Haier XPB65-27QGS User Manual

User's manual

XPB65-27QGS

Twin-tub Washing Machine

Contents

Before using

Names of the parts.............the 2 cover

Safety precautions ...............................1

Installation and adjustment ..................3

Introduction of the major functions .......5

Using process

Preparation before washing ................6

The musts in washing .........................7

Usage of the detergent .......................8

Washing sequence ..............................9

Disposal after washing .......................13

Trouble-shooting*
Answers to question

Packing list ......................................16

.....................15

nd

Please read this manual carefully before using.
Please retain it for future reference.

Specification

..............the back cover

Names of the parts

Buzzer
Water-filling entrance
Water inlet selector handle
Wash selector
Wash timer
Control panel
Overflow filter
Water level adjusting lever
Drain hose hanging hole
Lint filter
Valve cover
Pulsator
Wash tub
Drain hose
Base frame

Before Using

Before Using

Outer cover of the spin tub

Inner cover of the spin tub

Spin timer

Spin tub frame

Spin tub

Cabinet

Power cord

Accessories

Water inlet hose

(1 piece )

Gland

(1 piece )

Meaning and description of the symbols

Warning sign

Prohibition sign

Contents marked with that symbol are related to the safety of

the product and the personal safety of the users. Please operate

in strict conformity to the contents.

Contents marked with that symbol are prohibited, otherwise it

may do harm to the washing machine or the personal security

of the operator.

Safety precautions

Before Using

Before Using

Be sure to use three-phase receptacle.
Earth the earthing terminal of the
receptacle reliably.

Earth

If the power cord is bad, to avoid risk it is required to replace it by the technicians of
our special shop or the after-sale service department. Keep the pin of the power
plug clean.

In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.

When the machine is normally using, please
put the power plug at the location easily to
be inserted and extracted by hand. Be sure
to pull the plug off when there'spower failure,
or the machine is being moved, cleaned or
when it is idle.

Do not use water hotter than 50 C .

Ventilation hole at
the bottom of the
washing machine

Do not put the machine at damp place
like the bathroom . Never wash it with
water. Do not place wet laundries on the
control panel.

Do not share one receptacle with other
electric appliances. Do not use it in
case that the power plug is damaged
or the inserting into the receptacle is
loose.

Do not wash water-proof laundries such
as the raincoat, bicycle shelter etc. To
avoid abnormal vibration during spinning.

Safety precautions

Before Using

Before Using

Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.

Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.

Do not decompose, repair or alter the
machine by yourself.

Do not wash laundries with volatile
materials (such as thinner, petrol etc.).

Handicapped or children without care
shall not use the machine.

Petrol

Thinner

Keep the machine away from direct
sunlight and heat source like the
heater.

Before Using

Installation and adjustment

Before Using

Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.

Usage of the drain hose

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall be
less than 10cm , or the drainage will
not be smooth enough and cause
incomplete drainage.

<10cm

2.Do not step on or press the drain hose.

3 If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.

4.If extra drain hose is needed , the inner
diameter of the extra hose shall not less
than 30mm, and the length shall not exceed

1.5m.

> 30mm

<1.5m

Install the water inlet hose; Select the water level

Insert the water inlet hose into the water-filling
entrance on the control panel directly. (pull it
out to dismantle it)

Select water level according to the
quantity of the laundries.

Adjust the water level adjusting
lever to desired water level line.

Attention:
In water filling, do not exceed
the"High" water level. Otherwise
the water may overflow out of the
washing machine.

High

(about 55L)

Medium

(about 46L)

Low

(about 36L)

Water inlet hose

Water level
adjusting lever

High

Medium

Low

Water-filling
entrance

Before Using

Before Using

How to change the direction of the drain hoses

Figure 1 indicates the ex factory
installation position of the drain
hose.

Extend the drain hose from the side of spin tub.

Take off the drain hose from the hanging
hole of the cabinet. Pull the drain hose
fixing hook outwards gently to take out
the drain hose from the two fixing hooks.
(As per Figure 2)

Rotate the drain hose fixing hook for 90
to take it out from the installation hole
(As per Figure 3).

Install the two drain hose
fixing hooks taken out into
the installation hole at the
other side of the base frame
(to aim at the installation
hole accurately you can

Rotate the fixing
hook for 90

lean the washing machine
forward slightly).Then rotate
for 90 (As per Figure 4).

Take off the fixing
hook downwards

Pull the fixing hook outwards slightly.
Inlay the drain hose into the fixing hooks
reliably along the groove at spin tub side,
and make it extend towards spin tub side.

Drain hose
fixing hook

Pull outwards
slightly

Figure 3

Drain hose
fixing hook

Side sectional view

Take off
the drain hose

Rotate the fixing
hook for 90

to fix it

Insert the fixing hook into the
installation hole upwards

Figure 1

Fixing hook
installation hole

Drain hose

Figure 2

Figure 4

Then hang the drain hose into the hanging
hole at the spin tub side. (As per Figure 5).

Extend the drain hose from the rear side

Take out the drain hose from the fixing
hook. Extend it from the rear side (When
the drain hose is extended from the rear
side, it can be hung on the point for drain
hose at the two sides of the cabinet.)
(See to Figure 6).

