Twin-tub Washing Machine
This manual is for
XPB60-CS
User's manual
Please read this manual
carefully before using.
Retain it for future reference.
The machine is for cold water
connection only.
0030507957
Contents
Contents
Names of the parts
Safety precautions
Installation and adjustment
Preparation before washing
The musts in washing
Usage of the detergent
Washing sequence
Midway spinning
Rinsing
Spinning
Disposal after washing
Trouble-Shooting Answer to questions
Packing list
Specification
The 2nd cover
The back cover
17
Names of the parts
Buzzer
Water-filling entrance
Water inlet selector handle
Wash selector
Wash timer
Control panel
Overflow filter
Water le vel
adjusting lever
Quick water-filling
entrance
Lint filter
(Installed by user)
Pulsator
Wash tub
Wash tub cover
Meaning and description of the symbols
Outer cover of the spin tub
Inner cover of the spin tub
Spin timer
Spin tub frame
Spin tub
Cabinet
Base frame
Contents marked with that symbol are related
Warning sign
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Forbidding sign
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
1
Safety precautions
Please insert the power cord into
special receptacle with rated voltage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
Please use a power point flat has
easy access. Be sure to pull the
plug out when there's power
failure, or the machine is being
moved, cleaned or when it is idle.
adopt electric leakage protector.
Earth
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of an after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
Do not use water hotter than 50 C .
In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.
Ventilation hole at
the bottom of the
washing machine
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plug in the
receptacle is loose, do not use the plug any
more.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
2
Safety precautions
Do not put your hands into the
working machine. It is dangerous
even if the rotation is slow. Take
special care of the children.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Children without care should not use
the machine.
Do not dismantle, repair or
alter the machine by yourself.
Do not wash laundries with volatile
materials (such as thinner,
petrol etc.).
Petrol
Keep the machine away from direct
sunlight and heat source like the
heater.
inner
Th
To protect your laundries and washing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
3
Please check if the water faucet
is open, and if the connection of
the water inlet pipe is proper.
It is suggested to use foamless
washing powder.
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
of the machine.
Install the lint filter
After opening the package,please take out the lint
filter from the document bag,install it to the overflow
filter of the wash tub.See the figure.
Overflow filter
Lint filter
Install the water inlet hose; Select the water level
Insert the water inlet hose into the
water-filling entrance on the control
panel.
Select water level according to the
quantity of the laundries.
Set the water level adjusting
lever to the required line.
Maximum
Medium
Minimum
Quick water-filling entrance
You can fill water into the wash tub
directly through this entrance. It can
reduce the humidity inside the control panel
significantly and prolong the operating life of
the components.
Insert the water inlet hose into the
water-filling entrance, then push the
water-filling jointer into the quick
water- filling entrance. (To dismantle
the water inlet pipe, just push the
control handle as indicated in the figure
and pull it out)
Water inlet hose
Water level
indicator
Max
Med
Min
Quick water-filling entrance
Water inlet hose
Water inlet jointer
Push
Control handle
Quick water-filling
Water inlet
entrance
4
Installation and adjustment
How to change the direction of the drain hoses
Figure 1 indicates the ex factory
installation position of the drain hose.
Extend the drain hose from the side of wash tub
Put soft items on the ground. Lean
the machine down gently with the
Soft item
Figure 1
Back
Front
front surface facing the ground.
Take off the drain hose from the
cabinet.Take the hose out of the
fixing groove.(See to Figure 2).
Embed the drain hose into the groove
Figure 2
along the side of the wash tub in the
order of (1)~(3), heading for the side
of the wash tub. (See to Figure 3).
Embed the drain hose into the
groove with hands. Take care
not to damage the drainhose in
fastening the fixing clamp.
Extend to the
spin tub side
Embed into the
groove in turn
Figure 3
Extend the drain hose from the rear side
Take out the drain hose from the fixing groove.Extend it from the
rear side as per the direction of the arrow.
(See to Figure 4).
Usage of the drain hose
Before using , hang up the drain hose
in a suitable location. Do not put the
drain hose on the ground.
Confirm the end of drain hose is higher than
the level of tub .
