Halsey Taylor 5905 User Manual
These fountains are certified to
NSF/ANSI 61.
GENERAL
Face-mounted fountain, one-piece, noncorrosive stainless steel number 300 series
with brushed satin finish. Contour-formed basin
with rounded corners and edges reduces
splatter, insures proper drainage and prevents
standing waste water.
BUBBLER
Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.
PUSHBUTTON ACTUATION MECHANISM
Self-closing, vandal-resistant pushbutton does
not require grasping or twisting.
AUTOMATIC STREAM HEIGHT REGULATOR
Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.
INLET STRAINER
Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.
WATER INLET
3/8" O.D. Tubing
DRAIN OUTLET
1-1/4" tube outlet for 1-1/4" slip joint connection.
■ Shipping weight: 10 lbs.
SUGGESTED SPECIFICATIONS
Fountain shall include pushbutton on the front,
contour-formed basin to eliminate splashing and
standing water, and shall have rounded corners
and edges. Projector shall be two-stream,
mound-building type with integral hood guard and
anti-squirt feature. The manufacturer shall certify
the unit to meet the requirements of NSF/ANSI 61,
and the Safe Drinking Water Act.
Note: Continued product improvement makes
specifications subject to change without notice.
See Halsey Taylor website for most current
spec sheet.
Model: 5905 AC
ALL CLIMATE FOUNTAIN
■ Same as 5905 with Freeze-Resistant Valve
for installation in cold temperatures
■ Shipping weight: 26 lbs.
Optional Accessories (extra cost)
■■
Vandal-Resistant Kit
5905 - Trap and service stop not included.
5905AC - Service stop not included.
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
D11 / 1-2005
MODEL: ■■5905 ■■5905 AC
Face-Mounted Fountain
www.halseytaylor.com
5905 / 5905 AC
Printed in the U.S.A.
Face Mounted Fountain
(CONTINUED)
MOUNTING INSTRUCTIONS
• Establish the rim height of fountain to be
mounted.
• Refer to rough-in for location of plumbing
through wall.
• Mount fountain hanger on wall as shown.
• Locate trap (not furnished) on waste line —
see rough-in for proper distance from wall.
• Install service valve (not furnished) on building
water supply line.
• Hang fountain on wall and adjust hanger
(if necessary) for proper fit to trap.
• Connect fountain supply line to service valve.
• Tighten drain plug into fountain, and secure
fountain to wall with screws (furnished).
• Open service valve fully and check for water
leaks.
• Stream height is factory set 45-50 psi. If water
pressure varies greatly from this, adjust
automatic stream regulator (on valve body) to
provide drinking stream approx. 11⁄2” above
projector guard.
CAUTION – Fountain must be securely
bolted to wall
OPERATING PRESSURES:
Supply water-105 psi maximum
FRONT VIEW
SIDE VIEW
❏ 5905
FRONT VIEW
SIDE VIEW
❏ 5905AC
Installation Instructions for 5905AC
1. Frame Wall
2. Remove bottom cover from fountain and
save the screws. Assemble push rod to fountain.
(push rod provided with freeze-resistant box)
3. Install the fountain using bolts and washers
(not provided). Tighten securely.
4. Attach drain tube to fountain and cut to
required length using the freeze-resistant box
as a guide. 1-1/4" waste outlet located in
freeze-resistant valve system.
5. Install freeze-resistant box behind non-
freezing wall - see box instructions.
6. Install a service stop (not provided) and
make water supply connection from the stop to
the strainer in the freeze-resistant box. DO NOT
SOLDER TUBES INSERTED INTO THE
STRAINER AS DAMAGE TO THE O-RINGS
MAY RESULT.
7. Connect fountain water line to freeze-resistant
box - see box instructions. Replace bottom
cover. 3/8" O.D. tubing to freeze-resistant box.
CAUTION – Fountain must be securely
bolted to wall
Loading...