HDMI Extender Over HDBase-T
User Manual
EXHA10R
Full 3D Pass-through
Support IR Control
Ultra HD 4K x 2K
100M Solution
INTRODUCTION
•1 x HDMI Transmitter unit, 1x HDMI Receiver unit
•2 x 5V DC power supply
•1 x User Manual
•HDMI, HDCP 1.2 and DVI Compliant
•Support full 3D pass-through
•Support 4k x 2k high resolution
•Super IR control system, IR transport channel can be forward or backward
per your installation
•100M extension with a Cat5e/6/7 over HDBase-T technology
•Support CEC bypass
•External and internal EDID settings
FEATURES
PACKAGE CONTENTS
This HDMI HDBase-T extender uses single CAT-5E/6/7 cable to extend 3D
TV over 100m away from the source. It supports resolutions up to 4k x 2k
full HD and high bit-rate audio formats such as Dolby True-HD and DTS-HD
Master Audio. Support IR control system, IR transport channel can be forward
or backward, an IR blaster and receiver pigtails are needed.
By using standard CAT6 cable(recommended), it makes HDMI signal
extension easier to install within a room or through walls. The Extender’s
digital transmission uncompressed method insures 100% signal integrity.
PANEL DESCRIPTION
Transmitter Unit
Receiver Unit
HDCP Link Mode Power
IR-RX IR-TX
1 3 5 6
2 4
7 8 9
10
1 HDCP LED INDICATOR
2 LINK LED INDICATOR
3 MODE LED INDICATOR
4 POWER LED INDICATOR
5 IR RX PORT
6 IR TX PORT
7 POWER SUPPLY INPUT
8 HDBase-T OUTPUT
9 HDMI INPUT
10 NETWORK PORT
Front Panel Rear Panel
1 HDCP LED INDICATOR
2 LINK LED INDICATOR
3 MODE LED INDICATOR
4 POWER LED INDICATOR
5 IR RX PORT
6 IR TX PORT
7 POWER SUPPLY INPUT
8 HDBase-T INPUT
9 HDMI OUTPUT
10 NETWORK PORT
HDCP Link Mode Power
IR-RX IR-TX
1 3 5 6
2 4
7 8 9
10
Front Panel Rear Panel
NOTE
•The HDCP LED will illuminate in green when the input source signal contains
HDCP data.
•The LINK LED will illuminate in green when both the Transmitter and Receiver
are properly connected and data is being transmitted/received.
•The MODE LED will flash in green when the device is processing data.
•The POWER LED will be in red when power is on.
DC 5V
HDBase-T
HDMI IN
100Base-T
100Base-T
DC 5V
HDBase-T
HDMI IN
100Base-T 100Base-T
INSTALLATION
CONNECTION DIAGRAM
•Connect HDMI input port on transmitter to the signal source equipment
such as DVD player.
•Connect the HDBase-T output of the transmitter with a CAT5e/6/7 cable
to the HDBase-T input of the receiver.
•Connect one of the network input with a Cat5e/6/7 cable to a router and
the rest three as output for PC for online use.
•Connect IR blaster cable (not included in the package) for signal transmission.
Place the IR blaster in direct line-of-sight of the equipment to be controlled.
•Plug the 5VDC power supply into the unit and connect the adaptor to
AC outlet.
•Connect the HDMI output of the receiver to the displays.
•Connect IR receiver cable (not included in the package) for signal reception.
Place the IR receiver indirect line-of-sight of remote.
•Plug the 5VDC power supply into the unit and connect the adaptor to
AC outlet.
DC 5V
100 M Extension Over HDBase-T
DC 5V
HDBase-T
08：08
PLAY
DC 5V
HDBase-T 100Base-T
100Base-T
HDMI IN
HDCPLinkModePower
IR-RXIR-TX
DC 5V
HDBase-T 100Base-T
100Base-T
HDMI IN
HDCPLinkModePower
IR-RXIR-TX
Router
SPECIFICATION
Transmitter
Input Port
Output Port
Receiver
Input Port
Output Port
Bandwidth
Output Resolution
Operating Temperature
Deep Color
Chassis
Dimension
Weight
Power Supply
1 x HDMI (Female Connector)
2 x IR Channels, 1 x HDBase-T,
2 x Network RJ45 Jack
2 x IR Channels, 1 x HDBase-T,
2 x Network RJ45 Jack
1 x HDMI (Female Connector)
10.2Gbps
480i~1080P@50/60,1080P@24/50/60,
VGA~UXGA
-15℃~55℃/5°F~131°F
36bit
Metal
83mm(L)x46mm(W)x22mm(H)
465g
DC 5V
Please read the following safety precautions carefully before you unpack
and install this equipment.
1.Do not expose the unit to rain, moisture or any other dripping liquids. And
keep it away from any wet locations such as fishing tanks, vases.
2.Do not install the unit close to fire or any other heat sources.
3.Keep the unit in dry and ventilated area. Do not install in bookcase,
cabinet or any other confined space.
4.Stop using the unit during thundering or lightening storms.
5.Avoid the power cable to be stepped on or pinched. Position the unit
carefully to avoid damage or accident.
6.Clean the unit only with dry cloth.
7.Only use accessories specified by the manufacturer.
8.Unplug the equipment when unused for a long period of time.
9.Do not try to open any non-serviceable parts. Contact your authorized
servicing center and personnel.
SAFETY PRECAUTIONS
Tel:+86 769 81877098
Fax:+86 769 81877138
Email:chinasales@hailink.cn
Http:www.hailink.cn
Danger Electric
Shock Risk
Keep Dry
Keep Away
from Heat
Loading...