Haier XQG60-HA800TXM, XQG60-HA1000TXM User Manual
AUTOMATIC DRUM
WASHING MACHINE
XQG60-HA800TX(M)
XQG60-HA1000TX(M)
INSTRUCTIONS FOR
INSTALLATION AND
OPERATION
FUNCTION INTRODUCTION.....................................................3-4
INSTALLATION...........................................................................5-7
CLOSE UP.................................................................................8-10
USING INSTRUCTIONS..........................................................11-15
MAINTENANCE...........................................................................16
SOLUTION TO PROBLEMS.................................................17-18
ATTACHED CHART:
GUIDE FOR SELECTION PROGROMME...................................19
WARNING.....................................................................................20
1
FUNCTION INTRODUCTION
FUNCTION COMPARING TABLE
FUNCTION
MODE
Washing capacity
Programmes
Cotton
Synthetic
Wool
Adjustable thermostat(0~90 C)
Cold wash button
Speed button
Economic button
Spin speed
Power switch
ON/OFF
Rinse
XQG60-HA1000TX(M)
6kg
18
●
●
●
●
●
●
1000r/min
●
●
XQG60-HA800TX(M)
6kg
18
●
●
●
●
●
●
850r/min
●
●
Stainless steel tub
Door-locking device
Power
Power(Wash)
Power(Spin)
Weight
HX.WX.D
300W
530W
72Kg
850X550X595
2
●
●
●
●
●
●
300W
530W
72Kg
Installation
Unpacking
levelling and
positioning
Remove the package and check that the machine is
undamaged.
If you have any doubts, do not use the machine and call on a
qualified technician. Keep all packing parts (plastic bag,
foam rubber, screws etc.) out of the reach of children since
they could be dangerous.
Important: The inside of the washing machine which
consists of a floating unit, is fixed with screws at the back of
the cabinet (Fig.1) during transport. Before starting the
machine remember to release the floating unit by removing
the above screws . To prevent water spray from entering the
machine, remember to close the holes left open by the
screws with the plastic caps provided in the packet
containing the owner's manual. And rescrew the holes
where the iron piece is taken down with the former two
screws.Attention:keep the packing screws and plastic caps
in a safe place for later use. It is important for the machine to
be perfectly level (the angle of inclination on the work surface
must not be more than 2 degrees). For this reason the
machine is fitted with adjustable feet used for levelling the
machine before use (Fig.2). In the case of flooring with
carpeting, remember to check that the ventilation in the
support area is not plugged.
Fig.1
Fig.2
3
Installation
Electric
connection
Connection
of tap and
Loading
Hose
Connect the plug to a socket provided with efficient earthing.
Or use the spare earthing wire supplied together with the
machine and the earthing terminal located on the left-upper
corner of the back of your machine (Warning: this appliance
must be earthed as a safety measure according to the law).
Make sure that the voltage and frequency available
correspond with the values stated on the data plate located at
the back of the machine (power range:187-242V) and that the
electric system is dimensioned to withstand the maximum
current shown on the data plate. If the socket the machine is
connected to does not correspond with the plug, replace the
plug with a suitable one and avoid using adaptors or shunts
since they could cause overheating and burn out.The spare
eathing wire is absolutely not allowed to be connected to
water pipe,heating pipe or other kinds of pipes.
Connect the inlet hose to a cold water tap with a 3/4 gas
threaded opening, and fit the filter and the rubber gasket
supplied with the washing machine. Check that it is tightly
screwed to the tap (Fig. 3).
Fig. 3
If the water piping is new or has not been used for a long time,
before making the connection, let the water run until it is clear
and free from impurities.
This step is necessary to ensure that the incoming water
does not clog and possibly damage the machine.
4
Installation
Connection of
the Drain Hose
Connect the drain hose to a drain duct (with internal
diameter of at least 4 cm.) or place it for drainage into
a sink or a tub, ensuring that there are no kinks or
bends. The free end must be at a height of between
80 and 100 cm. Should it be necessary to fix the end
of the hose at a height of less than 80 cm from the
floor, the hose must be fixed in the appropriate hook
on the upper part of the back panel (Fig.4) or use the
supplied support to fix the drain hose.(Fig.5)
Fig.4
Connecting
WaterSupply
Fig.5
Insert stainless steel screen washers into end of each
supply hose and attach that end of supply hose to
your 3/4" water tap spigot.Be sure that you match up
cold water to "C" and hot to "H".Note:Home Centers
also have"Y" connectors and "Couplings" which
enable you to connect the machine to your sinks
faucet.
5
Close up
1 prewash
2 intense
3 normal
Cotton
4 delicate
5 rinse
6 softening
1 prewash
2 intense
3 normal
Cotton
4 delicate
5 rinse
6 softening
Synthetic
Synthetic
A intense
B normal
C delicate
D rinse
E softening
soak
F spin 7 spin
A intense
B normal
C delicate
D rinse
E softening
soak
F spin 7 spin
G
D
C
Ｉ
delicate
rinse
ＩＩ
ＩＩＩ
softening
Wool
soak
spin
ＩＶ
Ｖ
Draining
G
D
C
Ｉ
delicate
rinse
ＩＩ
ＩＩＩ
softening
Wool
soak
spin
ＩＶ
Ｖ
Draining
F1
E
H
MAXMAX
ＯＮＯＮ
ＯＦＦＯＦＦ
E
ＯＮＯＮ
ＯＦＦＯＦＦ
8080
５００５００
８５０８５０
F2
６００６００
１０００１０００
7070
H
MAXMAX
8080
7070
A
B
ＸＱＧ６０－ＨＡ８００ＴＸ（Ｍ）
Ｖ
１１
２２
ＩＶ
ＩＩＩ
ＩＩ
Ｉ
3030
ＦＦ
ＥＥ
4040
5050
6060
B
5050
6060
ＤＤ
A
ＩＩ
Ｉ
3030
ＦＦ
ＥＥ
4040
ＣＣ
７７
ＢＢ
ＡＡ
ＸＱＧ６０－ＨＡ１０００ＴＸ（Ｍ）
Ｖ
１１
２２
ＩＶ
ＩＩＩ
ＤＤ
ＣＣ
７７
ＢＢ
ＡＡ
３３
４４
５５
６６
３３
４４
５５
６６
6
Loading...