Double-drive automatic washing machine
with pump
This manual is for
XQS60-78
User's manual
Please read this manual
carefully before using.
Retain it for future reference.
0030806076B
Contents
Names of the parts
Safety precautions
Installation and adjustment
Usage of the drain hose
Installation the water inlet hose
Preparation before washing
Put in the laundries
Usage of the detergent
Use the operation buttons
Close the top lid
Finish washing
Disposal after washing
Trouble shooting
Packing list Specification
Answer to question
*
*
Names of the parts
Round cover
Attachment block
Pulsator
Water inlet valve
Water absorption
cushion
Cabinet handle
Power cord
Drain hose
Back cover
Adjustable foot
seam
Meaning and description of the symbols
Contents marked with that symbol are related
Warning sign
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Top lid component
Inner cover component
Detergent box
Liquid whitener inlet
Control panel
Outer tub cover
Balance ring
Lint filter
Inner tub
Front control board
Cabinet
Cabinet base
Adjustable leg
Fixed leg (3 pieces)
Forbidding sign
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
Safety precautions
Please insert the power cord into
special receptacle with rated voltage. Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably .If possible, please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be inserted and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
In case the washing machine is installed on ground with carpet, do not
block the ventilation hole with carpet.
Do not use water hotter than 50 C .
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
The ventilation holes
at the bottom
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
The handicapped or children without
care shall not use the machine.
Do not decompose, repair or alter the
machine by yourself.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
l
r
e
Petro
inn
h
T
Keep the machine away from direct
sunlight and heat source like the heater.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged,please contact the local
after-sales service department of our company.
The front cover of lint filter
dismantle
The back cover of lint filter
install
To protect your laundries and washing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
It is suggested to use foamless washing
powder.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual
It is very important to your security and correct operating the machine.
Install the inner cover component
Before using the washing machine firstly, please install the inner cover component.
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming the inner cover
shaft to the installation hole of the corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of the left side into the corresponding outer tub
cover shaft groove(see to the figure 1), then hold the middle position of the front of
the outer tub cover with left hand forcibly , handhold the right and below position of
the inner cover with right hand, push the inner cover to the outer cover vertically,
make the inner cover shaft into the corresponding outer tub cover shaft groove(see
to the figure 2). Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner cover, and the
operation shall be smooth. Do not dismount the inner cover component after washing.
Outer tub cover
Outer tub cover shaft groove
Inner cover shaft
Left hand
Right hand
Inner cover component
Figure 1
Install the bottom plate
After opening the package, please lean the washing
machine gently down on soft items (like towel cloth,
blanket, etc.). Install the bottom plate to the bottom of
the machine with eight screwsby a cross screwdriver,
then lift the machine up gently. See to the figure:
Bottom plate
Figure 2
Screw
Front
Back
Soft object
Adjust the Installation position
The washing machine away from wall should be overrun 20mm. The largest allowable slope of the
shank base of the machine is 1 .The slanting or rough ground will result in unstable running or
stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 . After adjustment, fasten the nut.
Loosen
High
Low
Fasten
the adjustable nut
the adjustable feet
Usage of the drain hose
The drainage shall be smooth with the drain hose
ut the drain hose up to suitable position. Do not
put it on ground.
Notes: the mouth of drain pipe should higher than
the water level of washing tub for avoiding
to siphon phenomenon during drain.
0.7<H
Mouth of
drain hose
<1.2m
Do not tramp or press the drain hose.
Installation the water inlet hose
Confirm the water faucet
water faucet, suitable water faucet, not suitable
The exit end face of the faucet
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
water inlet hose jointer
Slider
Screw
Lock lever
water inlet hose
Screw knife
Figure 1
Sign plate
Figure 2 Figure 3
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..
Screw nut
Figure 4
Figure 5
Figure 6
Bushing
About 4mm before twisting
About less than 2mm after twisting
Connection between the water inlet hose and the washer
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
nut of the water
inlet hose
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
jointer of the
water inlet valve
water absorption
cushion.
Connection between the jointer of the water inlet hose
and the water inlet hose
1.Push down the slider. Insert the water inlet hose into the jointer.
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Locking lever
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
the jointer of the
water inlet hose
Slider
Dismantle the water inlet hose
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
If the machine is used frequently, the jointer of the water inlet hose can be
on the faucet to prevent damaging the fixing screw.
kept
Locking lever
Slider
7
1 Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put the drain hose up to suitable position.
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Check if
the laundries
has special
requirement
on washing
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
Clear the
pocket. Take
out the coins,
sand, hairpins
etc.
Tie the long
strips; fasten
the buttons;
close zippers.
