Haier XQB70-A User Manual

Download

User's Manual

DTD 307 XQ

Fuzzy Logic Automatic Washing Machine

Domotech

Please read this manual carefully before using. Retain it for future reference

Please check if the power receptacle has good earthing condition before using to guarantee your safety.

The manufacturer will not bear the responsibility for those risks occurred from not obeying this manual.

Contents

Before using

Names of the parts The 2 cover Safety precautions Installation and adjustment Install the water inlet hose 5

Using process

Preparation before washing Put in the laundries Add the detergent and softener Use the operation buttons Close the top lid Finish washing Disposal after washing

Trouble shooting * Answers to questions

Picking list

Specifications the back cover

10 14 14 15

1 3

7 8 9

Names of the parts

Before using

Top lid B

Detergent box

Control panel

Level meter

Lint filter(Installed by user)

Filter cover

Control panel film

Front control board

Pulsator

Cabinet

Adjustable foot

Top lid A

Drier outlet cover

Power line

Inner tub

hanging hole for the drain hose

back cover

Adjustable foot seam

Cool water valve

Warm watervalve

Back faceplate

Cabinet handle

Drain hose

Front fixed foot

base frame

Rear fixed foot

Accessories

The end connecting to the washing machine

Jointer connecting the water inlet hose to the water faucet

The end connecting to the water inlet hose jointer

Bottom plate

(1 piece)

Water inlet hose

(2 pieces)

Water inlet

hose jointer

(2 pieces)

Tapping screw

ST4x 16

(8 pieces)

Lint filter (1 piece)

Meaning and description of the symbols

Contents marked with

Warning

mark

Forbidding

mark

that symbol are related to the safety of the product and the personal safety of the users. Failure to comply with the instruction could cause damage of the machine or injure the personal safety of the user.

Contents marked with that symbol are actions forbidden to perform. Failure to comply with the instruction could result in damage of the machine or injure the personal safety of the user.

Safety precautions

Before using

Please insert the power cord into special receptacle with rated voltage.Be sure to use single-phase three pins receptacle. The earthing terminal must be earthed reliably.If possible,please adopt electric leakage protector.

Earth

Do not bend, stretch, twist, bind the power cord by force, or reform it. Do not press or clamp it with heavy items. If the power cord and power plug are bad, or the receptacle is loose, be sure to have it replaced by the technicians of our special shop or our agent, or the after-sale service department for the sake of avoiding any risk. Keep the prong of the power plug clean. If dust is found on the power plug, please wipe it off with dry cloth.

In case the washing machine is installed on ground with carpet, be careful not to block the ventilation hole with carpet.

The ventilation holes at the bottom

In normal usage of the washing machine, the power plug shall be ready to be pulled or plugged with hand. Be sure to pull the plug off and close the water faucet in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine. Do not plug or pull the power plug with wet hand.

Do not use water with temperature higher than 50 inside the tub.

Do not set the machine at damp place like the bathroom. Never wash it with water. Do not put wet laundries on the control panel coating.

Do not let the machine share one receptacle with other electric appliances. If the power plug is damaged, or the plugging into the receptacle is loose, do not use it any more.

Do not wash water-proof laundries like the raincoat, bike covers, down textiles etc. to avoid abnormal vibrations in spinning and damaging the laundries.

Safety precautions

Before using

Do not put hand into the rotating tub. It is dangerous even if the rotation speed is slow. Take special care of the children. Keep children away from the washing machine to avoid them climbing on it.

Do not put any hot or heavy items (such as the kettle with hot water) on the washing machine.

Do not decompose, repair or alter the machine by yourself.

Do not wash laundries with volatile materials (such as thinner, petrol etc.).

The handicapped or children shall not use the machine without care.

To prevent the lint in the tub from blocking the cascade outlet and influencing the cascade effect, please keep the lint filter in good condition, and install it to proper position during washing. If the lint filter is lost or damaged, please contact the local after-sale service department of our company.

Keep the machine away from direct sunlight and heat source like the heater.

To protect your laundries and washing machine, please take out all of the coins, buttons, sand, hairpin and other foreign materials before washing.

Please check if the water faucet is open, and if the connection of the water inlet pipe is proper. It is suggested to use foamless washing powder.

Before using

Safety precautions

Please install and adjust the machine according to the requirement of the manual, which is very important for you to operate the machine safely and properly.

