Page 1
Video to PC/HDTV Switching Scaler
Composite, S-Video, Component, PC and HDMI AV Inputs
HDMI AV Output with Separate Digital Audio Output
Front Panel, IR Remote, & RS-232 Serial Control
SUPPORT &
ORDERING
INFORMATION
For technical support, Call 714-641-6607 or fax 714-641-6698
Order by phone: toll-free in the U.S. 800-959-6439
Web site: www.hallresearch.com
Hall Research 1163 Warner Ave. Tustin, CA 92780
MODEL SC1080-H
UMA1165 Rev A
Page 2
Page 3
Multi Input Digital Scaler with Audio
TRADEMARKS USED IN THIS MANUAL
Hall Research, HR, and the
Any other trademarks mentioned in this manual are acknowledged to be the property of the
trademark owners.
logo are trademarks of Hall Research Inc.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used properly, that is, in strict accordance with the manufacturer’s
instructions, may cause interference to radio communication. It has been designed to
comply with the limits for a Class A computing device in accordance with the
specifications in Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when the equipment is operated in a
commercial environment. Operation of this equipment in a residential area is likely to
cause interference, in which case the user at there own expense will be required to take
whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of the Canadian
Department of Communications.
1
Page 4
Model SC1080-H
Contents
1. INTRODUCTION ........................................................................................................... 3
1.1 GENERAL...........................................................................................................3
1.2 FEATURES......................................................................................................... 4
2. INSTALLATION ............................................................................................................ 5
2.1 CONNECTING THE VIDEO INPUTS ......................................................................... 5
2.2 CONNECTING THE SCALED OUTPUT..................................................................... 6
2.3 OTHER CONNECTIONS ........................................................................................ 6
3. CONFIGURATION & OPERATION .............................................................................. 7
3.2 OSD MENU FOR VGA INPUT SIGNAL................................................................... 8
3.3 OSD MENU FOR CV, SV, YPBPR & HDMI INPUT SIGNALS .......................................... 9
3.4 INFRA-RED REMOTE CONTROL (IR REMOTE)..................................................... 10
3.5 FRONT PANEL LOCKOUT ................................................................................... 11
4. SERIAL CONTROL..................................................................................................... 12
4.1 READ COMMANDS ............................................................................................ 13
4.2 KEY COMMANDS............................................................................................... 14
4.3 SET COMMANDS............................................................................................... 14
5. TROUBLESHOOTING................................................................................................ 17
5.1 RESETTING THE SC1080-H TO FACTORY DEFAULTS..........................................17
5.2 CALLING HALL RESEARCH ................................................................................ 17
5.3 SHIPPING AND PACKAGING................................................................................ 17
6. SPECIFICATIONS ...................................................................................................... 18
6.1 SUPPORTED INPUT FORMATS............................................................................ 18
6.2 AVAILABLE OUTPUT FORMATS........................................................................... 18
2
Page 5
Multi Input Digital Scaler with Audio
1. Introduction
1.1 General
The SC1080-H is a multiple format switching video scaler. It has 5
different types of video inputs and a scaled digital output that can be
switched to any of the inputs. The SC1080-H accepts various input
formats and resolutions and scales to a specific output format and
resolution.
Inputs are: HDMI (up to 1080i/p), PC (from VGA (640x480) to WUXGA
(1920x1200), Component Video (SD and HD from 480p to 1080i/p), Svideo (NTSC or PAL) and Composite Video (NTSC or PAL).
The output format and resolution can be specified as either PC (VGA
(640x480) to WUXGA (1920x1200)) or Component Video (YPbPr from
480i/p to 1080i/p).
The Video Scaler can be controlled in many ways including: front panel
lighted pushbuttons (with On-Screen Display menus), using the included
IR remote control, or RS-232 Serial interface. The controls include: input
switching, setting the output resolution, picture adjustment (color,
brightness, contrast, and sharpness), aspect ratio (Standard, 16:9 or
4:3), digital noise reduction, 3D comb filter ON/Off, and many other
advanced features.
