Hall HT-VOYAGER Users Guide

Page 1
Hall Technologies • 1234 Lakeshore Dr Suite #150 Coppell, TX 75019 • halltechav.com
Quick Start Guide
Version: 1.0
HT-Voyager
USB Type-C Screen Transmitter Wireless Dongle
Hall Technologies September 1, 2022 Page 1 of 7
Page 2
Introduction
This product is a USB Type-C screen transmitter wireless dongle. It supports sharing contents from screen sources (e.g., laptop) to a display device wirelessly through Hall Technologies Specified AV equipment. It supports transmitting up to 1080P video signal with audio and supports touch back-post feature when sink display is a touch screen.
The device also supports plug and play, and is fully compatible with most operating systems, including Window7/10/11, Mac OS, Android, Linux.
Features
! Supports wireless transmission of video up to 1080P@30Hz with low latency.
! Plug and play, no installation, and no driver needed.
! Quick and simple, just press the button to transmit video, audio, and touch signals.
! Supports 5G and 2.4G frequency bands.
! Low power consumption with strong signal transmission strength to meet requirements in
small to large meeting room scenarios.
! Compatible with main-stream operating systems, like Window7/10/11, Android OS, Mac OS.
Package Contents
! 1 x USB Dongle
! 1 x User Manual
Page 3
Panel Description
No.
Name
Description
1
USB Type-C Port
Connect to Hall Technologies Specified AV equipment for pairing, or source device with USB Type-C port (Support DP) for
projecting screen.
2
Freezing Button
Press the button to freeze/unfreeze the projected screen (the frame on source device is not affected). Note: When freezing/unfreezing the projected screen, the audio projected through the Dongle will also freeze/unfreeze.
3
Projecting Button
Short Press: Short press the button to project source screen or disconnect projected content. Hold the Button for about 2s: When there are multiple screens (including screen projected through the Dongle) shown on the sink display, hold the button for about 2s, the screen projected through the Dongle will be shown in full screen.
4
LED Indicators
Blinking white:
! When connected to the receiver: The Dongle is being paired
up with the receiver.
! When connected to the computer: The Dongle is preparing
and establishing connection with the receiver.
Solid white dimly lit LED: The Dongle is projecting to the screen. Solid on white:
! When connected to the receiver: USB Dongle is paired up with
1
3
4
2
!
Page 4
No.
Name
Description
the receiver successfully.
! When connected to the computer: USB Dongle is connected
to the receiver successfully. You can press the button to start screen projection now.
Application
HT-Voyager Dongle
1. Pair the USB Dongle with Hall Technologies Specified AV equipment. Note: For more detailed operations about the receiver, please refer to its user manual.
a. Connect the USB Dongle to Hall Technologies Specified AV equipment for pairing up. b. Then “Starting pairing…” will appear on the display screen connected to the receiver. The
Dongle’s LED will be blinking. Once pairing is done, “Pairing succeeded” will appear on the display screen. The Dongle’s LED will be solid on.
HT-ODYSSEY Speakerphone
2. Connect the Dongle to a laptop. After pairing up with the receiver successfully, unplug the Dongle from the receiver and connect it to the USB Type-C port of a laptop, it will start running and connecting to the receiver. Once the Dongle connects to the receiver successfully, the Dongle’s LED stops blinking and turns to be solid on. Note: The USB Type-C port of the laptop to which the Dongle is connected, must support transmission of video and audio.
Hall Technologies September 1, 2022 Page 4 of 7
Page 5
3. Now short press the Projection button, you can project your laptop’s screen to the display
Laptop
Display
Dongle
Display
HT-Voyager Dongle
screen immediately. The LED will light dimly white during the projection.
HT-ODYSSEY Speakerphone
! Enter full screen mode: When there are multiple screens (including screen projected
through the Dongle) shown on the sink display, hold projection button for about 2 seconds, you can have your laptop’s screen displayed in full screen.
! Freezing the projected screen: Press the Freezing button, the screen projected by the
Dongle on the sink display will be frozen and the audio projected through Dongle is also paused. A transparent pause icon will appear on the center of the projected screen. Press the button again, the screen will be unfrozen, the icon will disappear, and the projected screen will be synchronized with the source device to display.
Note:
! The freezing function doesn’t affect the source device. ! When a touch screen is connected to the receiver, freezing/unfreezing the projected
screen, the USB HID touch signal from the touch screen returned to the source device will be paused/recovered during transmission.
! When the audio output of the sink display is from a different projected screen,
freezing/unfreezing function doesn’t affect the audio output of it.
Hall Technologies September 1, 2022 Page 5 of 7
Page 6
Specifications
Technical
Max Resolution
1080P @ 30fps
Terminal Type
1 x Type-C
Frequency
5GHz (default) and 2.4GHz
Wireless transmission protocol
IEEE 802.11 a/b/g/n, IEEE 802.11ac
Authentication protocol
WPA2-PSK or IEEE 802.1X
USB
Operate System
Windows 7/10/11, Mac OS, Android,
USB Port
USB Type-C Port (USB 2.0)
General
Operating Temperature
0°C to 40°C (32°F to 104°F)
Storage Temperature
-20°C to 70°C (-4°F to 158°F)
Humidity
10% to 90%, non-condensing
ESD Protection
Human-body Model: ±8kV (Air-gap discharge)/ ±4kV (Contact discharge)
Input Voltage
5V (Power over USB)
Power Consumption (Max)
2.2W
Product size (φ x h x l)
68.98mm x 16.4mm x 165.19mm/2.72” x 0.65” x 6.50”
Product Weight
60g/0.13lb (net weight)
Page 7
© Copyright 2022. Hall Technologies
All rights reserved.
!
1234 Lakeshore Drive Suite #150, Coppell, TX 75019
halltechav.com / support@halltechav.com
(714)641-6607
Loading...