Install the bottom plate

After opening the package, please lean the

washing machine gently down on soft items

(like towel cloth, blanket, etc.). Install the

bottom plate to the bottom of the machine

with eight screws by a cross screwdriver,

then lift the machine up gently. See to the

figure:

Adjust the installation position

The largest allowable slope of the shank base of the machine is 2 . The slanting or rough ground will result in unstable running or stoppage of the machine. Please adjust it with following methods:

Bottom plate

Screw

Back

Front

Soft item

Confirm it's horizontal:

If the bulb of the level meter at the balance display position is inside the standard circle, it indicates that the machine is horizontal. Otherwise you need to adjust the adjustable leg of the machine.

Adjust the adjustable leg:

1.To twist the adjustable leg, please first lift up the leg side slightly, loosen the adjustable nut, and then twist the leg.

2.After adjustment, fasten the nut.

Air bubble

Suitable Not suitable

Standard circle

Loosen

High

Fasten

Low

Adjustable nut

Adjustable leg

Before using

Install the lint filter

After opening the package, please take out the lint

filter from the document bag, install it to the filter cover

of inner tub. See to the figure.

Before using

Inner tub

How to change the direction of the drain hose

1.Lean the machine down gently with the front surface facing the ground. Loosen the eight screws by a cross screwdriver.

Back

Front

2.Pull out the drain hose from the groove at the left side.

Use groove at this side after direction changing

Bottom plate

Soft item

3.Extend the drain hose from the left side. Push the

drain hose into the groove with hands.

4.Install the bottom plate (as per indicated before),

then lift the machine up gently.

Page 3

Lint filter

Usage of the drain hose

The drain hose shall drain smoothly

1.The height of the drain hose shall be

less than 10cm, or the drainage will not be smooth, and cost such long time that the machine may stop at mid way.

2.Do not ramp or press the drain hose.

If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly.

4.If extra drain hose is needed, please

make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m.

If the extra hose is too long, cut it either at A or at B point.

Before Using

Install the water inlet hose

Install the water inlet pipe

Water faucet, suitable water faucet, not suitable

It is required that the front end shall be longer than 10mm.

The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage.

Connection between the water inlet hose jointer and the water faucet

1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the

water inlet hose component. See to Figure 1.

2 Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed. Then set the water inlet hose jointer on the faucet. See to Figure 2. If the faucet is too large and the jointer cannot be set on, please loosen the four screws and take out the bush inside the jointer. See to Figure 3.

Water inlet hose jointer

Slider

Nameplate

Lock level

Water inlet hose

3 Fasten the four screws of the water inlet hose jointer evenly. See to Figure 4. 4 Take off the nameplate. Twist the fastening nut as per the indication of the figure

to seal up the exit end face of the faucet. See to Figure 5.

Remark: .Before installation, the threading is 4mm above the upper surface of the nut. After installation, the threading is 2mm above the upper surface of the nut..

Figure 4

Figure 1

Screw knife

Figure 2

Screw nut

Figure 5

Screw

Bushing

Figure 3

About 4mm after twisting About above 2mm after twisting

Figure 6

Connection between the water inlet hose and the washing machine

1 Do not take off the water absorption cushion. Please check if the cushion is dropped or damaged each time before using. If it happens so, please duly contact our after-sale service department. 2 Set the nut of the water inlet hose on the water inlet valve jointer. 3 Fasten the nut. Swing it gently to confirm if it's fastened well.

Water inlet valve jointer

Water inlet hose nut

Water absorption cushion.

Before Using

Connection between the water inlet hose jointer and the water inlet hose

1 Push down the slider. Plug the water inlet hose into the jointer.

2 Hang the lock lever onto the jointer. Release the slider till a click sound is heard.

Locking level

The water inlet hose jointer

Slider

Check the connection between the water inlet hose jointer and the water faucet

1.Swing the hose gently to check if it is fastened stably.

2.After installation, open the faucet to check if it leaks water.

3.Do not bend the hose by force.

4.Each time before using, please check if the connection between the water inlet hose jointer and the water faucet, and the installation of the water inlet hoseis firm, so as to avoid dropping owing to improper installation.

Dismount the water inlet hose

1 Close the water faucet.

2 Press the lock lever and push down the slider. Then pull off the water inlet hose. If the machine is used more than once every week, the water inlet hose jointer can remain on the faucet to avoid damaging the fastening screws.

