Haivision Makito XR Installation Manual

Makito™ XR Encoder Installation Guide

This Installation Guide summarizes the basic steps required to install and configure the Makito XR SD/HD/3G SDI
H.264 Video Encoder (single chassis, as shown below) to stream to your compatible decoding device. Please refer
to the Makito X User’s Guide or the online help (available from the Web Interface) for detailed information.

NOTE We recommend that you familiarize yourself with this Installation Guide before installing your

Makito XR.

The Makito XR is a rugged COTS encoder designed for the most
demanding Intelligence, Surveillance, and Reconnaissance (ISR)
applications and built to match the physical and mission-critical
requirements of Full Motion Video (FMV). The Makito XR High
Profile encoder supports up to four 720p60 HD (in the X4R model)
or two 1080p60 HD/3G inputs (in the X2R model), and can
simultaneously output two H.264 streams, each at different bit
rates. Scaling and frame rate settings can be adjusted on-the-fly.

Applications

Designed for integration on both manned and unmanned platforms, including aerial, naval, and
ground vehicles, the Makito XR is a single Line Replaceable Unit (LRU) that will not require major system upgrades
to existing platform designs. Tested against the highest international standards for ruggedization, including MIL­STD 810G, MIL-STD 1275E and MIL-STD 461F, it can survive shock and vibration from any mobile application,
including law enforcement, military, and underwater vehicles deployed by oil and gas companies.

F@

<Sbe]`Y

;OYWb]F@

623\Q]RS`

HVS-ID-IG-MAKXR-22, Issue 01 Page 1 of 25

2SQ]RS`

Makito XR Installation Guide

Makito XR Physical Characteristics

Makito XR Physical Characteristics

Dimensions 8.5” W x 3.9” H x 6.7” D

Material Aluminum 6061 T651 per SAE AMS-QQ-A-250/11

Weight 6.8 lbs. (3.08 kg)

Finish External: (Option 1) Black anodized, as per MIL-A-8625F, Type 2, Class 2; (Option 2) CARC white

Internal: Machined T651

Makito XR Power Supply Unit Characteristics

Input Voltage 28V DC / 30W (max.) Storage Temperature -51 to 85 deg C from PDD

Input Protection Reverse polarity protection Working Temperature -40 to 71 deg C

Makito XR Product Numbers

S-292E-X2R Dual channel 3G-SDI Makito X Ruggedized with black anodized finish

S-292E-X4R Quad channel HD-SDI Makito X Ruggedized with black anodized finish

S-292E-X2R-W Dual channel 3G-SDI Makito X Ruggedized with white CARC finish

S-292E-X4R-W Quad channel HD-SDI Makito X Ruggedized with white CARC finish

CAUTION We strongly recommend that you install the Makito XR in an enclosure for protection against

weather and other environmental stresses. The ambient temperature inside the enclosure should be
between -40°C and +71°C, and the relative humidity between 0 and 100%. If you have specific questions
regarding the suitability of the Makito XR in your operating environment, please contact Haivision Tech­nical Support.

HVS-ID-IG-MAKXR-22, Issue 01 Page 2 of 25

Makito XR Installation Guide

Before You Begin

Before You Begin

1. Unpack the box and visually inspect the package contents for any evidence of shipping damage. See the

Important Notice document in the box for a list of contents.

2. In addition to the contents of the Makito XR box, you may need to have the following items available:

• Four #10-32 or M5 screws for mounting

• Haivision cabling kits (see “Accessory Product Numbers” on page 5), or your own custom cables (see

“Makito XR Pinouts” on page 5)

• A laptop with web browser, Telnet client, and video player (e.g. VLC)

NOTE Connector drawings, kitting and terminated cabling drawings are available upon request.

3. In order to be able to view the output from the Makito XR, make sure you have a decoding device or video

player that is able to support the UDP Transport Stream format.

NOTE If the Makito XR is to be installed in a remote location (e.g. on a utility pole, or on a mobile plat-

form), we recommend that you follow the instructions in this Installation Guide to perform an initial set­up in a “staging” environment, such as a lab or control center. Once the encoder has been set up and is
demonstrated to be operating normally, you can then move it to the remote location.

