XQS50-28
Names of the parts.............the 2nd cover
Safety precautions .............................................1
Installation and adjustment .........................3
Install the water inlet hose............5
Preparation before washing ...............7
Put in the laundries .............................8
Put in the detergent ............................9
Use the operation buttons ...................10
Close the top lid .................................14
Finish washing ...................................14
Disposal after washing .........................15
Trouble shooting..............................16
Packing list.....................................17
Specification................the back cover
CONTENTS
Before using
Using process
Please read this manual carefully bifore using.
Retain it for future reference.
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
The manufacturer will not take responsibility for those
risks occurred from not obeying this manual.
User's manual
Computerized automatic
Washing Machine
Specification
Model XQS50-28 Computerized automatic washing machine
Rated voltage frequency 220V ~ 50Hz
Rated washing / spinning capacity 5.0kg (weight of standard dry cloth)
Water level/Water quantity (about)
Max water consumption
Injection pressure 0.03Mpa~0.78Mpa
Rated washing power 380W
Rated spinning power 260W
Weight About 36kg
Dimension L 520 mm W 520 mm H 908 mm
About 100L(High water level; Standard program)
1/16L 2/20L 3/24L 4/28L 5/32L
6/38L 7/42L 8/45L 9/47L 10/50L
Packing list
Name
User's manual
Quantity
One
Two
Storage position
Inside the document bag
Inside the accessory bag
Between the upper cushion of the
washing machine package and the
upper seal of the package carton
Inner cover component
Components of the
water inlet hose
Inside the accessory bag
Eight
Tapping screws ST4x16-A
Bottom plate
One
One
Computerized Automatic
washing machine
One
Inside the accessory bag
Lint filter
One
Inside the document bag
Before Using
Before Using
Names of the parts
Contents marked with that symbol are related to the safety of the product and the personal
safety of the users. Please operate in strict conformity to the contents.
Contents marked with that symbol are actions forbidden to perform. Performing of those
action may result in damage of the machine or influence the personal safety of the users.
Accessories
Meaning and description of the symbols
£¨one piece£©
Bottom plate (1 piece)
Water inlet hose (2 piece)
Water inlet hose joint (2piece)
Fastening screws
ST4X16 (8 pieces)
the end connecting to the washing machine
jointer connecting the water
inlet hose and the water faucet
the end connecting to the water
Inner plate (1 piece)
inlet hose jointer
Lint filter (1 piece)
Control pannel
Outer tub cover
Lint filter fixing
Balance ring
Inner tub
Filter cover
Attachment block
(3 pieces)
Cabinet
Liquid whitener inlet
Fixed leg
Adjustable leg
Detergent box
Top lid component
Inner cover component
(3 pieces)
Pulsater
Lint filter
Adjustable leg film
Water inlet valve
Water absorption
cushion
Rear faceplate
Power cord
Front congrol board
Cabinet handle
Outer drain hose
Back cover
Drain hose jacket
Drain hose frame
The ventilation
holes at thebottom
Before Using
Before Using
Safety precautions
In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not
put wet laundries on the control panel coating
.
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose, do not use
the plug any more.
Do not wash water-proof laundry like the raincoat,
bikecovers, down textiles etc. To avoid abnormal
vibrations in spinning and damages to the laundries.
Do not bend, stretch, twist, bind the power cord by force, or reformit.
Do not press or clamp it with heavy items. If the power cord and power
plug are bad, or the receptacle is loose, be sure to have it replaced by
the technicians of our special shop or our agent,or the after-sales service
department to avoid any risk.Keep the prong of the power plug clean.If
dust is found on the power plug, please wipe it off with dry cloth.
In normal usage of the washing machine, the power
plug shall be ready to be pulled or plugged with hang.
Be sure to pull the plug off and close the water faucet
when occurring power failure,delivering the maching,
setting the machine idle or cleaning the machine,Do
not plug or pull the power plug with wet hand.
earth
Do not use water with temperature higher than 50
Please plug the plug on special 220V AC receptacle.