Lock level Slider

Using process

1Preparation before washing

Preparation before washing

1 Connect the water inlet hose. Open the water faucet.

2 Confirm that the washing machine is earthed reliably.

Then plug the power plug into the receptacle. The

earthing terminal shall not link to gas pipeline and

faucet water pipeline.

3 Put down the drain hose.

Earth

Pay attention to the followings before washing

Check if the laundries have special requirement on washing

A. Check if the laundries are applicable for washing with machine. b. Divide the laundries that are not colorfast from other laundries. c. Put the laundries difficult to absorb water into water with hand. d. For the laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil, please apply detergent on them in advance, which can make it easier to remove the soil. e. For the laundries that may get lint ball and those with long fur, turn it over before putting in. f. Do not put the laundries polluted by chemicals into the washing machine directly.

Clear the pocket. Take out the coins, sand, hairpins etc.

Tie the long strips; fasten the buttons; close zippers.

The quantity of the laundries shall not be too large. Stretch and loosen the laundries before putting them in the tub.

When the pulsator is running ,the buttons of the laundries may cause noise. For the sake of discretion, please put the laundries with buttons into other laundries.

Using process

2 Put in the laundries

The capacity of washing and spinning refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one cycle. Washing quantity for one cycle shall be less than the rated capacity.The largest capacity of this machine is 7.0kg. The thickness, size and type of the cloth will influence the actual washing capacity. It is feasible to put in suitable amount of laundries and the laundries can be tumbled normally in washing for one cycle. Please do not select high water level for laundries less than 2.5kg to avoid splashing. In washing the fluffy laundries like the woolen blanket, the quantity shall not exceed 3kg for each cycle. In using water with high temperature, please pay attention to the washing temperature limit stated on the label of the laundries.

Reference weight of the laundries:

Blanket

cotton,about 900g

Pajamas

about 200g

Shirt

cotton,about

300g

Working suit up,down

Undershirt

cotton,about 180g

cotton,about 1120g

Underpants

cotton,about 70g

Jeans about 800g

blending coat

about 800g

Jacket cotton,about

800g

Single bed sheet

cotton,about 600g

Socking

blending,about 50g

3 Add the detergent and softener

Using process

Put the washing powder and softener into the detergent

Inlet for concentrated washing powder and detergent

box directly as indicated in the left figure. After that, please close the detergent box. Refer to the following table for the usage of the detergent: The standard dosage of the detergent and the water quantity

Using process

Softener inlet

Detergent box

How to use the whitener

Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Do not use whitener on laundries with color or print as they are not colorfast. The whitener shall not touch the laundries directly. Refer to the user's manual for the usage and dosage of the whitener. As to whitener in powder, please dissolve it before using.

How to use the washing powder

Not applicable for fuzzy program and reserve washing Directly dissolved in the machine:

1.Fill in small quantity of water.

2.Add the washing powder. Run for 30 seconds to dissolve it completely.

3.Put in the laundries. Select suitable water level. The instant dissolving of the washing powder:

1.Prepare warm water of 30 and a container.

2.Add the powder into the container while stirring to fully dissolve it. The powder is more likely to pollute the laundries than the detergent. Therefore please use it with suitable quantity. It is suggested not to use high sudsing detergent. Washing powder with poor quality or long time storage may be caked. Please pay attention to cleaning the detergent box in time.

Standard dosage of the detergent and water quantity

Laundries quantity (kg)

Below 1.0

Water level

Water quantity

About 66L About 61L

About 57L About 76g About 47.5g About 53L About 70.7g About 44g

About 49L About 65.3g About 40.8g About 44L About 58.7g About 36.6g

About 40L About 53.3g About 33.3g About 34L About 45.3g About 28.3g

About 30L About 40g About 25g About 23L About 30.7g About 19g

Common powder, Add 40g in each 30L water

About 88g About 55g About 81.3g About 50.8g

Concentrated powder,

Add 25g in each 30L water

Using process

4 Use the operation buttons

a Description of the function of the operation buttons

Mode and meaning of the indicator

Flash: indicating the running mode On: indicating the mode about to run Flash rapidly: indicating abnormal situation

Balance display

If the bulb of the level meter is inside the standard circle, it indicates that the machine is horizontal.