CAUTION Before installing the Makito XR, please refer to the section on “Safety Guidelines” in the

Makito X User’s Guide. Only connect the unit to a compatible power source. If an electrical fault occurs,
disconnect the unit and contact Haivision Technical Support. Never try to force the connections when
setting up the system as this may damage the unit.

CAUTION Hot surface. Avoid contact. The chassis can achieve a surface temperature 95°C in poorly

ventilated environments, and may cause personal injury if touched.

ATTENTION Surface chaude. Eviter le contact. Le châssis peut atteindre une température de surface de

95°C dans des environnements mal ventilés et peut causer des blessures en cas de contact.

WARNING This unit is intended for installation in restricted access areas. A restricted access area can

be accessed only through the use of a special tool, lock and key, or other means of security.

AVERTISSEMENT Ce produit est destiné à être installé dans une zone d'accès restreint. Les zones d'accès

limité sont protégées par un mécanisme spécifique, une serrure et une clé ou tout autre dispositif de sé­curité.

NOTE While the Makito XR has a real-time clock (RTC), it has no RTC battery. In the event of a power loss,

the system date and time settings are lost. For any application with a requirement for standalone syn­chronized system timing (or derived time codes), an NTP server should be used to provide time and date
synchronization. Refer to the Makito X User’s Guide for details.

HVS-ID-IG-MAKXR-22, Issue 01 Page 3 of 25

Installing the Makito XR

1. Position the appliance against a solid base.

CAUTION The surface temperature of the chassis can reach 95°C in poorly ventilated environments. We

recommend that you fasten the appliance to a metal (cold) plate to increase heat dissipation.

2. Fasten the appliance to its support base with four screws (size 10-32, or M5).

Makito XR Installation Guide

Installing the Makito XR

Mounting

hole

Mounting

hole

Mounting
hole

Mounting
hole

3. Fasten a grounding wire (10 AWG minimum) to the grounding lug using the nut and lock washer provided.

Grounding lug with

M5 thread

Power indicator
night-vision LED

(green = power on)

CAUTION The chassis must be properly grounded in order to provide protection against lightning

strikes and other power surges.

HVS-ID-IG-MAKXR-22, Issue 01 Page 4 of 25

Encoder status
night-vision LED
(bi-color: green or yellow)

Ref: TIID-031 Rev. C-

Makito XR Installation Guide

J3

Accessory Product Numbers

Accessory Product Numbers

CA-292E-XR-CONNSET MIL-STD connector set (power, video, Ethernet/serial) — J1 to J5

CA-292E-XR-TERMSET Commercial break-out connectors terminated cable set (Ethernet = RJ45, serial=DB9,

4-input audio, video BNC, power) with MIL-STD connectors

P-292E-XR-PS Power supply for the XR unit — 120/240 AC to +28V DC (40 Watts) with locking

connector

Makito XR Pinouts

The J1 to J4 connectors on the Makito XR are GLENAIR 38999 series shells. J5 is a MIL-DTL-38999 matched
impedance connector. The coaxial pins are GLENAIR 852-056-02. For detailed pinout information see “Appendix

A: Makito XR Encoder Pinouts”.

J1 J2

J4 J5

NOTE Connector drawings, kitting and terminated cabling drawings are available upon request. Contact

Haivision Technical Support

HVS-ID-IG-MAKXR-22, Issue 01 Page 5 of 25

Connecting the Makito XR to the Network and Video Sources

Connecting the Makito XR to the Network and Video Sources

1. Connect video, serial and network cables, referring to the images below:

Makito XR

Makito XR Installation Guide

J2 — Maintenance

connector (serial,

USB, and reset)

J1 — Power connector

LED1 — Power status

J3 — Future use

J4 — I/O connector for network commu-

nications (stream output; web interface)

J5 — Connector for video input

(including metadata)

LED2 — Video

encoder card status

2. Remove the protective caps from the Makito XR’s connectors

3. Connect the Makito XR’s J4 port to the IP network using the Ethernet cable:

RJ-45

4. (Optional) Connect the Makito XR’s J2 port to a metadata source or to the serial port of a computer using the

maintenance breakout cable (shown following).