Be sure to use three phase power receptacle.Ensure
the earthing prong of the power redeptacle is earthed reliably.Use leakage protector if possible.
The digitron displays E0.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
The water filling does not work, or is
slow. After about 15 minutes later,
the digital displays E4.
The drainage cannot work, or is too slow.
The digitron displays E1.
It stops running in midway. The digitron
displays E2.
The power voltage is too low.
The top lid is not closed.
The top lid is opened during reserve
procedure.
Close the top lid.
Close the top lid.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and close the
top lid once.
Clean the foreign material. Open and close
The top Lid Once.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pausebutton once.
Push the sStart/Pause button once.
The water level sensor is bad.
Please contact the after-sales
service department.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Is the screw of the jointer of water
inlet hose loose or awry?
Pull off the power plug. Wait for the
voltage resuming normal before usage.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the screw of the jointer properly.
The water tap leaks
The digitron displays E8.
The digitron displays E6.
There's abnormal sound
inside the machine
Phenomenan The reason How to settle
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
The digitron displays E9.
The power voltage is too high.
The machine does
not act
Not wash
Not spin
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Common phenomena
Phenomena Explanation
* The spinning is intermittent when it starts. * Balance the laundries to avoid slanting.
* The wash procedure pauses. * The cloth sensor is detecting the cloth. It will start
adding water after about 48 seconds.
* Select “ Spin” program, but it doesn’t work. * The program is setting the drain time. A certain
period is needed before it starts spinning.
* The pusaltorpauses during washing, rinsing
or adding water.
* It is to avoid splashing during water filling.
* There may be some water flowing out of the
drain hose in the first use of the machine.
* It is the water remained in the performance
inspectionby the factory.
Do not put hand into the rotating tub.It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not decompose, repair or alter the machine by
yourself.
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Do not wash laundry with volatile materials
(such as thinner, petrol etc.).
Keep the machine away from direct sunlight and
heat source like the heater.
The handicapped or children without care shall not
use the machine.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged,please contact the local
after-sales service department of our company.
Benzene
Before Using
Before Using
Safety precautions
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Please check if the water faucet is open, and if the
connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Please clean it with brush every two months.
Using process
Using process
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence
your using the machine.
The lint filter must be used during washing.
It must be cleaned in time after each using
Lint filter:
1.
Rotate the inner tub with hand till the lint filter reaches
the position convenient for you to take it off. Pull it up to
dismount.
2.Push it down to install.
3.Clean the filter screen after washing.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle:Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
Dismantle Install
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
T
hinn
er
Petrol
Alcohol
Please first pull off the power plug from the receptacle before cleaning.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.
4.Hang up the power cord and drain hose.
3.Be sure to pull off the power plug before maintenance.
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
Dismantle
Install
Dismantle
Install
Dismantle
Install
Dismantle
Install
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
Adjust the Installation position
Screw
Back
Front
bottom plate
Soft object
FastenLoosen
High
Low
the adjustable nut
the adjustable feet
Please install and adjust the machine according to the requirement of the mannual.
It is very important to your security and correct operating the machine.
Before Using
Before Using
Installation and adjustment
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 . After adjustment, fasten the nut.
After opening the package, please lean the washing machine
gently down on soft items (like towel cloth,blanket, etc.). Install
the bottom plate to the bottom of the machine with eight screws
by a cross screwdriver, then lift the machine up gently.
See to the figure:
Push the "Start/Pause" button
5 Close the lid
6 Finish washing
After Finishing wash
alarm automatically
After finishing wash it'll alarm automatically
As the top lid opened ,the Washer will automatically give an alarm
and stop running , then drain automatically after 15s ,exclusively
during supplying water and rinsing.
Using process
Using process
* Total time: including the normal water inlet time and drain time. The total washing time may be influenced by
the water inlet pressure and water level.