Balance display

WATER INLET button

In starting the machine, it is set to COOL WATER automatically Push the button to select one from the three modes of COOL WATER only, both WARM WATER and COOL WATER, or hot water only. Note that the water temperature inside the tub shall not exceed 50 .

Cool water

Cool water Warm water

Warm water

No requirement on water temperature

If the hot water temperature is too high and needs to be mixed with cool water

When the temperature of hot water is suitable, or when you need to improve the water temperature inside the tub

WATER LEVEL button

Select the fuzzy program. After cloth detection, the water level will be set to one out of 4, 6, 8, and 10. If there's water inside the tub, the machine cannot detect the cloth and will display water level 6 If wet laundries are put in, it may display water level 10 You can also set water level by self. After the machine is started, it will not detect the cloth. If quick program is selected, the water level will be set to 2 automatically. When level is reached, it will perform washing while filling water. The 2 water level indicator is on, and the 4 water level indicator is flashing. When the “4” water level is reached, it will stop filling water. 2 level indicator is off, and 4 level indicator is on. It will perform normal washing.

STRONG

COOL

WATER

INLET

WATER

LEVEL

CURRENT

CURRENT button

When the washing machine starts running, it will set the current automatically. You can select current by self according to the actual requirement. Please do not select strong current under low water level to avoid splashing and vibration. In FAST and GENTLE programs, the washing machine will set the current automatically, and the users cannot select current in that case.

Using process

Digitron

During sensing, it displays -During operation of programs, it displays the remained time (minute) During reserve procedure, it displays the remained reserve time (in hour) In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16)

START/PAUSE button

After the power is switched on, push it to start the machine During working, push it to pause working. During pause, push it to resume working.

POWER ON/OFF button

Push the On/Off button to switch on the power. When the power is on, push it again to switch off the power.

FUZZY

SOAK

WASH

RINSE

SPIN

SELECT

SURPLUS

RESERVE

STANDARD

NIGHT

GENTLE

HOURS LATER

FAST

PROGRAM

RESERVE button

Push the button to select washing finishing time between 2-24 hours. When the RESERVE function is activated, the RESERVE and TIME REMAIN indicators are on. The other indicators are off. Push the RESERVE button to display the reserve mode.

START PAUSE

POWER ON/OFF

SELECT button

Push it to select one or more programs from SOAK WASH RINSE and SPIN

PROGRAM button

The following four programs are available for your option

Standard Common washing

Night Low noise washing during night

Program

Gentle Washing the woolen textiles or underwear

FAST 10-minute quick washing of laundries with light soil

Remarks: Push the On/Off button to switch on the power. If the washing machine is idle for 5 minutes, it will automatically switch off the power.

Using process

B Steps of using the operation buttons and description of each step.

BALANCE DISPLAY

MIN

HOURS LATER

FUZZY

STANDARD

NIGHT

GENTLE

FAST

PROGRAM

SOAK

WASH

RINSE

SPIN

SELECT

START

PAUSE

POWER ON/OFF

STRONG

COOL

WARM

WATER

INLET

WATER

LEVEL

SOFT

CURRENT

SURPLUS

RESERVE

1 Push the POWER ON/OFF button to switch on the power.

2 Push the program button to select suitable automatic program.

After switching on the power, the machine will set standard program automatically. To select other automatic program, push the PROGRAM button till the relative indicator is on. Refer to the PROGRAM button on Page 11 for the selection. For instance: select QUICK program for laundries with small quantity and light soil.

Page 11

In selecting the standard and night programs, the

STANDARD

machine will execute fuzzy program to select water level and wash time according to the cloth and weight of the laundries. The full procedure is

PROGRAM

controlled automatically.

3 Push the select button to select suitable procedure.

SELECT

After switching on the power, the washing machine will set to WASH-SPIN procedure automatically. It is the common procedure. To select other procedures, push the SELECT button to select one or more procedures from SOAK, WASH, RINSE AND SPIN. Refer to PROCEDURE SELECTION METHOD to make selection.

Page 13

FUZZY

NIGHT

GENTLE

FAST

Attention

Using process

Even there's no water in the tub, a certain period is required before spin starting. Do not use the SOAK program for the woolen textiles. Separate the laundries that are not colorfast from other laundries in washing.