The SC1080-H is ideal for use with in boardrooms, classrooms, digital
signage, and high end home-theatre applications. Its output can be set
for any LCD projector, PC LCD monitor, plasma, or HDTV displays.
The unit is shipped with (1) universal power supply, (1) DB15P-M-M
cable, (1) 3 RCA to RCA (R-G-B) cable and (1) 3 RCA to RCA (Y-R-W)
and IR remote.
3
Page 6
Model SC1080-H
1.2 Features
• HDMI 1.2, HDCP 1.1 and DVI 1.0 Compliant.
• 5 different inputs: HDMI, PC, YPbPr, S-video and Composite.
• Provides YPbPr HDTV outputs of 480i/p, 576i/p, 720p, 1080i, 1080p
and up to WUXGA (1920x1200) PC resolutions
• Converts Digital and Analog audio signals into Digital Format for output
on HDMI combined with the video or separate Coaxial S/PDIF.
• RS-232 interface allows control from an external device.
• OSD (On-Screen Display).
Horizontal mirroring (X-axis flip)
•
• Easy to use IR remote control.
• EDID Support.
• Reverse 3:2/2:2 pull down provides clear and crisp de-interlacing of
video originating from 24 fps film, such as DVD movies.
• Digital noise reduction.
• Brightness, Color, Contrast, Sharpness and Tint adjustment.
• Adaptive 3-D comb filter (3-D Motion and 3-D De-Interlacing) for
composite input ensures jitter-free picture.
• Compatible with NTSC and PAL video input.
Figure 1 - Accessories
4
Page 7
Multi Input Digital Scaler with Audio
2. Installation
2.1 Connecting the Video inputs
The video scaler accepts both TV and PC inputs and scales them to your
desired high resolution format output. The TV inputs are composite video
(CV), S-Video (Mini-Din connector), YPbPr input (3 RCA connectors),
PC (HD15) and HDMI™.
Figure 2 - Rear Panel
S-Video: Use an S-Video cable to connect the S-Video output of the
source equipment to the connector labeled “S-Video” on the back of the
Video Scaler. The format can be NTSC or PAL. This channel accepts
stereo audio input via (2) RCA connectors.
Composite Video (CV): Use a Composite video cable to connect the
composite video output of the source equipment to the connector labeled
“CV” on the back of the Video Scaler. The format can be NTSC or PAL.
This channel accepts stereo audio input via (2) RCA connectors.
YPbPr: Use a 3 RCA-to-3 BNC YPbPr cable to connect the YPbPr
output of the source equipment to the device. The format can be NTSC
or PAL. This channel accepts stereo audio input via (2) RCA connectors.
PC input: Connect the source computer's VGA output signal to the
HD15 connector labeled “PC” on the device. This channel accepts stereo
audio input via a 3.5mm audio jack (TRS – Tip, Ring, and Sleeve).
HDMI™ input: Use an HDMI™ cable to connect the HDMI™ output of
the source equipment to the device. This channel accepts digital audio
input via HDMI or stereo audio via a 3.5mm audio jack (TRS – Tip, Ring,
and Sleeve).
5
Page 8
Model SC1080-H
2.2 Connecting the Scaled Output
The output of the SC1080-H can be connected to any HDMI™
compatible LCD, Projector, or Plasma display by using the appropriate
cable.
Figure 3 - Block Diagram
2.3 Other Connections
RS-232: Connect a serial control device to the 9-pin D-sub connector
labeled “RS-232”
Power: Use only the 5V 2.6A DC power input (center positive 2.1 mm
jack) supplied with the unit.
6
Page 9
6
Multi Input Digital Scaler with Audio
3. Configuration & Operation
3.1 Front Panel
5
1
. Source Selection: Press the appropriate button to output that
11.
connected audio and video selection.
. Menu: Press the menu button to bring up the OSD operation menu.
