Halo Lighting System CHSL600, HSL600 User Manual
Instruction Manual
Instrucciones
Directives
HSL600
CHSL600
HSL600
CHSL600
Congratulations! You have purchased a Regent 600 watt dimmable halo-
gen shoplight which will provide you with years of trouble-free service. This
light has been designed to provide instant on, pure white light in a workshop,
garage, basement or any place where an intense bright area light is needed.
The fixture also has the capability of being adjusted to aim light without having to move the fixture to a new location.
What you need
• Screwdriver
• (2) Toggle bolts if mounted into drywall only
What’s included
• Fully assembled fixture with mounting chains (A)
• (2) “J” screw hooks (B)
• (2) 300 watt premium halogen bulbs (C)
• 12” switch chain extension (D)
• (2) Wire safety guards/lenses (E)
What to know
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK,
EXPOSURE TO EXCESSIVE UV RADIATION OR INJURYTO PERSONS
IMPORTANT SAFETY INSTRUCTIONS.
WARNING:To reduce the risk of FIRE, ELECTRIC SHOCK, EXPOSURE TO
EXCESSIVE UV RADIATION OR INJURY TO PERSONS:
• Lighted lamp is HOT!
• Do not remain in light if skin feels warm.
• For indoor use only.
• UL and CSA listed for dry locations.
• Fixture must be connected to a 120 Volt, 60 Hz power source. Any other
connection voids warranty.
• Keep away from flammable objects.
• The bulb and fixture get extremely hot during use. Always
unplug the light and let it cool 5 minutes before attempting to
touch the fixture. Be sure to use handle to reposition fixture.
• Do not touch hot lens, guard, or enclosure.
• Bulb gets HOT quickly! Only contact switch/plug when turning on.
• The electrical system, and the method of electrically connecting the fixture
to it, must be in accordance with the National Electrical Code and local
building codes.
• Do not operate the unit with a missing or damaged wire safety guard, safety
glass lens (lamp containment), or UV filter.
• Do not direct the light at persons or look directly at lighted fixture.
A
E
B
C
D
2
• Use only with a 300 watt or smaller bulb. Installing a bulb of a higher
wattage could create a fire hazard. Use of higher wattage bulb will void the
warranty.
• Never touch the bulb with your bare hands. Oil from your skin can cause
premature failure. Always handle the bulb with gloves or a soft cloth.
• If lens is replaced, use only a diffused tempered safety glass of equal
thickness.
• For maximum bulb life, position light so that the quartz halogen bulb
remains within 4° of horizontal.
• Disassembly of your fixture will void the warranty.
Installing the bulbs
Step 1: Loosen the screw and retaining clip that secures the wire guard and
lens assembly.
Step 2: Rotate the retaining clip so that the wire guard and lens assembly
will swing down.
Step 3: Remove bulb and CAUTION sheet from inside wire guard and lens
assembly. Unpack bulb, being careful not to touch with your bare
hands (see caution sheet packed with bulb).
Step 4: Using gloves or a soft cloth, gently press the bulb to one side of the
socket and insert the opposite end into the other side of the socket.
Reverse this procedure to remove the bulb.
Step 5: Close wire guard and lens assembly. Rotate retaining clip to secure
and retighten retaining clip screw.
Step 6: Repeat Steps 1 through 5 for the other bulb.
NOTE: Should the light not turn on when power is applied and the switch is
turned on, unplug the fixture, then check to be sure both bulbs are seated
properly in the socket receptacles.
Hanging your fixture
Step 1: After selecting the installation location site on your ceiling, determine
if you can install “J” screw hooks (included) directly into ceiling joists
or studs in your ceiling. If not, you will need to use two drywall toggle bolts (not included). NOTE:The “J” screw hooks should be positioned 32” apart so that the fixture chains are hanging straight from
the ceiling to the fixture.
Step 2: Install “J” screw hooks into the ceiling joists or drywall toggle bolts,
making sure they are tight and secure.
Step 3: Hang both chains (already attached to the fixture) over the “J” screw
hooks installed in Step 2. NOTE: This fixture must be hung at least
12” from the ceiling and the wall for proper ventilation.
How to use
Step 1: Plug the power cord into a 120 Volt receptacle.
Step 2: Pull the switch chain located in the center of the fixture to turn the
fixture on in the dim or 300 watt mode. Pull the switch chain again
to turn the fixture on to the bright or 600 watt mode. Pull the switch
3
chain once again to turn the fixture off. NOTE: If the switch chain is
too short to reach, a 12” extension chain has been included which
can easily snap onto the bottom of the switch chain.
How to adjust the light direction of your fixture
To adjust the aiming function of your shoplight, loosen the two plastic locking
knobs located on top of the fixture just below the eye bolts. Grasping the
handles located on each end of the fixture, rotate the fixture to the desired
location, then retighten both plastic locking knobs.
WARNING:The halogen bulbs and fixture housing get hot during use. Do
not touch the bulbs or fixture housing until they have had time to cool.
WARNING: Deviation from the assembly instructions may result in a risk of
fire or electric shock.
SAVE THESE INSTRUCTIONS.
Five year limited warranty
Regent Lighting Corporation (“the Company”) warrants this product (the “product”) against defects
in material or workmanship for a period of five years from date of original purchase, and agrees to
repair or, at the Company’s option, replace a defective product without charge for either replacement parts or labor during such time. This does not include labor to remove or install fixtures.
This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or
other proof of date of original purchase acceptable to the Company is required before warranty performance shall be rendered.
This warranty only covers product failure due to defects in materials or workmanship which occurs
in normal use. It does not cover the bulb or failure of the product caused by accident, misuse,
abuse, lack of reasonable care, alteration, faulty installation, subjecting the product to any but the
specified electrical service or any other failure not resulting from defects in materials or workmanship. Damage to the product caused by separately purchased, non-Company brand replacement
bulbs and corrosion or discoloration of brass components are not covered by this warranty.
There are no express warranties except as described above.
THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THE PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY. ALLIMPLIED WARRANTIES, IF ANY, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TOTHE DURATION OF THIS EXPRESS WARRANTY. Some states do
not allow the exclusion or limitation of incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or limitations may not apply to you.
No other warranty, written or verbal, is authorized by the Company. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
To obtain warranty service, please write to Regent Lighting Corporation, 2611 La Vista Drive,
Burlington, NC 27215. Enclose product model number and problems you are experiencing, along
with your address and telephone number. You will then be contacted with a solution, or a Return
Goods Authorization number and full instructions for returning the product. All returned products
must be accompanied by a Return Goods Authorization Number issued by the Company and must
be returned freight prepaid. Any product received without a Return Goods Authorization
Number from the Company will be refused.
Regent Lighting is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery
and a claim filed with them.
REGENT LIGHTING CORPORATION
2611 La Vista Drive, Burlington, NC 27215 USA
Reproductions of this document without prior written approval of Regent Lighting Corporation are strictly prohibited
1-800-334-6871
www.regentlighting.com
Patents Pending
4
Loading...