The quantity of
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.
When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion, please
put the laundries
with buttons into
other laundries.
2 Put in the laundries
3
Usage of the detergent
Inlet for concentrated washing
powder and detergent
Access for detergent
The capacity of washing and spinning of he machine
refer to the largest weight of the standard laundries under
dry condition that can be washed or spinned in one time.
One time washing quantity shall be lower than the rated
capacity.
The thickness, size, type of the cloth will influence the
actual washing capacity. It is suitable for one time
washing to put in reasonable amount of laundries and
the laundries can be turned round in washing.
Do not select above " 4 " water level for laundries
less than 1.0kg ,so as to avoid splashing of water.
Put the washing powder and softener into the detergent
box directly as indicated in the left figure.
After that, please close the detergent box. Refer to the
following table for the usage of the detergent: The
standard dosage of the detergent and the water
quantity
Access for softener
How to use the washing powder
Detergent box
How to use the softener
When you use softener, the softener must be lower
than the underside of water cap.
Please often wash the detergent box, because
softener may curdle easily.
Before use softener ,you must select disinfect
program first.
How to use the whitener
Fill water to decided level .Dilute the whitener with
container. Pour it slowly into the washing tub.
Avoid using whitener on laundries with colour or
pattern as they are prone to lose colour.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before use.
Directly dissolved in the machine (not applicable for fuzzy
program and reserve wash)
1.Fill small quantity of water.
2.Add the powder. Run for 30 seconds to dissolve it completely.
3.Put in the laundry. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 and a container.
2.Add the powder while stirring to fully dissolve it. In selecting
The super quick program, it is suggested to adopt liquid
detergent instead of washing powder to guarantee the
washing effect.
Put in the proper quantities detergent according to the water
level and the laundries quantities.
It is suggested not to use high sudsing detergent.
Washing powder with poor quality or long time storage
maybe caked. Please pay attention to cleaning the
detergent box in time.
4 Use the operation buttons
Description of the function of buttons
Mode and meaning of the indicators
Flashing: indicate the running program
On: indicate the program about to run, or indicate the selected mode
SOAK
Digital tube
During sensing, it displays
During operation of programs, it displays theremained time (minute) or remained times of the
corresponding procedure
MINUTES
MINUTE
S
WASH
RINSE
DISINFECT
TIMES
MINUTES
DISINFECT
SPIN
Soak button
Push the soak button to set
the soak procedure.
Push the soak button to set
the soak procedure. During
normal ,jean ,common programs, push the soak button to set different soak time
(10, 20, 30, 40 minutes).
During cotton programs,
push the soak button to
select soak procedure,
but the soak time cannot
change.
During quick , posthaste,
woollen and silk programs,
push the soak button, the
machine have no reaction.
Wash button
Push the wash button to
set the wash procedure.
During normal,jean,common
programs, push the wash
button to set different wash
time (from 0 to 25minutes)
During cotton ,woollen and
silk programs, push the
wash button to select wash
procedure, but the wash
time cannot change.
During quick, posthaste,
programs, push the wash
button the machine have
no reaction.
Rinse/Disinfect button
Push the rinse/disinfect button to set the rinse
procedure and disinfect function.
During common jean and normal programs, push the
rinse/disinfect button to set different rinse times ( 0,
1, 2, 3, 4 times)
During cotton , woollen and silk programs, push the
rinse/disinfect button to select rinse procedure, but the
rinse times cannot change.
During quick , posthaste programs, push the rinse/
disinfect button less than 2S , the spin procedure have
no reaction.
During common program, the machine is set to save
water program. If you push the rinse/disinfect button
before starting operation, it will change to water storage
rinse program.
Push the rinse/disinfect button 2S ,you may select or
cancel the disinfect function ,when the disinfect indicator
is indicating ,it means the disinfect procedure is sele cted.
The disinfect water is turn into the inner tub at the last
times.
Spin button
Push the spin button to set
the spin procedure.
During normal, jean,common
programs, push the spin
button to set different spin time
(from 0 to 9 minutes)
During cotton , woollen and
silk programs, push the spin
button to select spin procedure,
but the spin time cannot
change.
During quick ,posthaste
,programs, push the spin
button, the machine have no
reaction.
Child lock function
Push and hold the water level button and spin button, then push down the power on/off
button. The digitron displays CL . You can continue setting desired washing procedures.
After setting, push down the start/pause button. The child lock function is activated. All of
the buttons are locked and cannot make selection.
Release the child lock function: push down the water level and spin button at the same
time for more than 1 second. After a beep sound, the child lock function is released.