22.
. Enter: Press the button to confirm selections made in the OSD.
33.
Figure 4 - Front Panel
2
4
3
. ▲or▼: Press to toggle through various adjustment controls to alter
44.
the settings.
. IR Sensor: Infrared remote control sensor.
55.
. Power Button: Press once to power on the unit, press again to
66.
turn off.
7
Page 10
Model SC1080-H
3.2 OSD Menu for VGA Input Signal
Top Menu Sub-Menu Value
PC
CONTRAST 0 to 100%
BRIGHTNESS 0 to 100%
V-POSITION 0 to 100%
CLOCK 0 to 100%
PHASE 0 to 100%
SCALE
MIRROR OFF or ON
COLOR
COLOR TEMP NORMAL, USER, COOL, WARM
Only in USER Mode
Only in USER Mode
Only in USER Mode
OUTPUT
OSD
H-POSITION 0 to 100%
V-POSITION 0 to 100%
TIMEOUT 0 to 100%
BACKGROUND 0 to 8
AUDIO
SOURCE HDMI / L/R4 / COAXIAL
DELAY OFF / 40ms / 110ms / 150ms
SOUND ON / MUTE
INFORMATION
H-POSITION 0 to 100%
FULL, OVERSCAN, UNDERSCAN, LETTERBOX,
RED 0 to 100%
GREEN 0 to 100%
BLUE 0 to 100%
NATIVE / VGA / SVGA / XGA / SXGA / UXGA /
SXGA+ / WXGA / WSXGA / WUXGA / WXGA+ /
480i / 480p / 576i / 576p / 720p @ 60Hz
1080i @ 50Hz
1080i @ 60Hz
1080p @ 50Hz
1080p @ 60Hz
SOURCE (Input Interface)
INPUT ( Input Resolution)
OUTPUT (Output Resolution)
VERSION (Firmware Version)
PANSCAN
8
Page 11
Multi Input Digital Scaler with Audio
3.3 OSD Menu for CV, SV, YPbPr & HDMI Input Signals
Top Menu Sub-Menu Value
VIDEO
PICTURE MODE STANDARD, MOVIE, VIVID, USER
Adj only in USER
PICTURE MODE
Adj only in USER
PICTURE MODE
Adj only in USER
PICTURE MODE
Adj only in USER
PICTURE MODE
Adj only in USER
PICTURE MODE
SCALE
MIRROR OFF or ON
NR OFF or ON
COLOR
COLOR TEMP NORMAL, USER, COOL, WARM
Only in USER Mode
Only in USER Mode
Only in USER Mode
OUTPUT
OSD
H-POSITION 0 to 100%
V-POSITION 0 to 100%
TIMEOUT 0 to 100%
BACKGROUND 0 to 8
AUDIO
SOURCE
DELAY OFF / 40ms / 110ms / 150ms
SOUND ON / MUTE
INFORMATION
CONTRAST 0 to 100%
BRIGHTNESS 0 to 100%
HUE 0 to 100%
SATURATION 0 to 100%
SHARPNESS 0 to 100%
FULL, OVERSCAN, UNDERSCAN, LETTERBOX,
PANSCAN
RED 0 to 100%
GREEN 0 to 100%
BLUE 0 to 100%
NATIVE / VGA / SVGA / XGA / SXGA / UXGA /
SXGA+ / WXGA / WSXGA / WUXGA / WXGA+ /
480i / 480p / 576i / 576p / 720p @ 60Hz
1080i @ 50Hz
1080i @ 60Hz
1080p @ 50Hz
1080p @ 60Hz
HDMI / L/Rx / COAXIAL
Where ‘x’ is 1 for CV, 2 for SV, 3 for YPbPr and 5 for HDMI
SOURCE (Input Interface)
INPUT ( Input Resolution)
OUTPUT (Output Resolution)
VERSION (Firmware Version)
9
Page 12
Model SC1080-H
3.4 Infra-Red Remote control (IR Remote)
1. Power: Power unit ON/OFF.
2. Input: Toggle through input sources.
3. HD: Select Component Input.
4. PC: Select PC input.
5. HDMI/DVI: Select HDMI Input.
6. Output Resolution: Select various output
resolutions directly. Others are available via the
OSD.