HVS-ID-IG-MAKXR-22, Issue 01 Page 6 of 25

Connecting the Makito XR to the Network and Video Sources

Makito XR Installation Guide

J2

NOTE The reset button provides two options:

• If you press and hold the button for less than 4 seconds the system resets and load loads the last

saved configuration. If no configuration was previously saved, the default settings prevail.

• If you press and hold the button for more than 4 seconds, the module performs a complete factory

reset. It clears all of the previously configured settings, including IP, streams and encoder
configurations.

5. Connect the Makito XR’s J5 port to your video source(s) using the video breakout cable.

DB-9
RS-232/422

USB 2.0
(Future use)

System
Reset

NOTE The Makito XR supports up to 2 video inputs @ 1080p50/59.94/60 (in the X2R model), or up to 4

video inputs @ 1080p25/29.97/30 (in the X4R model).

6. Power up the unit. Note that there is no power switch on the Makito XR appliance. The power is

automatically on when the unit is plugged in.

CAUTION The power cord is used as the main disconnect device. Ensure that the socket-outlet is locat-

ed/installed near the equipment and is easily accessible.

ATTENTION Le cordon d'alimentation est utilisé comme interrupteur général. La prise de courant doit

être située ou installée à proximité de l'équipement et être facile d'accès.

• Insert the 3-pin connector of the power cable into the power input jack (J1) at the rear of the encoder.

J1

Mini-BNCJ5

Make sure the connector is properly inserted and locked to avoid intermittent power problems.

• Connect the power cable to a 28V power source (the P-292E-VR-B PSU can be used to convert from
+120V AC to +28V DC).

HVS-ID-IG-MAKXR-22, Issue 01 Page 7 of 25

Connecting the Makito XR to the Network and Video Sources

Makito XR Installation Guide

• The Status LED next to J5 will start blinking green, indicating that the encoder is booting up.

• Wait until the Status LED stays solid green, indicating that the encoder is ready for operation.

NOTE The Makito XR performs Built-in Self Tests (BIST) and Power-On Self Tests (POST) to ensure that the

hardware and firmware are operating reliably and correctly. BIST provides a minimal suite of tests that
test the various hardware and firmware sub-systems to ensure correct operation. The POST suite of tests
(a subset of the BIST suite) are performed every time there is a power-cycle. All BIST/POST configuration,
status and test results are available via CLI (serial, Telnet or SSH). For more information, please refer to
the Makito X User’s Guide.

HVS-ID-IG-MAKXR-22, Issue 01 Page 8 of 25

Modifying the Makito XR’s IP Address

Makito XR Installation Guide

Modifying the Makito XR’s IP Address

If you haven't changed the factory presets, and if not specified elsewhere in the shipment, the encoder’s IP
address is set by default to: 10.5.1.2. To be able to log in to the Makito XR Web interface, your computer has
to be in the same IP address range (subnet). You may have to temporarily change your computer’s IP address to
be in the same subnet as the encoder. Only then will you be able to access the encoder and change its IP address,
and then afterwards change your computer's IP address back.

TIP After you change the Makito XR encoder’s IP address, we recommend that you document it some-

where, and label the chassis.

1. If you have not already done so, power up the Makito XR.

2. The Makito XR comes pre-configured with the following settings:

IP Address* Subnet Mask Gateway

10.5.1.2 255.255.0.0 10.5.0.1

* The IP address of your computer must be in the same subnet.

3. Open a Web browser, type the IP Address for the Makito XR into the URL address bar, and press Enter.

4. Log in to the Makito XR Web Interface, using the following default administrative username and password:

Admin Username Password*

admin manager

* Be sure to change the default password.

NOTE While the Web interface is most commonly used to control the Makito XR, a Command Line Inter-

face (CLI) is accessible via Telnet or SSH. For more information, please refer to the Makito X User’s Guide.

HVS-ID-IG-MAKXR-22, Issue 01 Page 9 of 25

Modifying the Makito XR’s IP Address

Makito XR Installation Guide

5. Select the ADMINISTRATION icon from the toolbar, and then select NETWORK (under SETTINGS).

6. Type in the new IP address. If required, select or enter other new value(s) in the appropriate field(s).

7. To apply your changes, click Apply, and then click Reboot. (You must reboot the system for the changes to

take effect.)