Reserve/remain time indicator digitron
During sensing, it displays -During reserve procedure, it displays the remained reserve time (in
hours)
During operation of programs, it displays the remained time (minutes).
If the remained time exceeds99 minutes, it adopts A at tens place to
represent 100 minutes, b to represent 110 minutes. For instance, A3
represents103 minutes.
In case of abnormal phenomenon, it displays
the abnormal symbol (see to Page 16)
Power On/Off button
Push the On/Off button to switch
on the power.
When the power is on, push it
again to switch off the power.
Push the On/Off button to switch
on the power.
If the start/pause button is not
pushed, the washing machine will
automatically switch off the power
after 5 minutes.
TIME REMAINED
(MINUTES)
RESERVE
(HOURS LATER)
RESERVE
+
Res
erve button
In normal operation mode,
the reserve indicator
light is off. The time
remain indicator light is
on. The digitron displays
the time remained (in
minute) before the
washing is finished.
Push down the reserve
button. The reserve
indicator light is on the
digitron displays the
reserve time of finishing
washing (in hour).
When the machine is
started, the reserve
indicator light is on,
indicating that the reserve
function is running.
9
7
5
3
1
WATER LEVEL
COMMON
10
8
6
4
NORMAL
COTT
WOOLL
SILK
SAVE
ON
POSTHASTE
EN
CARPETING
2
PROGRAM
W
ater level button
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value
among 4, 6, 8,and 10 automatically.
You can also set water level by yourself. After the machine is
started, it will not set water level automatically. You shall push
the start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .
If wet laundries are put in, it may display water level 10 . You
must set suitable water level by yourself.
If posthaste program is selected, it will display water level 3 .
When water level 2 is reached in water filling, it will perform
washing while filling water. When water level 3 is reached, it
will change to normal washing.
During operation of wash and rinse program, you can push
down the water level button to add water. When you release
the button, or it reaches the overflow water level, the machine
will stop adding water.
The water level decided may be different from actual value
because of the different moisture level of the laundries.
POWER
ON/OFF
START
PAUSE
Start/Pause b
utton
After the power is switched on, push it to Start the machine
During working, push it to pause working.
During pause, push it to resume working.
Program se
lection button
Following automatic programs are available for selection
Program
Common
Save
Posthaste
Carpeting
Normal
Cotton
Woollen
Silk
Applicable situation
Common washing
Posthaste wash of the laundry under 1 kg
with light soil
Super quick wash of the laundry under 1
kg with light soil
Washing the relatively big and thick laundries
Washing the normal laundries
Washing the cotton textiles
Washing the woollen textiles
Washing the textile
b Steps of using the operation buttons and description of each step.
MINUTES
SOAK
WASH
MINUTES
SE
RIN
DISINFECT
TIMES
0
TIME REMAINED
MINUTES
(MINUTE
DI
SINF
ECT
RESERVE
(HOURS LATER)
N
SPI
RESERVE
+
1
9
S)
8
7
6
5
4
3
2
1
WATER L EVEL
NORMAL
COTTON
WOOLLEN
ON
COMM
SAVE
POSTHASTE
CARPETING
SILK
M
RA
PROG
Push the "POWER ON/OFF " button to switch on the power.
After switch on the power ,the machine will set have
no disinfect function .
If select the disinfect function.Push the rinse/disinfect button .when the
disinfect is indicating .please refer 2 to operating or refer 3
to operating.
Push the "PROGRAM" button to select
2
After switching on the power, the machine will set normal program automatically. To select other automatic
program, push the "program" button till the relative indicator is on. Refer to the "program button" on Page
11 for the selection.
For instance: select "posthaste"program for laundries with small
quantity and light soil.
suitable automatic program.
Page 11
POWER
ON/OFF
PROGRAM
START
PAUSE
POWER
ON/OFF
In selecting the normal program, the machine
will execute fuzzy program to select water level
and wash time according to the cloth and weight
of the laundries. The full procedure is controlled
automatically.
Push the "SOAK", "WASH", " ", "SPIN" button to select suitable procedure.
RINSE
DISINFECT
SOAK
MINUTES
WASH
MINUTES
RINSE
DISINFECT
TIMES
D
IS
INF
EC
MINUTES
T
SPIN
After switching on the power, the washing machine will set to common
program including"wash, rinse,spin "automatically. To select other
procedures, push the "soak", " wash", " rinse" or "spin" button
to select the time of soak, wash and spin, and the times of rinse.
After switching on the power, if you push one of the button among
"wash", "rinse"and"spin", the digitron of the former procedures will
turn off automatically. The former procedures will not run. For instance:
after switching on the power. If you push the "spin" button first, it will
execute spin singly after starting.
.