7. EXIT: Select to exit OSD menu
8. MENU: Select to show OSD
9. OK: Select to confirm a selection.
10. UP/DOWN/LEFT/RIGHT: Select to move in
OSD menu or to change a selection.
11. RESET: Press and hold for 5 seconds to
reset firmware to factory defaults.
12. AUTO ADJUST: Select to automatically
optimize picture centering on the screen.
10
Page 13
Multi Input Digital Scaler with Audio
3.5 Front Panel Lockout
Under certain circumstances it may be desirable to disable the front
panel controls (e.g. to prevent unauthorized or accidental changes to the
settings while the unit is in use). To disable the front panel controls you
must use the RS-232 port (see Serial Control section for details).
It is still possible to remove the lockout from the front panel by
performing a full factory default reset operation!
To reset to the factory default settings press the RESET button on the IR
remote control for 5-10 seconds. The SC1080-H led’s will turn on while
the reset button is depressed and turn back off when the software reset
has completed.
11
Page 14
Model SC1080-H
4. Serial Control
The video input selection and signal parameter settings for the SC1080H can be controlled via an external control system by using the RS-232
port on the unit.
Use a straight thru M/F DB9 serial cable to connect the unit to the PC.
Only the TX, RX and GND pins are implemented in the connector. The
RS232 port operates at 19200 baud, no parity and 1 stop bit. In
response to a valid command, the SC1080-H will respond with CR, LF,
>, SPACE and then the listed response. Commands may be entered as
uppercase or lowercase.
With most commands, the SC1080-H will reply immediately, but other
commands may take a few seconds to complete. The user must wait for
the full response before issuing more commands to the unit.
For Example
Sending a POWER ON Command (“S POWER 1<CR>”) results in the
following response from the SC1080-H:
SENT
53 20 50 4F 57 45 52 20 31 0D
S P O W E R 1 CR
RECEIVED
0D 0A 3E 20 50 4F 57 45 52 20 4F 4E 0D 0A
CR LF > P O W E R O N CR LF
The unit must be powered on with either the front panel push button or
by sending the POWER ON Command before the unit will respond as
listed. Sending any commands with the unit powered off will result in the
following response from the unit.
Please turn on power. ( K POWER / S POWER ON ).
12
Page 15
Multi Input Digital Scaler with Audio
4.1 Read Commands
Command Response Description
R POWER > POWER ON SHOW POWER STATUS
R SOURCE > SOURCE CV~HDMI SHOW SOURCE STATUS
R OUTPUT > OUTPUT NATIVE~WUXGA SHOW OUTPUT STATUS
R SIZE > SIZE FULL or OVERSCAN or
UNDERSCAN or LETTERBOX or
PANSCAN
R PICTUREMODE > PICTUREMODE STANDARD or MOVIE
or VIVID or USER
R CONTRAST > CONTRAST 0~100 SHOW CONTRAST STATUS
R BRIGHTNESS > BRIGHTNESS 0~100 SHOW BRIGHTNESS
