Haier YR-E17 Operation & Installation Manual
Wired Controller
Operation & Installation Manual
• Please read this operation manual before using the air conditioner.
• Please keep this manual carefully and safely.
CONTENT
Parts and Functions............................................................ 1
Operation ............................................................................ 9
Wired Controller Wiring Instruction ................................... 46
YR-E17
1
Interface Display
Parts and Functions
2
ON/OFF
Adjusting key for temperature, clock, timer, sleeping
adjustment, temp. compensation and energy saving;
Inquiring key for detail parameter and malfunction inquiry;
Switching key for function switch.
The adjusting accuracy of temperature is 0.5°C (1°F). If energy
saving mode is not set, the adjusting range is from 16°C
(60°F) to 30°C (86°F). If energy saving mode is set, the lowest
temperature limit of cooling/dry and the highest temperature
limit of heating are decided by the setting of the chip, the
default cooling/dry temperature is 23°C (74°F), and the default
heating temperature is 26°C (78°F).
Note:
• If the dip switch Sw2 is “on”, it displays the ambient temp., as
well as when powered off. From power off to power on, mode
switching and set temp. adjustment, it ashes to display SET
icon and statically displays the set temp.. And then statically
displays the ambient temp. and ROOM icon after 3 seconds.
In energy saving mode and temp. compensation mode, the
adjusting step is 1°C (1°F) a time.
Key
Parts and Functions
3
• If using Fresh Air unit, set temp. cannot be adjusted. If there
is no Central/Lock set, the temp. will be xed at 18°C (64°F)
in cooling and 22°C (72°F) in heating. The Up/Down key will
not display in normal state, but will display and valid in timer
setting, function selection, unit shift in malfunction inquiry,
parameter shift in parameter check, unit No. setting, sleeping
time adjustment, etc.
24-hour, press once to minus one minute. Keep pressing,
minus 2 minutes in 1 second’s pressing, then 10 minutes
in 5 seconds. The time will keep decreasing at the pace of
10 minutes a time in 10 seconds. Vice-versa. Press
to
conrm or it will turn back to the previous state automatically in
10s.
Parts and Functions
Press this key to execute mode switch. For detailed
information, please refer to mode setting.
Note: If using Fresh Air unit, default 3 modes will circulate from
cooling→heating→fan→cooling.
4
Pressing this key, fan speed will be changed in sequence as
follows:
(Low) → (Medium)
→
(High)→
(
Auto) →
(Low)
Note: Auto fan will be changed in sequence as follows:
→ →
→
Pressing this key, fan speed will be changed in sequence as
follows (Only valid for parts of models):
(Breeze) → (Low) →
(Medium) →
(High) →
(Super) →
(Auto) → (Breeze)
Auto fan circulation:
(Breeze) → (Low) →
(Medium) →
(High) →
(Super)
There is no auto fan in fan mode; The fan icon will ash when
adjusting the fan speed. It will statically display after the
adjustment.
Parts and Functions
5
Timer ON, Timer OFF, Timer ON/OFF.
Press this key to enter function circulation. If it is the fourway cassette model, press Set key for 5s to enter function
circulation.
1.Press
to select the functions in sequence as follows:
(Only when Left/Right swing is valid) → (Only when Up/
Down swing is valid) →
→ (ventilation function) →
(reserved function) →
(When it’s time for lter cleaning,
this icon will involve in circulation) →
(the second 8 of
88.8 in the temp. display area displaying A,only valid for part
of models)→
(the second 8 of 88.8 in the temp. display
area displaying B,only valid for part of models)→
(motion
sensing,only valid for part of models) →10°C heating function
(this function only works in the heating mode, only valid for
part of models) → health airow up (Only valid for part of
models) → health airow down (Only valid for part of models)
Parts and Functions
Note: If using Fresh Air unit, fan will be in auto fan and cannot
be adjusted. If press FAN key, fan icon and FFFF on the
top-right corner will ash, prompting fan speed cannot be
adjusted, and will statically display after 3s. Fresh Air unit fan
speed will be controlled automatically by indoor unit and wired
controller will always display auto fan.