Attention
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The pulsator will not rotate unless the water is
filled to selected water level(except Normal program).
The soak procedure can work in cooperation with automatic programs like standard, jeans, chemical
fiber and cotton. There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing,
and can not make setting in other cases.
When you select disinfect program you can use softener. If you don t select disinfect program
the washing machine has no function to use softener please don t put softener into detergent
box.
Press " WATER LEVEL "button,
select suitable water level
After switching on the power, the washing machine will execute fuzzy program automatically to detect
the cloth. After defection, it can set the water level automatically. To select other water level, first push
the "start/pause" button, then push the "water level" button to set the water level. Refer to "water
level button"in Page 11 for selection.
WATER
LEVEL
Page 11
Push the "reserve" button to select suitable
reserve wash program
After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing
procedure to be finished at reserved time, please push the " reserve " button to set the reserve wash program.
Refer to reserve button in Page 11 for selection
Confirm the operation of reserve program
When the "reserve" function is activated, the indicator light of the program you have set
will be off. The "reserve (hour)" and "time remain" indicator lights will be on. During
reserve procedure, push the "reserve" button to display the reserve mode.
To change the running program or cancel the reserve setting, you
need to switch off the power and make new selection.
Page
the washing will be finished after 18 hours.
RESERVE
Push the "start/Pause" button
START
PAUSE
5 Close the top lid
Except water filling and draining , if the top cover is opened,
the washing machine will stop running and alarm.
6 Finish washing
The washing machine cuts off the power supply
automatically when wash cycle ends.
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence
your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle:Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
Dismantle Install
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Please clean it with brush every two months.
The lint filter must be used during washing.
It must be cleaned in time after each using.
The methods of dismantle and install lint filter as
follows:
1.Push down the spring piece of the top lint filter
to make the claws out of the filter cover, and then
pull out the lint filter to get it down.
2.Pull the back of the lint filter, and then you can
get down it off the front cover of the lint filter.
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it tight
6.Make sure the lint filter is well installed, or it can
influence your use.
Dismantle and install lint filter
Filter cover
Lint filter
dismantle
Dismantle and install lint filter back cover
The front cover of lint filter
The back cover of lint filter
install
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
nner
Petrol
Thi
Alcohol
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.
Trouble-shooting Answer to question
Common phenomena
Phenomena Explanation
* The spinning is intermittent when it starts. * Balance the laundries to avoid slanting.
* The wash procedure pau ses. * The cloth sensor is detecting the cloth. It will start
adding water after about 48 seconds.
* Select SPIN program, but it doesn’t
work.
* The program is setting the drain time. A certain
period is needed before it starts spi nning.
* The pulsator pauses during washing, rinsing
or adding water.
* It is to avoid splashing during water filling.
* There may be some water flowing out of the
drain hose in the first use of the machine.
* It is the water remained in the performance
inspection by the factory.
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomenan The reason How to settle
The digitron displays E0.
The drainage cannot work, or is too slow.
The digitron displays E1.
It stops running in midway. The digitron
displays E2.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
The water filling does not work, or is
slow. After about 15 minutes later,
the digital displays E4.
The digitron displays E6.
The digitron displays E8.
The digitron displays E9.
Not wash
The machine does
not act
Not spin
There's abnormal sound
inside the machine
The water tap leaks
The top lid is opened during reserve
procedure.
Does the drain hose hang up at the
suitable position?
Is the drain hose blocked?
The top lid is not closed.
Are the laundries put slantingly?
Is the machine slanting?
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water level sensor is bad.
The power voltage is too low.
The power voltage is too high.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Is the screw of the jointer of water
inlet hose loose or awry?
Close the top lid.
Hang up the drain hose at the suitable position,
refer to page 5. Open and close the top lid once.
Clean the foreign material. Open and close
The top Lid Once.
Close the top lid.
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.
Please contact the after-sales
service department.
Pull off the power plug. Wait for the
voltage resuming normal before usage.
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the screw of the jointer properly.
Packing list
Name
User's manual
Warranty card
The end connecting to
the washing machine
Jointer connecting
the water inlet hose
to the water faucet
The end connecting to
the water inlet hose jointer
Inner cover component
Bottom plate
Tapping screws
Quantity
One piece
One piece
One piece
One piece
One piece
Eight pieces
Double-drive automatic washing machine
Specification
Water level/Water quantity (about)
Injection pressure(MPa)
Rated washing / spinning capacity(kg)
1/18L 2/24L 3/29L 4/34L 5/38L
6/42L 7/46L 8/50L 9/54L 10/59L
0.03~0.78
6.0/6.0 (weight of standard dry cloth)
One set
Loading...