R HUE > HUE 0~100 SHOW HUE STATUS (default=50)
R SATURATION > SATURATION 0~100 SHOW SATURATION STATUS
R SHARPNESS > SHARPNESS 0~100 SHOW SHARPNESS STATUS
R NR > NR OFF or LOW or MIDDLE or HIGH SHOW NR STATUS
R PCHPOSITION > PCHPOSITION 0~100 SHOW PC H-POSITION STATUS
R PCVPOSITION > PCVPOSITION 0~100 SHOW PC V-POSITION STATUS
R PCCLOCK > PCCLOCK 0~100 SHOW PC COLOK STATUS
R PCPHASE > PCPHASE 0~63 SHOW PC PHASE STATUS
R COLORTEMP > COLORTEMP NORMAL or WARM or
COOL or USER
R RED > RED 0~100 SHOW COLOR TEMP RED STATUS
R GREEN > GREEN 0~100 SHOW COLOR TEMP GREEN
R BLUE > BLUE 0~100 SHOW COLOR TEMP BLUE STATUS
R OSDHPOSITION > OSDHPOSITION 0~100 SHOW OSD H-POSITION STATUS
R OSDVPOSITION > OSDVPOSITION 0~100 SHOW OSD V-POSITION STATUS
R OSDTIMEOUT > OSDTIMEOUT 0~100 SHOW OSD TIMEOUT STATUS
R OSDBACKGROUND > OSDBACKGROUND 0~8 SHOW OSD BACKGROUND STATUS
R AUDIOMUTE > AUDIOMUTE OFF or ON SHOW AUDIO MUTE STATUS
R AUDIODELAY > AUDIODELAY OFF or 1 to 150MS SHOW AUDIO DELAY STATUS
R MIRROR > MIRROR OFF or ON SHOW MIRRORING STATUS
R KEYLOCK > KEYLOCK OFF or ON SHOW FRONT PANEL LOCK STATUS
R RESET > RESET ON SHOWS RESET STATUS
An invalid command will respond with “R-[??]”<CR>
SHOW SIZE STATUS
SHOW PICTURE MODE STATUS
(default = Standard)
(default=50)
STATUS(default=53)
(default=53)
(default=48)
(default=OFF)
(default=50)
(default=100)
(default=2)
(default=61)
SHOW COLOR TEMP STATUS
(default=Normal)
(default=47)
STATUS (default=47)
(default=47)
(default=50)
(default=50)
(default=10)
(default=5)
(default=OFF)
(default=OFF)
13
Page 16
Model SC1080-H
4.2 Key Commands
Command Response Description
K POWER > POWER PRESS POWER BUTTON
K MENU > MENU PRESS MENU BUTTON
K UP > UP PRESS UP BUTTON
K DOWN > DOWN PRESS DOWN BUTTON
An invalid command will respond with “K-[??]”<CR>
4.3 Set Commands
Command Response Description
S POWER 0 > POWER OFF POWER OFF
S POWER 1 > POWER ON POWER ON
S SOURCE 0 > SOURCE CV CV INPUT
S SOURCE 1 > SOURCE SV SV INPUT
S SOURCE 2 > SOURCE COMP COMP INPUT
S SOURCE 3 > SOURCE PC PC INPUT
S SOURCE 4 > SOURCE HDMI HDMI INPUT
S OUTPUT 0 > OUTPUT NATIVE NATIVE RESOLUTION
S OUTPUT 1 > OUTPUT VGA VGA RESOLUTION
S OUTPUT 2 > OUTPUT SVGA SVGA RESOLUTION
S OUTPUT 3 > OUTPUT XGA XGA RESOLUTION
S OUTPUT 4 > OUTPUT SXGA SXGA RESOLUTION
S OUTPUT 5 > OUTPUT UXGA UXGA RESOLUTION
S OUTPUT 6 > OUTPUT 480I 480I RESOLUTION
S OUTPUT 7 > OUTPUT 480P 480P RESOLUTION
S OUTPUT 8 > OUTPUT 720P 720P 60HZ RESOLUTION
S OUTPUT 9 > OUTPUT 1080I 1080I 60HZ
S OUTPUT 10 > OUTPUT 1080P 1080P 60HZ
S OUTPUT 11 > OUTPUT 576I 576I 60HZ RESOLUTION
S OUTPUT 12 > OUTPUT 576P 576P 60HZ RESOLUTION
S OUTPUT 13 > OUTPUT 720P 720P 50HZ RESOLUTION
S OUTPUT 14 > OUTPUT 1080I50 1080I 50HZ
S OUTPUT 15 > OUTPUT 1080P50 1080P 50HZ
S OUTPUT 16 > OUTPUT WXGA WXGA RESOLUTION
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