NOTE Remember to change your computer network settings to be on the same network segment as the

Makito XR.

HVS-ID-IG-MAKXR-22, Issue 01 Page 10 of 25

Makito XR Installation Guide

Setting up a Test Stream

Setting up a Test Stream

Setting up a test stream requires that you have an active video source connected to the Makito XR. You will need
to configure an encoding instance based on your video source, and then configure an output stream for that
encoder. For detailed information, please refer to Chapter 4 of the Makito X User’s Guide.

1. If you have not already done so, power up the Makito XR.

2. Open a Web browser, type the IP Address* for the Makito XR into the URL address bar, and press Enter.

* The IP address of your computer must be in the same subnet (see “Modifying the Makito XR’s IP Address”
on page 9).

3. Click the

STREAMING icon on the toolbar, and then click VIDEO ENCODERS from the sidebar menu.

The Video Encoders List View opens, as shown in the following example.

4. From the Video Encoders List View, click a link in the table to select the encoder.

HVS-ID-IG-MAKXR-22, Issue 01 Page 11 of 25

Click link to open Detail View

Makito XR Installation Guide

Setting up a Test Stream

The Video Encoder Detail View opens, displaying the settings for the selected video encoder (see following
example).

5. Select or enter the new value(s) in the appropriate field(s).

6. Click

7. Click the

Start, and then click Apply.

STREAMING icon on the toolbar, and then click OUTPUTS from the sidebar menu.

The Output Streams List View opens, as shown in the following example.

HVS-ID-IG-MAKXR-22, Issue 01 Page 12 of 25

8. To add an output stream, click Add.

The Output Streams Detail View opens (as shown in the following example for a new stream).

Makito XR Installation Guide

Setting up a Test Stream

9. Type a Name for the stream and select TS over UDP for the Protocol.

10. In the Source section, select the encoder you started in step 6. from the Video menu.

11. In the Destination section, type in a valid multicast Address (e.g. 239.192.2.3) and Port number (e.g.

2000).

NOTE The Multicast address range is from 224.0.0.0 to 239.255.255.255. Multicast addresses from

224.0.0.0 to 224.0.0.255 are reserved for multicast maintenance protocols and should not be used

by streaming sessions. We recommend that you use a multicast address from the Organization-Local
scope (239.192.0.0/14).

HVS-ID-IG-MAKXR-22, Issue 01 Page 13 of 25

Makito XR Installation Guide

Viewing the Test Stream

12. To add metadata to the stream, select the Metadata source, and (optionally) select the encapsulation type

(Data Carriage).

13. To apply your changes and start streaming, click

Apply.

The changes will take effect immediately but will be lost after a reboot. For information on saving configura­tion settings, please refer to the “Saving and Loading Presets” section of the Makito X User’s Guide.

Viewing the Test Stream

1. Make sure your decoding device (or software) is compatible with the UDP Transport Stream format.

2. Turn the device on and connect it to a display (if applicable), or open your video player software (e.g. VLC).

3. Make sure you are on the same network segment as the Makito XR, and

4. Tune your decoding device or software to the multicast address of the test stream coming from the Makito

XR.

HVS-ID-IG-MAKXR-22, Issue 01 Page 14 of 25

Makito XR Installation Guide

Abbreviations & Definitions

Appendix A: Makito XR Encoder Pinouts

This appendix contains the pinout descriptions for the Makito XR SD/HD/3G SDI H.264 Video Encoder. This
information must be used in conjunction with Haivision drawing no. TIID-031 (Makito XR Enclosure External Cable
Connections).