* Spin time: From the moment the intermittent spinning starts to the moment it stops running (the time displayed
on spin digitron is from intermittent spinning to the moment before inertia spinning; the time displayed on the
time remain digitron is the total remaining time)
* In selecting "super quick" program, the washing machine will set the complete procedures of water level
selectior, washing, rinsing and spinning automatically.
Push the "reserve" button to select suitable reserve wash program
Start
Pause
After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing
procedure to be finished at reserved time, please push the " reserve " button to set the reserve wash program.
Refer to reserve button in Page 11 for selection
When the "reserve" function is activated, the indicator light of the program you have set
will be off. The "reserve (hour)" and "time remain" indicator lights will be on. During
reserve procedure, push the "reserve" button to display the reserve mode.
To change the running program or cancel the reserve setting, you
need to switch off the power and make new selection.
The washing will be finished after 18 hours.
Confirm the operation of reserve program
Reserve
Time
( remain)
Reserve
(hour)
Page
Install the inner cover
Install the lint filter
Install the lint filter in the balance ring.
Install the bottom plate
Inner cover
Inner cover shaft
Outer tube cover
Section • enlarging
Push
Outer tube cover
shaft groove
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover,
aiming the inner cover shaft to the installation hole of the
corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the
corresponding outer tub cover shaft groove, then push
the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position
to guarantee there are no dropping or abnormal sound in
opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component
after washing.
Dismantle
Install
lint filter
Useage the drain hose
Before Using
Before Using
How to change the direction of the drain hose
1. Dismount the back cover of the washing machine.
2. Take off the drain hose frame. Put down the drain
hose. Take off the drain hose rack. As indicated
in Figure 1, put the drain hose into the cabinet.
Then put one hand into the cabinet to nip the claw
of the drain hose bushing to release the claw from
original position. Take off the drain hose bushing
with the other hand. (As indicated in Figure 2 and 3).
Attention: To guarantee the proper installation, it is suggested to have the direction changing of drain
hose performed by the after-sales service technicians of our company.
3. Dismount the protecting cover of the drain
outlet at the other side ( method the same as
the drain hose bushing). Install the drain hose
bushing as per indicatedin Figure 4.
4. Extend the drain hose from the other side.
Fix the drain hose onto the cabinet with the
drain hose rack. (As indicatedin Figure 5) Take
on the drain hose frame , hang up .
•••• • ••••• ••••
•••••• •
•••••• •
•••• ••••••• ••••
••••••
•
••••
•••••
•••• • • •
•••••• •
•••••
•••• •••••••
•••••• •
•••••• •
•••• • ••••••••••••
••••••
•
••••
••••
Press " WATER LEVEL "button,select suitable
water level
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level. Refer to "standard dosage of detergent and
water quantity"in Page 9 and "water level button"in Page 11 for selection.
WATER
LEVEL
Page 9
Using process
Using process
.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The pulsator will not rotate unless the water is
filled to selected water level.
Attention
Page 11
Water Level and Time Table for Each Program (self programming not included)
After switching on the power, the washing machine will set to common program including"wash, rinse,
spin "automatically. To select other procedures, push the "soak", " wash", " rinse" or "spin" button
to select the time of soak, wash and spin, and the times of rinse. After switching on the power, if you
push one of the button among "wash", "rinse"and"spin", the digitron of the former procedures will
turn off automatically. The former procedures will not run. For instance: after switching on the power. If
you push the "spin" button first, it will execute spin singly after starting.
The soak procedure can work in cooperation with automatic programs like standard, jeans, chemical fiber and
cotton.There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing, and can not
make setting in other cases.