RESOLUTION OUTPUT
RESOLUTION OUTPUT
OUTPUT
OUTPUT
OUTPUT
RESOLUTION OUTPUT
RESOLUTION OUTPUT
OUTPUT
14
Page 17
S OUTPUT 17 > OUTPUT WSXGA WSXGA RESOLUTION
S OUTPUT 18 > OUTPUT WUXGA WUXGA RESOLUTION
S OUTPUT 19 > OUTPUT WXGA+ WXGA+ RESOLUTION
S OUTPUT 20 > OUTPUT SXGA+ SXGA+ RESOLUTION
S SIZE 0 > SIZE FULL SCALER FULL OUTPUT
S SIZE 1 > SIZE OVERSCAN SCALER OVERSCAN
S SIZE 2 > SIZE UNDERSCAN SCALER UNDERSCAN
S SIZE 3 > SIZE LETTERBOX SCALER LETTERBOX
S SIZE 4 > SIZE PANSCAN SCALER PANSCAN
S PICTUREMODE 0~3 > PICTUREMODE
STANDARD~USER
S CONTRAST 0~100 > CONTRAST 0~100 CONTRAST 0~100
S BRIGHTNESS 0~100 > BRIGHTNESS 0~100 BRIGHTNESS 0~100
S HUE 0~100 > HUE 0~100 HUE 0~100 ADJUST
S SATURATION 0~100 > SATURATION 0~100 SATURATION 0~100
S SHARPNESS 0~100 > SHARPNESS 0~100 SHARPNESS 0~100
S NR 0~3 > NR OFF~HIGH 0:OFF; 1:LOW;
S PCHPOSITION 0~100 > PCHPOSITION 0~100 H POSITION 0~100
S PCVPOSITION 0~100 > PCVPOSITION 0~100 V POSITION 0~100
S PCCLOCK 0~100 > PCCLOCK 0~100 PC MODE COLCK 0~100
S PCPHASE 0~63 > PCPHASE 0~63 PC MODE PHASE 0~63
S COLORTEMP 0~3 > COLORTEMP
NORMAL~USER
S RED 0~100 > RED 0~100 COLOR TEMP "RED"
S GREEN 0~100 > GREEN 0~100 COLOR TEMP "GREEN"
S BLUE 0~100 > BLUE 0~100 COLOR TEMP "BLUE"
Multi Input Digital Scaler with Audio
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
0:STANDARD; 1:MOVIE;
2:VIVID;
3:USER, PICTURE MODE
OUTPUT
ADJUST [Default:50]
ADJUST [Default:53]
[Default:50]
ADJUST [Default:53]
ADJUST [Default:48]
2:MIDDLE; 3:HIGH, NR
CONTROL [Default:Off]
ADJUST [Default:50]
ADJUST [Default:100]
ADJUST [Default:2]
ADJUST [Default:61]
0:NORMAL; 1:WARM;
2:COOL; 3:USER,
COLOR TEMP SETTING
[Default:NORMAL]
ADJUST [Default:47]
ADJUST [Default:47]
ADJUST [Default:47]
15
Page 18
Model SC1080-H
S OSDHPOSITION 0~100 > OSDHPOSITION 0~100 OSD H POSITION 0~100
S OSDVPOSITION 0~100 > OSDVPOSITION 0~100 OSD V POSITION 0~100
S OSDTIMEOUT 0~100 > OSDTIMEOUT 0~100 OSD TIMEOUT 0~100
S OSDBACKGROUND 0~8 > OSDBACKGROUND 0~8 OSD OSDBACKGROUND
> AUDIOMUTE OFF~ON S AUDIOMUTE 0~1
S AUDIODELAY 0~1 > AUDIODELAY OFF~ON 0:OFF; 1:ON, AUDIO
S MIRROR 0~1 > MIRROR OFF~ON 0:OFF;1:ON, MIRRORING
S KEYLOCK 0~1 > KEYLOCK OFF~ON 0:OFF;1:ON, FRONT
S RESET 0~1 > RESET ON 0:OFF;1:ON, RESET to
ADJUST [Default:50]
ADJUST [Default:50]
SETTING [Default:10]
SECONDS
0~8 ADJUST [Default:5] 0
= Darkest Background; 8 =
Transparent Background
0:OFF; 1:ON, AUDIO
MUTE CONTROL
[Default:Off]
DELAY CONTROL
[Default:Off]
[Default:Off]
PANEL LOCK [Default:Off]
DEFAULTS [Default:Off]
An invalid command will respond with “S-[??]-[xx]”<CR>
16
Page 19
Multi Input Digital Scaler with Audio
5. Troubleshooting
Hall Research highly recommends that all products be assembled,
configured and tested prior to the final installation to eliminate the
possibility of problems on site.