Abbreviations & Definitions

EMC Electromagnetic Compatibility

ESD Electro Static Discharge

GBE Gigabit Ethernet per IEEE 802.3ab (same as 1000BASE-T)

GPIO General Purpose Input/Output

HDA High Definition Audio (Intel standard)

I2C Two-wire Serial Interface

NC No Connect

PCB Printed Circuit Board

p/n Part Number

SCD Source Controlled Drawing / Source Controlled Document

SDI Serial Data Interface (governed by SMPTE standards)

SKU Stock Keeping Unit

TBD To be determined

USB Universal Serial Bus

References

For additional information, please refer to the following documents:

• Makito XR External Cable Connections (TIID-034)

• Makito XR Data Sheet

• Makito X User’s Guide

• SMPTE 259M (SD-SDI), 292M (HD-SDI) and 424M (3G-SDI)

• IEEE 802.3-2012 (Ethernet)

• USB standard, USB Implementers Forum (USB.org)

• High Definition Audio (HDA) codec specification (Rev.1.0a), Intel

HVS-ID-IG-MAKXR-22, Issue 01 Page 15 of 25

Makito XR Installation Guide

Enclosure Front Panel

Enclosure Front Panel

The Makito XR video encoder enclosure offers total of 5 MIL-STD connectors for external cables attachment.

Makito XR Video Encoder Enclosure Front View

ID Description Number of Contacts

J1 Power Connector 3

J2 Maintenance Connector 26

J3 Future use 85

J4 Ethernet 85

J5 Video Input Connector 4 pins (coaxial, 75-ohm)

ID Description Location

LED1 Power Status Near J1

LED2 Video Encoder Card Status Near J5

Connector Part Numbers

J1 to J4 are GLENAIR 38999 series shells.

List of Connectors

List of LED Indicators

J5 is a MIL-DTL-38999 matched impedance connector that accommodates 4 pin contacts, size 8, with 75-ohm
impedance. The coaxial pins are GLENAIR 852-056-02

Refer to Haivision drawings TIID-031 and TIID-034 for detailed list of part numbers.

HVS-ID-IG-MAKXR-22, Issue 01 Page 16 of 25

Power Entry Connector (J1)

Refer to the Makito XR video encoder data sheet for power requirements details.

Power Connector J1

Manufacturer GLENAIR

Connector Type MIL-DTL-38999

Part Number 805-004-07ZNU8-23PA

Front Connector Power Location

Connector Pin Description

Makito XR Installation Guide

Power Entry Connector (J1)

J1 1 28 Volt Input – 1.0A max

J1 2 28 Volt Return

J1 3 Chassis Ground

J1 Power Connector Pin Locations

HVS-ID-IG-MAKXR-22, Issue 01 Page 17 of 25

Maintenance Connector (J2)

I/O Connector: J2

Manufacturer GLENAIR

Connector Type MIL-DTL-38999

Part Number 805-005-07 ZNU 12-26SA

Feature Reference

USB 2.0 interface Refer to “USB 2.0 Interface”

RS-232 serial interface Refer to “RS-232 Serial Interface”

Reset Button Refer to “Reset Button”

Makito XR Installation Guide

Maintenance Connector (J2)

USB 2.0 Interface

The Makito XR video encoder has a USB 2.0 Host Interface which is provisioned for future use applications. It is
currently disabled.

Do not attach a USB device requiring more than 500 mA.

Front Connector View I/O Location

Connector Pin Description

J2 11 USB7_GND signal

14 USB7 Drain Wire – Cable shield SH - Shield

15 USB7 5V - Always enabled 500 mA Max

18 USB7_D+ Data signal ESD Protected ± 8 kV

23 USB7_D- Data signal ESD Protected ± 8 kV

All Others Not Connected (NC)

HVS-ID-IG-MAKXR-22, Issue 01 Page 18 of 25

J2 Maintenance Connector USB Pin Locations

Makito XR Installation Guide

RS-232 Serial Interface

RS-232 Serial Interface

Makito XR video encoder can be managed through a RS-232 serial interface, one commonly used for configuration
making use of the Command Line Interface (CLI). This port is designated as COM1.

Front Connector View I/O Location

Connector Pin Description

J2 1 COM1 – Drain Wire / Cable Shield SH

3 COM1 – RX RS-232 Receive Data

signal

6 COM1 – TX RS-232 Transmit Data

signal

8 COM1 – RS-232 Ground signal

RX1 ESD Protected ± 18 kV

TX1 ESD Protected ± 18 kV

HVS-ID-IG-MAKXR-22, Issue 01 Page 19 of 25

Makito XR Installation Guide

Reset Button

J2 Maintenance Connector COM1 – Module RS-232 Pin Locations

Reset Button

A reset button (RST# signal) can be asserted to ground to provide the user with 2 options.