Program Water
level
Wash
(min)
Rinse (min/time) Spin (min) Total time
(min)
Standard 1-10 About
10-16
Save water program, total 10 around About 19-25
Quick 1-10 About 5 Save water program, total 10 arou nd About 15
Super quick 3 About 2 Save water progra m, total 4 around About 6
Jeans 1-10 About 20 Rinse twice, about 5 each
time
About 6 About 54
Chemical fiber 1-10 About 12 Rinse twice, about 3 About 4 About 41
Cotton 1-10 About 10 Rinse twice, about 3 About 4 About 49
Wool 1-10 About 3 Rinse twice, about 2 About 3 About 24
Silk 1-10 About 5 Rinse twice, about 2 About 3 About 30
Before using , hang up the drain hose on suitable location.
Do not put down the drain hose on the ground.
<1.2m
Confirm the end of drain hose is higher than the level
of tub . If not the siphon will being .
••••• •••• ••••••
••••• ••••
••••••••••••••••
••••• •••• ••••••••
••••• •••• •••••
5. Install the drain hose protecting cover on
the other side.(As indicatedin Figure 6) .
The exit end face of the faucet
Confirm the water faucet
Connection between the water inlet hose jointer and the water faucet
water faucet, suitable water faucet, not suitable
It is required that the front end shall be longer than 10cm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
3.Fasten the four screws evenly. See to Figure 4.
About 4mm before twisting
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..
About less than 2mm after twisting
water inlet hose jointer
Screw knife
Screw
Bushing
Sign plate
Screw nut
water inlet hose
Figure 1
Figure 4
Figure 2
Figure 5
Figure 3
Figure 6
Slider
Lock level
Before Using
Before Using
Install the water inlet hose
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
After switching on the power, the machine will set standard program automatically. To select other automatic
program, push the "program" button till the relative indicator is on. Refer to the "program button" on Page
11 for the selection.
For instance: select "super quick" program for laundries with small
quantity and light soil.
Page 11
Push the "Power on/off " button to switch on the power.
POWER
ON/OFF
Steps of using the operation buttons and description
of the steps
Using process
Using process
2
Push the "program" button to select suitable automatic program.
program
In selecting the standard program, the machine
will execute fuzzy program to select water
and wash time according to the cloth and weight
of the laundries. The full procedure is controlled
automatically.
Chemical fiber
Standard
Cotton
Quick
Wool
Super quick
Silk
Jeans
10
8
6
4
2
9
7
5
3
1
FIBRE
COTTON
WOOLLEN
SILK
POWER
ON/OFF
START
PAUSE
PROGRAM
RESERVE
WATER LEVEL
Time reman
(Minutes)
Reserve
(Hour)
M
inutes
Times
NORMAL
QUICK
POSTHASTE
Soak wa
sh
ÍÑË®
ÍÑË®
XQS50-28
WASH
RISE
SPI
N
Cold/Cold
Warm/Cold
Hot/Cold
M
inutes
Wash
Rinse
Spin
Push the "wash", "rinse" , "spin"or"TEMP wash/rinse" button to select suitable procedure.
Minute
Times
Minute
Cold/Cold
Warm/Cold
Hot/Cold
Connection between the water inlet hose and the washer
Dismantle the water inlet hose
Connection between the jointer of the water inlet hose
and the water inlet hose
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
1.Push down the slider. Insert the water inlet hose into the jointer.
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Locking level
Slider
water absorption
cushion.
nut of the water
inlet hose
the jointer of the
water inlet hose
Slider
Locking level
jointer of the
water inlet valve
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
If the machine is used frequently, the jointer of the water inlet hose can be
kept
on the faucet to prevent damaging the fixing screw.
Before Using
Before Using
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
The washing machine can detect the laundries automatically. After detection,it will
set the water level to suitable value among 4, 6, 8,and 10 automatically.
You canalso set water level by self. After the machine is started, it will not set water
level automatically. You shall push the start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the laundries and will
display water level 6 .
If wet laundries are put in, it may display water level 10 . You must set suitable
water level by self.
If super quick program is selected, it will display water level 3 . When water level
2 is reached in water filling, it will perform washing while filling water.
