Halsey Taylor 5801C User Manual
This fountain is certified to
NSF/ANSI 61.
GENERAL
Semi-recessed fountain, one-piece,
non-corrosive stainless steel number 300
series with brushed satin finish. Contourformed basin with rounded corners and edges
reduces splatter, insures proper drainage and
prevents standing waste water. Cuspidor may
be mounted to right or left of fountain.
BUBBLER
Exclusive one-piece, chrome-plated two-stream
mound-building bubbler with non-removable
anti-squirt feature and integral hood insures a
satisfying drink of water.
PUSHBUTTON ACTUATION MECHANISM
Self closing, vandal-resistant pushbutton does
not require grasping or twisting. Cuspidor flushing
jet operates when drinking fountain is actuated.
AUTOMATIC STREAM HEIGHT REGULATOR
Self-closing assembly is located inside unit to
prevent tampering. Unit resists corrosion and
liming. A constant stream height is automatically
maintained under line pressures that vary from
20 to 105 psi.
INLET STRAINER
Easily cleaned in-line strainer screen traps
particles of 140 microns or larger before they
enter the waterway.
WATER INLET
3/8" O.D. Tubing
DRAIN OUTLET
1-1/2" tube outlet for 1-1/2" slip joint connection.
SUGGESTED SPECIFICATIONS
Fountain shall include pushbutton on the front,
contour-formed basin to eliminate splashing and
standing water, and shall have rounded corners
and edges. Projector shall be two-stream,
mound-building type with integral hood guard and
anti-squirt feature. The manufacturer shall certify
the unit to meet the requirements of NSF/ANSI 61,
and the Safe Drinking Water Act.
Note: Continued product improvement makes
specifications subject to change without notice.
See Halsey Taylor website for most current
spec sheet.
Standard finish is Stainless Steel
Important: When using 5801 drinking fountain
in conjunction with cuspidor, specification
should state “with cuspidor connection for bypass
to cuspidor.” Use 5801C when ordering.
Optional Accessories (extra cost)
■■
Glass Filler (factory installed No. 2408 style glass filler only).
■■
Vandal-Resistant Kit
■■
Easy-Flex™Bubbler
Trap and service stop not included.
Shipping weight: 40 lbs.
HALSEY TAYLOR, 2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
D4 / 1-2005
MODEL:■■5801C Fountain w/cuspidor connection
Fountain and Cuspidor
Semi-Recessed
www.halseytaylor.com
Printed in the U.S.A.
Semi-Recessed Fountain
and Cuspidor
(CONTINUED)
MOUNTING INSTRUCTIONS
Refer to diagrams for rough-in of plumbing and
for size of wall cut out. Final check for leaks and
correct functions of fountain should be made.
(For details see the installation instructions.)
Installation requires trap to be installed in
wall. A service supply stop must be installed
at the fountain inlet line. Trap and service
stop not included.
NOTE: Supply line between fountain and cuspidor
to be furnished and installed by contractor.
OPERATING PRESSURES
Supply water-105 psi maximum
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION 3/8" O.D. UNPLATED COPPER TUBE CONNECT STUB
1-1/2" (38mm) OUT FROM WALL SHUT OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/2" O.D. DRAIN
C = WALL SCREW HOLES
FOUNTAIN AND CUSPIDOR COMBINATION WITH SPECIAL OUTLET BETWEEN VALVE AND PROJECTOR TO SUPPLY
FLUSHING JET ON CUSPIDOR. CUSPIDOR CAN BE MOUNTED ON LEFT (AS SHOWN) OR TO RIGHT OF FOUNTAIN.
FOUNTAIN
CUSPIDOR
FRONT VIEW
SIDE VIEW
FRONT VIEW
Loading...