• If RST is asserted for 0s < t < 4s duration, the system resets and loads the last saved configuration. If no

configuration was previously saved, the default settings prevail.

• For assertion of t > 4s, the module performs a complete factory reset. It clears all of the previously configured

settings, including IP, streams and encoder configuration.

Front Connector I/O Location

Connector Pin Description

J2 19 System Reset Ground

24 System Reset Signal – asserted LOW RST# 3.3V Input

ESD Protected ± 18 kV

HVS-ID-IG-MAKXR-22, Issue 01 Page 20 of 25

Makito XR Installation Guide

Connector (J3)

J2 Maintenance Connector MISC Signal Pin Locations

Connector (J3)

This connector is reserved for future use.

HVS-ID-IG-MAKXR-22, Issue 01 Page 21 of 25

Ethernet (J4)

I/O Connector: J4

Manufacturer GLENAIR

Connector Type MIL-DTL-38999

Part Number 0805-005-07M19-85SD

Feature Reference

GBE0 — Ethernet Refer to “GBE0 — Ethernet”

Makito XR Installation Guide

Ethernet (J4)

GBE0 — Ethernet

The Makito XR video encoder allows for connectivity with one 10/100/1000 Gigabit Ethernet port over CAT-5
unshielded twisted pair per IEEE 802.3ab. The naming convention is per IEEE STD 802.3. This port is designated as
GBE0.

Front Connector View I/O Location

Connector Pin Description

J4 4 Ethernet Data Signal GBE0_BI_DB+ 1+ ESD Protected ± 8 kV

9 Ethernet Data Signal GBE0_BI_DB- 1-

18 Ethernet Data Signal GBE0_BI_DD- 3-

19 Ethernet Data Signal GBE0_BI_DD+ 3+

25 Ethernet Data Signal GBE0_BI_DA- 0-

26 Drain Wire – Ethernet Shield SH

35 Ethernet Data Signal GBE0_BI_DA+ 0+

37 Ethernet Data Signal GBE0_BI_DC- 2-

38 Ethernet Data Signal GBE0_BI_DC+ 2+

HVS-ID-IG-MAKXR-22, Issue 01 Page 22 of 25

Makito XR Installation Guide

GBE0 — Ethernet

J4 Ethernet GBE0 Pin Locations

HVS-ID-IG-MAKXR-22, Issue 01 Page 23 of 25

Makito XR Installation Guide

Video Connector (J5)

Video Connector (J5)

The Makito XR video encoder allows up to four SDI / Composite video inputs, both signals sharing the contact pin.

• SDI is governed by SMPTE 259M (SD-SDI), 292M (HD-SDI) and 424M (3G-SDI) standards. Each coaxial pin is 75-

ohm impedance (3-GHz bandwidth).

• Composite video allows for NTSC and PAL input signals among others.

Refer to the product specification for complete details.

I/O Connector: J5

Manufacturer GLENAIR

Connector Type Video Quad Coax Plugs

Part Number SHELL : 257-606ZR07-21Q-75AN

PINS : 852-056-02

Front Connector I/O Location

Connector Pin Description

J5 A Video Input BNC 1 ESD Protected ± 8 kV

B Video Input BNC 2

C Video Input BNC 3

D Video Input BNC 4

HVS-ID-IG-MAKXR-22, Issue 01 Page 24 of 25

J5 Video Input Pin Locations

Makito XR Installation Guide

For More Information

For More Information

Contact Haivision Technical Support via our Support Portal on our website at: https://support.haivision.com

Or you may use the phone numbers or email addresses listed below:

North America:

International:

Toll Free: 1.877.224.5445 (option 4)

Tel: [phone] (option 4)
Fax: [phone]

Technical Support email:

Product Information email:

[e-mail]

[e-mail]

You may download the latest software, Release Notes and other relevant documentation through our Download
Center at: https://support.haivision.com

Waste Electrical and Electronic Equipment (WEEE) Disposal

Haivision is compliant with the European Union (EU) WEEE Directive. For recovery and recycling
information, please visit our website at:

http://www.haivision.com/environment

HVS-ID-IG-MAKXR-22, Issue 01 Page 25 of 25