Haier XQG50-HN800TX Parts Manual

Haier WASHING MACHINE

Technical Document

Contents

Name of the parts----------- ------------------------------2

Trouble shooting----------------------------------------------3

Unpack and installation----- -----------------------------8 Cleaning and maintenance- ----------------------------10

Structural diagram----------------------------------------11

Wiring circuit-----------------------------------------------15

XQG50-HN800TX characters

Capacity: 5kg

VOLT: 220V~240V/50Hz POWER(WASH): 300 W POWER(SPIN): 40 0W POWER(MAX): 230 0W

Name of the parts

Temperature knob

Button

Top cover

Detergent box

Progam knob

Window

Door

Troubleshooting

-----------------------------------------------------------------------------------------

Troubleshooting

I .The appliance does not work. Possible causes

1.The socket is not the required one or the connection is loose.

2.The door is not properly closed or the switch of micro delay is in poor contact.

3.The plug wire of motor is in poor contact or the motor is broken.

4.Malfunction of electronic module

Troubleshooting

1.Check the socket and plug to make sure that they are properly connected.

2.Check whether the micro delay switch is in good contact in on-position. If yes, insert the terminal firmly to provide a good connection.

3.The electronic module controls the rotary speed and direction of the motor. In case of the failure, check the wiring or replace the electronic module.

II .Filling failure Possible causes

1.The switch of water supply is not opened or the water pressure is too low.

2.The door is not properly closed or the micro delay switch is in poor contact

3.The water electromagnetic valve is broken.

4.The plug wire of drainage pump is in poor contact.

5.The pressure switch is broken.

Troubleshooting

1.Repeat the following steps. Open the switch of water supply

1) Check whether the filling hose is twisted or blocked.

2) Check whether the water eletromagnetic valve is blocked.

3) Check whether program is properly selected.

4) Check whether the water supply pressure is too low.

2.Check the door catch and the door lock are in good contact. If not, make necessary adjustment. Check whether the micro delay switch is in good contact in on-position.

3.Check whether the electromagnetic is good in on-position. Fasten it if necessary. 4.Blow on the pressure switch and "click, click" can be heard. Otherwise, replace the pressure switch with

a new one.

III .No drainage

Possible causes

1.Improper installation

2.The drainage pump is broken.

Troubleshooting

1.Repeat the following steps.

1)Check whether the drainage pipe is twisted or blocked. The appropriate height of the water drainage outlet should be from 80 to100cm.

2)Check whether the program is properly selected.

3) Connect the power cable to the drainage pump to check whether the operation is normal. If not, make necessary replacement.

IV .Unusual noise Possible causes

1.The packing screws should be disassembled.

2.The washer is placed too near a wall. 3.The washer is

loaded over the standard capacity (5Kg).

4.There is foreign object other than fabrics in the washer.

5.The washer does not stand level.

6..Bolts or screws are loose.

7.The belt is loose.

8.Something is wrong with the triangle assembly.

Troubleshooting

1.Disassemble the packing screws.

2.Move the washer away from the wall.

3. Do not load the appliance more than the standard capacity.

4.Remove the foreign object.

5. Adjust the washer until it is level.

6.Tighten the bolts and screws.

1) .Fastening bolts of vibration damper

2) .Fastening bolts of balances

3) .Screws of water heating pipe

7.Increase the tension of belt.

8.Replace the triangle assembly.

V.The drum doesn't rotate; the spin speed is too high or too low.

Possible causes

1.The belt tension is too low or the fastening bolts are loose.

2.The plug wire of motor is loose or the motor is broken.

3.The capacitor is broken.

4.The electronic module is broken or is not properly plugged.

Troubleshooting

1.Adjust the tension of belt and tighten the screws.

2.Check whether the plug wire of motor is loose or whether the motor works normally. If not, make necessary replacement.

3.Check whether the capacitor is good with a universal meter. If not, make necessary replacement.

4.Replace the electronic module with a new one.

VI .The water level is too high.

Possible causes

1.Gas leakage at pressure system of water supply.

2.The pressure switch is broken.

Troubleshooting

1.Check whether the pipeline of pressure system is blocked or there is gas leakage. The pressure system includes: (1)Gas-collecting valve (2) Rubber pipe (3) Pipe clip

2.Blow on the pressure switch and "click, click" can be heard. Otherwise, replace the pressure switch with a new one.

VII .No heating or automatic heating Possible causes

1.Thermostat breakdown

2.Effect of ambient temperature

3.The water-heating pipe is broken.

Troubleshooting

1.Check whether the knob of temperature controller clicks at room temperature. If not, make necessary replacement.

Note:

1).The temperature controller breaks down when it is cold and no click can be heard. Warm the room and the temperature controller will get normal.

2).The water is automatically heated when it is cold and the temperature knob is at "0" position. The process stops when the water is about 30¡ãC.

+ 11 hidden pages