6
2.Press
to select the functions in sequence as follows:
health airow down (Only valid for part of models) → health
airow up (Only valid for part of models) →10°C heating
function (this function only works in the heating mode, only
valid for part of models) →
(motion sensing,only valid
for part of models) →
(the second 8 of 88.8 in the temp.
display area displaying B,only valid for part of models) →
(the second 8 of 88.8 in the temp. display area displaying
A,only valid for part of models) →
(When it’s time for lter
cleaning, this icon will involve in circulation) →
(reserved
function) →
(ventilation function) → → (Only when
Up/Down swing is valid) →
(Only when Left/Right swing is
valid)
3. Press
to conrm function selected. If there is function
selected, press
can cancel this function.
Note: The Left/Right swing
is valid only after the dip switch
is set, the lter icon
is shown only after the lter requires
cleaning.
Parts and Functions
7
Parts and Functions
Icon
Clock; Parameter setting/inquiry; Malfunction
display; Mode setting.
Timer ON/OFF: Sleeping; Parameter setting/
inquiry; Malfunction display.
ROOM/SET temp. and humidity display, each
step is 0.5°C (1°F) . For example, if the temp.
is 25°C (77°F), it will display 25.0°C (77°F).
Humidity display function is reserved.
Energy Saving, This icon will be displayed
only when energy saving function is set.
Filter Cleaning.
Child Lock. This icon will be displayed only
when child lock function is set.
/ Lock/ Central
Motion Sensing (Only valid for part of
models).
Left/Right Swing. This icon is displayed in
swing mode; no display without swing mode.
Up/Down Swing. This icon is displayed in
swing mode; no display without swing mode.
8
Parts and Functions
Sleeping. This icon is displayed when setting the
sleeping, and left time of sleeping is displayed by
Heat Reclaim Ventilation, This icon is displayed when
setting the heat reclaim ventilation.
Electrical Heating. This icon will display when electrical
heating is set on DC wired controller.
Intelligent Mode.
Cooling Mode. Heating Mode.
Fan Mode. Dry Mode.
Breeze Fan Speed (Only
valid for part of models)
Low Fan Speed.
Medium Fan Speed.
High Fan Speed.
Super Fan Speed (Only
valid for part of models)
If the fan speed is set in auto fan, it will change in the
following sequence: Breeze(Only valid for part of models)
→Low→Medium→High→Super (Only valid for part of
models), AUTO icon will display simultaneously.
9
Dip Switch Interpretation (for AC)
Operation
DIP
switch
On/Off
station
Function
Default
setting
Sw1
On Slave wired controller
Off
Off Master wired controller
Sw2
On Ambient temp. display on
Off
Off Ambient temp. display off
Sw3
On
Collect ambient temp. from PCB of
indoor
Off
Off
Collect ambient Temp. from wired
controller
Sw4
On Non-volatile memory invalid
Off
Off Non-volatile memory valid
Sw5
On Old protocol
Off
Off Selfadaption
Sw6
On reserved
Off
Off reserved
Sw7
On
Model with Up/Down and Left/Right
swing
Off
Off Model with Up/Down swing
Sw8
On Fresh Air unit
Off
Off General unit
10
(1)The wired controller will display all the icons after powering
on or reset, then get into the initializing process. The controller
will display in sequence as follows:
(the top-left
corner) →
(the top-right corner) → → (the
top-left corner), the green LED ashes all the time until the
initialization ends.
Initialization
Operation
Difference between the Function of the Master Wired
Controller and Slave Wired Controller
Comparison
item
Master
wired
controller
Slave wired controller
Function
All
functions
are
available
1. ON/OFF, Mode, Fan Speed, Temp.
Setting, Swing, Energy Saving, Clock
function, Heat Reclaim Ventilation
function, Mode Setting, Screen
Saving and Child Lock are available
2.Cancel the lter cleaning icon
3.Look up the detailed parameter and
malfunction code
11
Operation
(1) In the state of off and non screen saving, keep pressing
and for 5s to set screen saving time, which will be
shown after the top-right colon 88 statically. Press Up/Down
key to adjust screen saving time and press
key to conrm.
(2) Screen saving time should be 0s(backlight always on),
15s, 30s, 60s, default value is 15s. If it is not the rst time of
entering, it will display the screen saving time adjusted last
time.