There are no field serviceable parts or circuits in the device. If you think
that the device is malfunctioning, please first try to reset to factory default
settings:
5.1 Resetting the SC1080-H to Factory Defaults
There are no field serviceable parts or circuits in the device. If you think
that the device is malfunctioning, please first try to reset to the factory
default settings (using the RESET button on the IR remote control), and
set the output either to XGA (Press MENU + ▲) or 480p (Press MENU +
▼) to obtain an image on your LCD.
5.2 Calling Hall Research
If you determine that your SC1080-H is malfunctioning, do not attempt to repair the unit.
There are no user serviceable parts inside the unit. Opening the unit will void the
warranty.
Contact the Hall Research Technical Support department at 714-641-6607 to obtain an
RMA (Return Authorization) number.
Before you do, make a record of the history of the problem. We will be able to provide
more efficient and accurate assistance if you have a complete description.
5.3 Shipping and Packaging
If you need to transport or ship your device:
• Package it carefully. We recommend that you use the original container if possible.
• Before you ship the units back to Hall Research for repair or return, contact us to
get a Return Authorization (RMA) number.
17
Page 20
Model SC1080-H
6. Specifications
6.1 Supported Input Formats
Resolution DVI /
HDMI™
480i/576i
480p/576p
720p@(60/50)
1080i@(60/50)
1080p@(60/50)
VGA@(60/72/75/85)
SVGA@(56/60/72/75/85)
XGA@(60/70/75/85)
SXGA@(60/75/85)
UXGA@60
WXGA@60(1280X800)
WXGA+(1440x900)
SXGA+(1400x1050)
WSXGA@60(1680X1050)
WUXGA@60(1920X1200)
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
6.2 Available Output Formats
Resolution DVI /
480i/576i
480p/576p
720p@(60/50)
1080i@(60/50)
1080p@(60/50)
VGA@60
SVGA@@60
XGA@@60
SXGA@@60
UXGA@60
WXGA@60(1280X800)
WXGA+(1440x900)
SXGA+(1400x1050)
WSXGA@60(1680X1050)
WUXGA@60(1920X1200)
Dimensions: 8.24 inch (Wide) x 5.63 inch (Deep) x 1.66 inch (High)
Weight: 2 Pounds (910 g)
Input Power: 90 ~ 264 VAC, 50 ~ 60 Hz (7.5 watts max)
VGA
(PC)
9
9
9
9
9
9
9
9
9
9
9
9
9
9
HDMI™
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
YPbPr
9
9
9
9
9
18
Page 21
Multi Input Digital Scaler with Audio
19
Page 22
Model SC1080-H
20
Page 23
Page 24
©
Copyright 2009. Hall Research Inc.
All rights reserved.
1163 Warner Ave., Tustin, CA 92780
Ph: (714)641-6607, Fax: (714)641-6698
Loading...