Figure 5

Figure 6

Using process

Introduction of the major function

The machine has good comprehensive performance, and nice appearance.

It adopts streamline appearance and full plastic shell, which will never get rust.

For the design on safety and reliability, it adopts the wash shelf and water reception

groove design, and reduces the unfavorable influence on the electrical component by the

vapor. Therefore it guarantees more safe and reliable washing.

It adopts complete enclosed base frame and low-noise motor, and thus reduces the

working noise significantly. We can guarantee that the purchase of this machine will bring

you a clean world without disturbing your quiet life.

Using process

Foam-removing spinning during high-efficiency rinsing

Use the foam-removing spinning to

remove the extra detergent liquid. It can

both shorten the washing time and save

the water consumption.

Remove most of the foam
extra detergent liquid. it can
both shorten the washing
time and save the water
consumption.

Spin

Spin for about
1~2 minutes

Fill water for
about 1 minutes

Remove the detergent
liquid remained

The effect is best when the
laundries quantity is below
80% of the rated value.

Foam-removing
spinning

Spin for about
1~2 minutes

Preparation before washing

Preparation before washing

1.Connect the water inlet hose.

2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.

3.Put down the drain hose .

4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.

Using process

Using process

Pay attention to followings before washing the laundries

Confirm if
there's special
requirement for
the laundries.

Clear the pocket.
Take out the
coins , sand,
hairpins etc.

Fasten the
buttons and
zippers.

The quantity of
the laundries
shall not exceed
the rated value.
The big laundries
like the jeans
shall be put in
loosely.

When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion,please
put the laundries
with buttons into
other laundries.

The musts in washing

The capacity of washing and spinning of
the machine refer to the largest weight of
the standard laundries under dry condition
that can be washed or spinned in one time.
Laundries quantity in one washing cycle
shall be lower than the rated capacity.
The largest capacity of this machine is

6.5 kg.
The thickness ,size , type of the cloth will

influence the actual washing capacity. It
is suitable to put in reasonable amount of
laundries and the laundries can be turned
round in washing for one time washing.

Do not select " High " water level for
laundries less than 3.2kg, so as to avoid
splashing of water.

Reference weight of the laundries

Using process

Using process

cotton,about 900g

Pajamas

Shirt

cotton,about

300g

Working suit up,down

Blanket

Undershirt

cotton,about 180g

cotton,about 1120g

Underpants

cotton,about 70g

Jeans about 800g

Blending coat

about 800g

Jacket

cotton,about

800g

Single bed sheet

cotton,about 600g

Socking

blending,about 50g

Using process

Usage of the detergent

Using process

How to use the whitener

Fill water to decided level. Dilute the whitener with container. Pour it slowly into the
washing tub.
Avoid using whitener on laundries with color or pattern as they are prone to lose color.

The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and quantity of the whitener.

For powder whitener, please dissolve it before using.

How to use the washing powder

Direct dissolved in the machine:

1.Fill small quantity of water.

2.Add the powder . Run for 30 seconds to
dissolve it completely.

3.Put it in the laundries. Select suitable
water level.

The instant dissolving of the washing powder:

1.Prepare warm water of 30 C and a container.

2.Add the powder while stirring to fully
dissolve it.

The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.

It is suggested not to use high sudsing
detergent.

Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.

Selection of the quantity of the washing powder list 1

Standard dosage

Laundries
quantity

4.5kg~6.5kg

2.5kg~4.5kg

Below2.5kg

Water level

Water quantity

High (about55L)

Medium (about46L)

Low (about36L)

Concentrated washing
powder

About About

About About

About About

46g

38g

30g

Common washing
powder

55g

46g

36g

Selection of the current , water level and washing time list 2

Laundries
quantity

3.2kg~6.5kg

Below3.2kg

Current

Standard

Gentle

Water level

Water quantity

Medium (about46L)
~

High (about55L)

Low (about36L)
~

Medium (about46L)

Laundries

Knitwear
Cotton,blending,linen
Very dirty and thick
Bed sheet
Silk(thin laundries)
Chemical fiber
Cotton,blending,linen

Washing time
(minutes)

About3~6
About8~10
About10~13
About7~13
About2~4
About3~6
About8~10

Washing sequence

Using process

Using process

Water-filling selector handle

Overfilling sign

Wash timer

(To set to below 2 minute,
first set to 5 minute then
turn it back. it can increase
the service life of the timer).

OFF

WASH TIMER

LINEN

(gentle current,
standard current)

WOOL

SILK

COTTON

Wash selector

STANDARD

GENTLE

WASH SELECTOR

Water-filling entrance

DRAIN

MAX

BUZZER

Wash

1.Water-filling selector
(1) Set the water-filling selector at the "WASH" side.
(Figure 1)
(2) Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.

Buzzer

(The buzzer will ring when
the washing finishes)

OFF

Spin timer

(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).

OFF

SPIN TIMER

SPIN

WASH

Figure 1

Figure 2

2.Put in the laundries. If the water quantity is
insufficient, please add water.