When water level 3 is reached, it will change to normal washing.
During operation of wash and rinse program, you can push down the water level
button to add water. When you release the button, or it reaches the overflow water
level, the machine will stop adding water.
The water level decided may be different from actual value because of the different
moisture level of the laundries.
Start/Pause button
Push the On/Off button to switch on the power.
When the power is on, push it again to switch off
the power.
Push the On/Off button to switch on the power.
If the start/pause button is not pushed, the
washing machine will automatically switch off
the power after 5 minutes.
10
8
6
4
2
9
7
5
3
1
»¯ÏË
ÃÞÖ¯·
ë֯·
Ë¿
Ö¯·
μçÔ´
ô¯
ÔÝÍ£
³ÌÐò
Ô¤Ô¼
ˮλ
Ê£Óà
(· ÖÖÓ)
Ê£Óà
(· Ö
ÖÓ)
Ô¤Ô¼
(Ð ¡Ê±)
Ô¤Ô¼
(Ð ¡Ê±)
±ê¼
¿ìËÙ
ÌØ¿ì
£Ð
ͯËø
During operation of programs, it displays the remained time
(minute). If the remained time exceeds99 minutes,it adopts A at
tens place to represent 100 minutes, B to represent 110 minutes.
For instance, A3 represents 103 minutes.
In case of abnormal phenomenon, it displays the abnormal
symbol (see to Page 16)
Page16
Reserve/remai
n time indicator d
igitron
START
PAUS E
POWER
ON/OFF
RESERVE
WATER LEVEL
PROGRAM
FIBRE
CO
TTON
WOO
LLEN
SI
LK
NORMAL
QUICK
POSTHASTE
SOAK WASH
ReserveReserve
In normal operation mode, the reserve indicator light is off. The time remain indicator light is on.
The digitron displays the time remained (in minute) before the washing is finished.
Push down the reserve button. The reserve indicator light is on The digitron displays the reserve time of
finishing washing (in hour). When the machine is started, the reserve indicator light is on, indicatingthat
the reserve function is running.
After the power is switched on, push it to
Start the machine
During working, push it to pause working.
During pause, push it to resume working.
Reserve button
Water level button
Program selection button
Following automatic programs are available
for selection
Program
Applicable situation
Standard
Common washing
Quick
Quick and high-efficiency wash for
common laundries
Super
quick
Super quick wash of the laundry
under 1 kg with light soil
Jeans
Washing the relatively big and
thick laundriesr
Chemical
fiber
Washing the chimical fiber
laundries
Cotton
Washing the cotton textiles
Power On/Off button
Washing the textile
Washing the woolen textiles
Silk
Wool
R
eserve
Hou
rs later
T
ime remained
Minutes
XQS50-28
Description of the function of buttons
Mode and meaning of the indicators
Digital tube
Flashing: indicate the running program
On: indicate the program about to run, or
indicate the selected mode
During sensing, it displays
During operation of programs, it displays the
remained times (minutes) or remained times of
the corresponding procedure
·Ö
·Ö
´Î
½þ Ý
Ï´μÓ
¯Ï´
ÍÑË®
Cold/Cold
RINSE
SPIN
Push the wash button to set the wash procedure.
During standard and jeans programs, push the wash
button to set different wash time (from 0 to 25 minutes)
During chemical fiber , cotton wool and silk programs,
push the wash button to select wash procedure, but the
wash time cannot change.
During quick,super quick,programs,push the wash button
the machine have no reaction.
Push the rinse button to set the rinse procedure.
During standard and jeans programs, push the soak
button to set different rinse times ( 0, 1, 2, 3, 4 times)
During chemical fiber , cotton wool and silk programs,
push the soak button to select rinse procedure, but the
rinse times cannot change.
During quick , super quick , programs, push the soak
button, the machine have no reaction.
During standard program, the machine is set to save water
program. If you push the rinse button before starting
operation, it will change to water storage rinse program.
