Halsey Taylor 98030C User Manual
E14 / 8-2007
Vandal-Resistant Kits
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
halseytaylor.com
98030C KIT
GENERAL
This kit contains a sufficient quantity of pieces
for field modification of Halsey Taylor drinking
fountains and water coolers to make units
more tamper-resistant. For: HTV, HAC, HT, HRF,
WC, WM, SW, SCWT, and OVL series single
basin units. Refer to service manual for
detailed instructions specific to each series.
For general installation instructions see back of this
spec sheet.
KIT CONSISTS OF:
■
Chrome plated heavy duty unleaded brass
vandal-resistant bubbler
■
2 Vandal-resistant lock washers
■
1 Bubbler nipple
■
30 Vandal-resistant screws
■
2 Drive bits
Use part #98030C when ordering.
09855 KIT
GENERAL
This kit will modify units to make them more
vandal-resistant by replacing existing drain
plug with vandal-resistant version. Will fit all
units with 2-7/8" drain opening. For general
installation instructions see back of this spec
sheet.
KIT CONSISTS OF:
■
Drain plug tapped and drilled for allen-head
screw (included)
■
Strainer plate
Use part #60-09855-51-640 when ordering.
98032C KIT
GENERAL
This kit will modify units to make them more
vandal-resistant by replacing existing drain
plug with vandal-resistant version. Will fit HRF
series units with 1-3/8" drain opening. For
general installation instructions see back of this
spec sheet.
KIT CONSISTS OF:
■
One-piece drain
■
Gasket
Use part #98032C when ordering.
75520C/75523C (not pictured)
GENERAL
Vandal-resistant pinned Torx®bits used for
removing fasteners on vandal-resistant units.
■
75520C - bit T25
■
75523C - bit T20
Note: Continued product improvement makes
specifications subject to change without notice.
See Halsey Taylor website for most current
spec sheet.
09855
Universal
Vandal-Resistant Kit
Vandal-Resistant
Drain Kit
98030C
Vandal-Resistant
Small Drain Kit
98032C
JOB NAME:
ENGINEER/CONTRACTOR NAME:
APPROVAL:
DATE:
Printed in the U.S.A.
Remove snap-in strainer from unit and replace existing
drain plug with vandal-resistant drain plug and strainer.
Secure with cap screw.
Installation Instructions
For 09855
Vandal-Resistant Drain Kit
Installation Instructions
For 9032C Vandal-Resistant
Small Drain Kit
1. Remove fountain or cooler panel to gain access to the bubbler
fitting from underneath the basin.
2. Remove existing bubbler from the unit. Hold the bubbler fitting
on the underside of the basin and unscrew bubbler from the
top of the basin.
3. If the bubbler nipple is plastic, replace with the new metal
bubbler nipple (Item 5) by removing the tube from the quick
connect fitting and reinserting the tube approximately 3/4" in
the metal nipple.
4. Remove and discard the sealing gaskets (black rubber washers)
from above and below the basin. Reinsert the bubbler fitting
into the basin.
5. Assemble the two lockwashers (Item 7) to the bubbler fitting.
6. Apply thread sealer (not provided) to the bubbler fitting
threads.
7. Assemble the bubbler to the bubbler fitting and tighten the
bubbler fitting. The bubbler should be one quarter turn less
than the desired position when the bubbler fitting is securely
tightened from the underside of the basin.
8. For proper function of the lockwashers, the bubbler must be
turned the last quarter turn from the upper side of the basin.
This assembly method seats the lockwashers properly for
correct operation.
9. Operate the unit and check for leaks.
10. Remove all existing exterior screws and replace with a
tamper-resistant screw of the same length and size (provided).
Special drive bits are provided for the tamper-resistant screws.
Note: The number of tamper-resistant screws used/required
will vary depending on fountain or cooler model. Detailed
instructions included in owners manual.
Installation Instructions
For 98030C
Vandal-Resistant Kit
Remove old drain plug and original gasket and discard.
Replace with new one-piece drain.
Loading...