3.Select the current.
Select the" STANDARD" or "GENTLE "current
according to the laundries. (Figure 3)

4.Select the washing time
Select the washing time according to the laundries.
(Figure 4)

5.After washing, the buzzer will ring. Set the "WASH
SELECTOR" at "DRAIN". (Figure 5).

STANDARD

GENTLE

WASH SELECTOR

WASH TIMER

STANDARD

GENTLE

WASH SELECTOR

OFF

WOOL

LINEN

DRAIN

SILK

COTTON

DRAIN

Figure 3

Figure 4

Figure 5

Midway spinning

1.

Put the laundries into the spin tub evenly and smoothly.

2.

Spin

(1) Put the gland in properly.

Please put in the gland properly even if the laundries quantity is smal.l

Using process

Using process

Push

Proper Proper

(2) Close the inner and outer cover of the spin tub.

(3) Spin for 1-2 minutes.

3.

Run the foam-removing spinning.

(1) Open the outer cover of the spin tub.
(2) Set the water-inlet selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
(3) Close the outer cover of the spin tub. Spin for 1-2
minutes.

Gland

The laundries
are slanting

Push

No gland

Outer cover of
The spin tub

Inner cover of
The spin tub

WASH

SPIN

Rinsing

Rinse with water-filing

Using process

Using process

1.Put the laundries into the wash tub. Select
suitable current according to the laundries.

2.Adjust the water level
According to the laundries quantity, set the
water level with the adjusting lever. Fill
suitable water consecutively.

3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.

Rinse with stored water

1. Put the laundries into the wash tub. Select suitable current according to
the laundries.

(Repeat the midway spinning and
rinsing with stored water for 2-3 times)

OVERFILL

If the water flows out
of the overfill holes,
that is overfilling

2. Fill water to preset water level.

3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.

When the laundries quantity is below 3.2kg, please use "Gentle" current.
If you use "Standard" current, it may splash.

Spinning

Using process

Using process

1. Put the laundries into the spin tub
evenly and smoothly.

2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.

3. Spin
Select suitable spin time according
to the laundries, and do spinning.

During spinning, if there's abnormal
sound, it is generally owing to
slanting placement of the laundries.
Please stop the machine and re-order
the laundries.

In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.

Selection of the spin time list 3

Laundries

Bed sheet or
blanket

Underwear
(knitwear)

Swear
(chemical fiber)

Blending thin
laundries

Spin time
(minutes)

About 4~5

About 2~4

About 1~2

Within 1 minute

To do spinning and draining or rinsing
with water-filling together, please first
do spinning for around 1 minute, then
do draining or rinsing with water-filling.
Otherwise the spinning will stop owing
to too much water stored in the spin tub.

Using process

Disposal after washing

After using, please clean the lint and foreign materials of the lint filter and lint frame
in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.

Using process

Cleaning the lint filter

The lint filter must be used during washing.
It must be cleaned in time after each using.

1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See to
Figure 1)

2. Clean the lint
Put it in water and clean while it is
still wet.(See to Figure 2)

Figure 1

3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the filter frame,
then push the upper part of the
filter in ( marked with " up side ").
(See to Figure 3)

Cleaning the filter frame

Too much lint on the filter frame will influence
the normal usage of the machine. Please
clean it every two months.

1 Take off the filter frame.
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.

Figure 2

Figure 3

Elastic fixing
claw

Cleaning the filter frame

2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter (See to Figure 1).

3. Cleaning the filter frame
Clean the lint around the frame
and flush with tap water.

Using process

Using process

Water level
adjusting lever

Figure 1

Corrugation
Pipe

4. Install the filter frame.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the frame into
the valve cover.
(3).Hang up the hook at the left
upper side.
(4).Push the upper part in as
indicated in Figure 2.

Disposal of the complete unit

Wipe the complete unit with soft cloth

twisted dry.

Wipe with neutral detergent if too dirty

Do not wash it directly by water

Thinner

Petrol

Alcohol

After washing, dismount the water inlet
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.

Hook

Figure 2

Trouble-shooting Answer to question

(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.

Phenomena The reason

Is there power failure?

The machine does not act.

The draining does not work

Is the power plug loose?
Is the pulsator twisted by foreign materials?

Is the drain hose put down?
Is the drain hose frozen?
Is the drain hose blocked by foreign material?

There's abnormal sound
during washing

There's abnormal sound
and violent vibration
during spinning

There may be some water
flowing out of the drain
hose in the first use of
the machine.

Are there hair pin, coins or metal items brought
inside the tub?

Is the machine slanting?
Is the gland pressed evenly?
Are the laundries in spin tub too much?

It is the water remained in the factory inspection
of performance.

When the remained water is frozen

Prevent the freezing (be sure to discharge the water completely after using)
After complete draining, set the "WASH SELECTOR" at "GENTLE" or "STANDARD".
If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.

When the water is frozen
Pour hot water below 50 into the wash tub
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.

Below 50 c

2~3L

Packing list

User's manual

Water inlet hose

Gland

Twin-tub washing machine

1 Pc.

1 Pc.

1 Pc.

1 Set