Procedure selection method

Using process

Times of pushing the SELECT button

Push the SELECT button for 6 times, and it will resume the initial mode. It will circulate in that sequence. The SOAK procedure can work in cooperation with automatic programs like standard and night. There is intermittent pulsator stirring during soak.

Selected procedure

WASH - SPIN

WASH (the washing liquid remains in the tub)

WASH - RINSE

(the rinsing liquid

remains in the tub)

RINSE - SPIN

Spin

(spin after drain)

SOAK - SPIN

Applicable circumstance

When the common laundries need washing, rinsing and spinning.

Repeat using the washing liquid

When prevent the laundries from corrugating, and the laundries do not need spinning

When the laundries need rinsing and spinning after manual washing

When the laundries need only spinning after manual washing (first drain then spin)

The laundries are very dirty, or the sleeves and collars of the shirt are very dirty. First soak then wash.

Contents (the lighted indicators indicate the programs about to run)

SOAK WASH RINSE SPIN

4 Push the WATER INLET button to select water inlet mode

After the power is switched on, the washing machine will set to COOL WATER inlet mode automatically. To select WARM WATER only or both COOL WATER and WARM WATER, push the WATER INLET button to make selection. See to WATER INLET in Page 10 for details.

Page 10

WATER

5 Push the WATER LEVEL button to select suitable water level

After the power is switched on, the washing machine will execute fuzzy program automatically to detect the cloth. After defection, it can set the water level automatically. To select other water level, push the WATER LEVEL button to set the water level. Refer to STANDARD DOSAGE OF DETERGENT AND WATER QUANTITY in Page 9 and WATER LEVEL in Page 10 for selection.

Page 9

Page 10

LEVEL

Using process

Water Level and Time Table of Each Program

Program

Standard

Night

Gentle

Fast

* Total time: including the normal water inlet time and drain time. * Wash time: adjustable according to the water temperature automatically. * Spin time: the time from intermittent running to finishing * The standard and night programs can have SOAK procedure. After water inlet, it will first perform soaking for about 15-35 minutes along with slightly pulsator stirring, and then do washing. * The washing finishing time may be influenced by the water inlet pressure.

Water

level

About 4 About 3

Wash

(minute)

Rinse (minute)

Rinse twice

Spray twice,

rinse once

Rinse once

Spin

(minute)

About 5~6 About 6~8

About 2 About 2

Total time (minute)

Soak included Soak excluded

About 83~45 About 48~30

About 99~55 About 65~40

About 21~17

About 10

6 Push the CURRENT button to select suitable water current

After the power is switched on, the washing machine can set the current automatically according to the laundries. If you need to select current by yourself, please push the CURRENT button. Refer to CURRENT in Page 10 for details.

Page 10

7 Push the RESERVE button to select suitable reserve wash program

After the power is switched on, the reserve program is set to off mode automatically. If you need to set the washing procedure to be finished at reserved time, please push the RESERVE button to set the reserve wash program. Refer to RESERVE BUTTON in Page 11 for selection.

Confirm the operation of reserve program

When the RESERVE function is activated, the indicator of the program you have set will be off. The RESERVE (HOUR) and TIME REMAIN indicators will be on. During reserve procedure, you can push the RESERVE button to display the reserve mode. To change the running program or cancel the reserve setting, you need to switch off the power and make new selection.

The washing will be finished after 18 hours.

8 Push the START/PAUSE button

5 Close the top lid.

6 The washing is finished.

RESERVE

Reserve time from 2 to 24 hours

START PAUSE

If you open the top lid, the machine will stop working before spinning.

It beeps to indicate the finishing of washing

The power will be switched off automatically after the finishing of the washing.

7 Disposal After Washing

Using process

Please take off the detergent box and wash it with water

1.How to take it off: Pull it upwards slantingly and gently.

2.How to install: Put it in from the top slantingly, then push

it in to the right position.

The filter screen is likely to be blocked by foreign

materials and influence water inlet. Please clean it

with brush frequently.

Lint filter:

1.Pull it up to dismount.

2.Push it down to install it.

3.After washing, clean the filter screen

Dismount and installDismount CleanInstall

If the cabinet is dirty, wipe it with wet soft cloth

Do not wash with water directly.

Wipe with neutral detergent.

Do not wipe with thinner, petrol, alcohol, etc.