Push the spin button to set the spin procedure.
During standard and jeans programs, push the spin
button to set different spin time (from 0 to 9 minutes)
During chemical fiber , cotton wool and silk programs,
push the spin button to select spin procedure, but the spin
time cannot change.
During quick ,super quick ,programs, push the spin button,
the machine have no reaction.
Minutes
Times
Minutes
Wash button
Rinse button
Spin button
·Ö
´Î
Ï´μÓ
WASH
Warm/Cold
Hot/Cold
TEMP Wash/Rinse button
When you turn the power on ,the initial temperature is
set at Cold/Cold position.
Press the TEMP Wash/Rinse button to selectthe proper
temperature option.For your convenience,there are three
temperature option:Cold/Cold,Warm/Cold,Hot/Cold.
ͯËø
Using process
Using process
1 Preparation before washing
Confirm if there's
special requirement
for the laundries.
Clear the pocket.
Take out the coins ,
sand,hairpins etc.
Fasten the buttons
and zippers.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
laundries.
Preparation before washing
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
Pay attention to followings before washing the laundries
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Hang up the drain hose.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
For those small laundries and those may get twisting or worn, and woollen/fur laundries, please put them into
mesh bag for washing.
<1.2m
Reference weight of the laundries:
working suit up,down
jeans about 800g
The capacity of washing of the machine refer to the
largest weight of the standard laundries under dry
condition that can be washed in one time. Laundries
quantity in one washing cycle shall be lower
than the rated capacity. The largest capacity of
this machine is 5.0kg.
The thickness ,size , type of the cloth will influence the
actual washing capacity. It is suitable to put in
reasonable amount of laundries and the laundries can
be turned round in washing for one time washing.
Do not select " 4" water level for laundries less
than 1.0kg ,so as to avoid splashing of water.
shirt
jacket
single bed sheet
socking
underpants
undershirt
pajamas
blanket
cotton,about 900g
cotton,about
300g
cotton,about
800g
cotton,about 600g
blending,about 50g
cotton,about 70g
cotton,about 180g
about 200g
Using process
Using process
2 Put in the laundries
cotton,about 1120g
coat with blended
cloth (about 800g)
How to use the whitener
Standard usage of the detergent and water quantity
Laundries
quantity
(kg)
Water
level
Water
quantity
Common powder,
Put the washing powder and softener into the detergent box
directly as Indicated in the left figure.
After that, please close the detergent box.Refer to the following
list for the usage of the detergent :he standard dosage of the
detergent and the water quantity.
How to use the washing powder
Fill water to decided level .Dilute the whitener with
container. Pour it slowly into the washing tub.
Concentrated powder,
Add 40g in each 30L water
Add 25g in each 30L water
3 Put in the detergent
Using process
Using process
Avoid using whitener on laundries with colour or
pattern as they are prone to lose colour.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before use.
Below 0.5
About 50L
About 45L About 60g About 37g
About 38L About 51g About 32g
About 28L About 37g About 23g
About 20L About 27g About 17g
About 47L
About 42L About 56g About 35g
About 32L About 43g About 27g
About 24L About 32g About 20g
About 16L About 21g About 13g
About 67g About 42g
About 63g About 39g
Access for detergent
Access for softerner
Directly dissolved in the machine (not applicable for fuzzy
program and reserve wash)
1.Fill small quantity of water.
2.Add the power.Run for 30 seconds to dissolve it completely.
3.Put in the laundry. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 and a container.
2.Add the powder while stirring to fully dissolve it.In selecting
The super quick program, it is suggestedto adopt liquid
detergent instead of washing powder to guarantee the
washing effect.
The powder is more prone to pollute the laundry than the
detergent. Therefore please use it with suitable quantity.
It is suggested not to use high sudsing detergent.
Washing powder with poor quality or long time storage
maybe caked. Please pay attention to cleaning the
detergent box in time.
Loading...