(3) In the process of changing screen saving time, press ON/
OFF key to quit screen saving time setting function, it will
recover to screen saving time before adjustment and start-up
the unit.
Note:
When controlling Fresh Air unit, the controller main interface
will not display Up/Down key in normal state. When in screen
saving setting, press Time key rst to display Up/Down key at
the main interface, and then press together Time and Down
key to enter screen saving time setting.
Screen Saving
(2) If the wired controller can’t be communicated with the
indoor PCB normally after powering on, the initialization will be
nished in 4 minutes, and then the communication malfunction
can be checked from the malfunction inquiry function.
12
Operation
(1) 24-hour system is used, and at rst time of powering on, it
will display default 12:00.
(2) When rst powering on wired controller,
will be
displayed on the wired controller interface, clock time can
be adjusted within 10s. At the same time, clock icon
and
minute-place of time will ash, meaning the current time can
be adjusted. Press Up/Down key to adjust minute-place with
ashing of clock icon and no ashing of minute-place. Press
Time key to shift to hour-place, and then press Up/Down key
to adjust hour-place with ashing of clock icon and no ashing
of hour-place. After adjustment, clock icon and hour-place will
ash and press
key to conrm and clock icon and time
will display statically.
Clock Function
13
Operation
(3) Press Time key for 5s to enter clock setting function. It
will show
after rst powering on (if not rst time of
powering on, clock time is the memorized time), with clock
icon and minute-place ashing, meaning current time can be
adjusted. Press Up/Down key to adjust
minute-place with ashing of clock icon and no ashing of
minute-place. Press Time key to shift to hour-place, and then
press Up/Down key to adjust hour-place with ashing of clock
icon and no ashing of hour-place. After adjustment,
clock icon and hour-place will ash and press
key to
conrm and clock icon and time will display statically.
(4) Clock time adjustment: when adjusting time, press
one
time to reduce one minute/hour while press
one time to add
one minute/hour. Keep pressing
or key to accelerate time
adjustment, with 2 times/s change after 1 s, 10 times/s change
after 5s. After 10s, it will change by 10 minutes and frequency
is 10 times/s.
(5) In the process of time adjustment, if there is no operation
for 10s, it will quit and restore previous state.
(6) In the process of time adjustment, press ON/OFF key to
quit clock setting function and execute turning on/off operation
at the same time.
14
Operation
(7) When setting timer or sleeping function, clock time cannot
be adjusted. If press Time key for 5s to enter clock adjustment,
clock icon and clock time will ash indicating time cannot be
adjusted.
(1) Timer mode setting: Timer ON, Timer OFF, Timer ON/OFF.
(2) Default: Timer ON is
, Timer OFF is .
(3) Precision: The time precision is 1 minute. Timer clock is
based on the current clock time; the adjustment is the same as
clock time.
(4) Screen display: The icon is set to be presented on the topright of the screen.
(5) Relation to the
(ON/OFF): The ON/OFF button has no
affection on timer setting. Under power off state, the Time key
is valid.
(6) Timer display:
Timer ON:
Press
key, it displays default for the rst time
(previous setting will be displayed if there is setting before).
Timer Function
15
Operation
Then hour position and “ON” are ashing. Press to
adjust the timer, minus/add 1 hour a time. Keep pressing to
accelerate the adjusting speed. Press
key a second time
and then the minute position and “ON” are ashing. Press
to conrm the setting, the setting time is displayed and “ON”
will not ash. If there is no input for 10s, this setting will be
cancelled and the timer will come back to the previous state.
Timer OFF:
Press
key, it displays default for the rst time
(previous setting will be displayed if there is setting before).
Then hour position and “ON” are ashing; Press key
again, the minute position and “ON” are ashing; Press
key again, it displays default for the rst time
(previous setting will be displayed if there is setting before).
Then the hour position and “OFF” are ashing. Press to
adjust the timer, minus/add 1 hour a time. Keep pressing to
accelerate the adjusting speed; Press
key again, the
minute position and “OFF” are ashing. Press
to conrm
the setting, the setting time is displayed and “OFF” will not
ash. If there is no input for 10s, this setting will be cancelled
and the timer will come back to the previous state.
Timer ON/OFF:
Press
key, it displays default for the rst time
(previous setting will be displayed if there is setting before).
Loading...