1.After washing, close the water faucet. (If desired, dismount the water inlet hose).

2.Do not store water in the washing machine for a long period. Drain the water completely after each using.

3.Be sure to pull off the power plug before maintenance.

4.Hang up the power cord and drain hose.

5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (about 1 hour), then close the top lid.

Trouble-shootingAnswers to questions

(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself.

Phenomenon Reason How to solve

It rings after starting the reserve function. The digitron displays E0.

The drainage cannot work, or is too slow. The digitron displays E1 and it rings.

After washing and rinsing, it stops running during spinning. The digitron displays E2 and it rings.

The safety switch acts, and the spinning cannot work (after twice automatic imbalance revising). The digitron displays E3 and it rings.

The water inlet does not work, or is too slow (cannot reach the water level after about 15 minutes). The digitron displays E4 and it rings.

The water temperature is too high. The digital tube displays E5, and rings.

The cascade current is poor or there's no cascade current.

The machine does not act.

There's abnormal sound inside the machine

The water faucet leaks water

No water inlet.

Not wash

Not spin

Common phenomena

The top lid is opened.

Is the drain hose blocked?

The top lid is not closed.

Are the laundries put slantingly? Is the machine slanting?

Is the water faucet opened, or is there water supply failure? Is the water inlet valve blocked?

The temperature is higher than 60 C.

Is there foreign material blocking the spray outlet?

Is there power failure? Is the power plug inserted tightly? Is the water level reached preset position?

Is the power plug inserted tightly? Is the top lid closed reliably? Are the laundries set flat?

Is the machine slanting? Are there any foreign materials? Are the laundries put slantingly in spinning?

Is the screw of the water inlet hose jointer loose? Is the screw of the water inlet hose jointer twisted awry?

Is the power plug plugged tightly? Is the water faucet opened? Are the POWER ON/OFF and START/PAUSE buttons pushed down?

Close the top lid.

Clean the foreign material. Push the start button again.

Close the top lid.

Reorder the laundries. Close the top lid. Set the washing machine horizontally and then open and close the top lid once.

Open the water faucet. Push the Start/Pause button again. Clean the water inlet valve then push the Start/Pause button again.

After cooling. Press the Star/Pause knob.

Clear the foreign material.

Please use it when there's power supply. Insert the power plug tightly. Fill water to the preset position.

Insert the power plug tightly. Close the top lid. Set the laundries flat.

Adjust the machine to be even Remove the foreign materials. Reorder the laundries and close the top lid.

Fasten the screw of the jointer properly.

Plug the power plug tightly. Open the water faucet. Push the power ON/OFF button and START/PAUSE button.

Phenomena Explanation

The spinning is intermittent when it starts.

The wash procedure pauses.

Push the SPIN button, but it doesn't act.

The pulsator pauses during water filling in washing and rinsing.

There may be some water flowing out of the drain hose in the first use of the machine.

In adding water, the pulsator performs stirring slightly

It is to balance the laundries to avoid slanting.

The cloth sensor is detecting the cloth. It will start adding water after about 48 seconds.

The program is setting the drain time. A certain period is needed before it starts spinning.

It is to avoid splashing during water filling.

It is the water remained in the machine during the ex-factory performance inspection.

It is to soak the laundries more completely.

Packing list

Name

User's manual

Lint filter

Water inlet hose component

Bottom plate

Tapping screw, ST4x16

Fuzzy logic automatic

washing machine

Quantity

1 piece

2 pieces

1 piece

8 pieces

1 set

Storage position

Inside the document bag

Inside the accessory bag

Between the upper cushion of the washing machine package and the upper seal of the package carton

Inside the accessory bag

Specifications

Model

Rated voltage frequency

Rated washing / spinning capacity

Water level/Water quantity (about)

Max water consumption

Water inlet pressure

Rated washing power

Rated spinning power

Weight

Dimensions (mm)

DTD 307 XQ

220V ~ 50Hz

7.0kg

1/23L, 2/30L, 3/34L, 4/40L, 5/44L,

6/49L, 7/53L, 8/57L, 9/61L, 10/66L

About 186L (the highest water level, standard program)

0.03MPa-0.78MPa (when water temperature is 70 ~90 , the water inlet pressure of hot water shall not exceed 0.4MPa)

380W

260W

About 38kg

L 610 W 555 H 945

Haier XQB70-A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual