
NOTE:
HAC-HB-NF*1A
WATER COOLER PREPARATION
• On T wo Level Models, the Bottle Filling Unit MUST be mounted on the higher unit:
• Two Level S tandard Models; high unit is on Lef t Hand(LH) side.
• Two Level Reverse Models; high unit is on Right Hand(RH) side.
1) Remove Front Panel
• Remove lower front panel of water cooler by
removing the four (4) screws, two at top
and two at bottom. On T wo Level Models,
remove both front panels.
• W ARNING: Before proceeding.
Disconnect electrical power supplying the water
cooler . Switch circuit breaker “OFF” or remove
fuse.
• Unplug water cooler power cord from electrical
outlet.
• Shut of f water supply .
Remove Front Panel
Loosen Drain Line
2) Loosen Drain Line
•
Loosen Slip-Joint Nut at P-trap.
•
Note: Have container/bucket readily available to
catch water from lines.
3) Remove Basin Fasteners
Remove Basin Assembly by loosening eight (8)
screws, four on each side of basin.
Remove Basin Fasteners
Page 298709C (Rev. A - 3/11)
WATER COOLER PREPARATION
4) Remove Bubbler Water Line
Disconnect water line from bubbler.
HAC-HB-NF_1A
5) Lift and Remove Basin.
Remove basin assembly by lifting straight
up, disconnecting the drain line from
the P-trap.
5) Exchange Drain hardware.
• Remove drain hardware from original basin.
• Verify that the rubber washers are also
removed for reuse.
• Remove the drain tube from the elbow.
• Shorten the horizontal length of the
drain tube by 7/8”.
• Re-attach the drain tube to the elbow.
• Remove the protective covering from the
basin.
• Attach the drain hardware onto the new
basin ensuring drain is positioned exactly
as original.
7) Exchange Bubbler hardware.
••
• Remove bubbler hardware from original
••
basin.
••
• V erify that the rubber washers are also
••
removed for reuse.
••
• Reinstall the bubbler hardware on to the
••
new basin.
••
• Ensure the bubbler is properly positioned
••
with the stream falling onto the center of
splash ridge.
Remove Bubbler Water Line
Lift and Remove Basin.
Exchange Drain hardware.
Exchange Bubbler hardware.
Page 3 98709C (Rev. A - 3/11)
Loading...