Hallowell 400, 800, 435, 425, 455 Assembly Instructions/parts Manual

HALLOWELL® 400/800 SERIES CABINET

Assembly Instructions / Parts Manual

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE BEGINNING CABINET ASSEMBLY.

Retain instructions for future reference.

Description

Hallowell storage, wardrobe and combination cabinets are designed to provide secure store
for office supplies, books, tools, office machines, etc. in offices, schools, institutions
business and industrial store rooms.

The cabinet handle is supplied with built-in lock and two keys. The 3-point locking system
has locks bars located in nylon guides for quiet operation.

Model 415/425/815/825: Storage Cabinet with 4 adjustable shelves
Model 435/445/835/845: Wardrobe Cabinet with one hat shelf and a full width coat rod
Model 455/465/855/865: Combination Cabinet with one hat shelf, center partition, 3 half
width adjustable shelves and half width coat rod

Overall Dimensions

Models 415, 435, 455 are 72” high by 36” wide by 18” or 24” deep
Models 425, 445, 465 are 72” high by 48” wide by 18” or 24” deep
Models 815, 835, 855 are 78” high by 36” wide by 18” or 24” deep
Models 825, 845, 865 are 78” high by 48” wide by 18” or 24” deep

General

1. Check material received against the packing list. First, check the number of packages
received and then check the contents of each package.

2. Check the material received for damage. If damage occurred, secure a “damage notation”
from the carrier.

3. Identify each part as it is unpacked and put like parts together as soon as possible to the
working area where they are to be assembled.

4. Be careful to use the correct hardware as specified in assembly.

[e-mail]

www.Hallowell-List.com

866-566-0500

Assembly Instructions (All Models)

Tools Required: 3/8” nut driver, slotted screwdriver, rubber mallet.

Do NOT fully tighten bolts until cabinet is completely assembled.

1. Place rear panel (item 5) on either padded horses or on protected floor with flanges

upward.

2. Attach side panels (items 7) with the flange under the rear panel offset with 10-24x3/8”

bolts and nuts. The bottom support strips should be at the same end and shelf
adjustment strips pointed in the same direction.

3. Place a shelf (item 8) into shelf adjustment strips to hold sides in upright position while

attach top (item 6).

4. Place door frame assembly (items 1, 2, 3) on top of assembly and bolt to top and side

panels.

5. Position bottom (item 4) into offset support strips on sides and rear. Front flange of

bottom must fit over front flange of frame and be bolted with 2 bolts for the outside
(tighten).

6. If model 455/465/855/865, install center divider (item 11 fig. 3) tighten bolt to bottom.

7. Bolt (4) cabinet foot plates (items 13) to frame and sides and rear (tighten). All models.

Skip this step for mobile cabinets.

8. Stand cabinet upright, be sure cabinet is level and doors close properly and then

tighten all bolts.

9. Insert one side of adjustable shelf (item 8 or 12) at desired position then move other

side up to the same position. If model 435/445/835/845, bolt one coat rod holder (item
10B) inside the flange of shelf with bolt heads outward. Slide rod (item 9 or 10A) into
place, place second rod holder on opposite end of rod and then bolt second rod holder
to shelf. Insert in top location. Seat all shelves with mallet.

10. Using rubber mallet, tap nylon rod guide (item 15) into top and bottom flanges of right

door (item 2).

11. Install turn handle (item 14) to right door with #8-32 bolts (item 19) through handle plate

(item 21) – reference door handle detail. Place lock cam (item 17) on back of handle
with pins out. Insert lock rods (item 16) into rod guides and position holes in lock rods
on pins of lock cam. Secure in place with cam keeper (item 18) using hitch pin clip
(item 20).

12. For mobile cabinets only, attach two casters to each of two caster plates and then

attach caster plates to cabinet bottom (see Caster Kit detail).