5
Figure 4
0.8 H 1.2m
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Before using , hang up the drain hose on
suitable location.
Do not put down the drain hose on the ground.
0.8m H 1.2m
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to the following before washing the laundries
Check if
the laundries
has special
washing
instructions.
Clear the
pocket. Take
out the coins,
sand, hairpins
etc.
Tie the
long strips;
fasten
the
buttons;
close
zippers.
The quantity
of the
laundries
shall not be
too large.
Stretch and
loosen the
laundries
before
putting them
in the tub.
When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion, please
put the laundries
with buttons into
other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent
on them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur,
turn it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
6
The musts in washing
The capacity of washing and spinning of
the machine refer to the largest weight
of the standard laundries under dry
condition that can be washed or spinned
at one time. The laundry quantity in one
washing cycle should be lower than the
rated capacity.
The thickness ,size , type of the cloth will
influence the actual washing capacity. Be
careful to put in a reasonable amount of
laundry.
Do not select" Maximum" water level for
laundries less than 2.4kg, so as to avoid
splashing of water.
It is suggested not to use high sudsing
detergent.
Usage of the detergent
How to use the whitener
Fill water to decided level.
Dilute the whitener with
container. Pour it slowly
into the washing tub.
Avoid using whitener on
laundries with color or
pattern as they are prone
to lose color.
The whitener shall not
touch the laundries
directly.
Refer to the user's manual
for the usage and quantity
of the whitener.
For powder whitener,
please dissolve it before
using.
How to use the washing powder
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute
the laundries than the detergent. The
refore please use it with proper
quantity.
Dosage of different washing powder
is different. Please refer to the
instruction of the washing powder for
the detail dosage.
7
Washing sequence
Water-filling selector handle
Wash timer
(To set to below 2 minute,
first set to 6 minute then
turn it back. it can increase
the service life of the timer).
OFF
WASH TIMER
STRONG
STANDARD
WASH SELECTOR
Wash selector
(standard current,
strong current)
Water inlet
DRAIN
WATER INLET
Overfilling sign
Buzzer
(The buzzer will ring when
the washing finishes)
OFF
MAX
BUZZER
Wash
1.Water-filling selector
(1) Set the water-filling selector at the "WASH"
side.(Figure 1)
(2) Set the water level adjusting lever to
needed line.
2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.
Page10
3.Put in the laundries. If the water quantity is
insufficient, please add water.
4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)
5.Select the washing time
Select the washing time according to the
laundries. (Figure 4)
6.After washing, set the "WASH SELECTOR"
at "DRAIN". (Figure 5).
WASH SELECTOR
Spin timer
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
SPIN TIMER
SPIN
SPIN
WASH
WASH
Figure 1
Figure 2
STRONG
STANDARD
OFF
WASH TIMER
STRONG
STANDARD
WASH SELECTOR
OFF
DRAIN
Figure 3
Figure 4
DRAIN
Figure 5
8
Midway spinning
Midway spinning
1.Put the laundries into the spin tub evenly and smoothly.
2.
Spin
(1) Put the gland in properly.
Please put in the gland properly even if the
laundries quantity is small.
Push
Gland
Push
Proper Proper
(2) Close the inner and outer cover of the spin tub.
(3) Spin for 1-2 minutes.
3.Run the foam-removing spinning.
(1) Open the outer cover of the spin tub.
(2) Set the water-filling selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
(3) Close the outer cover of the spin tub.
Spin for 1-2 minutes.
The laundries
are slanting
Outer cover of
The spin tub
Inner cover of
The spin tub
No gland
WASH
SPIN
9
Rinsing
Rinsing
Rinse with water-filling
1.Put the laundries into the wash tub. Select
suitable current according to the laundries.
2.Adjust the water level
Set the water level with water level adjusting
lever according to the laundries quantity.
Then fill suitable water continuously.
3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.
OVERFILL
If you find water flowing out here,please
twist the water tap to
limit the water filling.
Rinse with stored water
1. Put the laundries into the wash tub. Select suitable current
according to the laundries.
2. Fill water to preset water level.
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is below 2.4kg, please use "Standard"
current. If you use "Strong" current, it may splash.
(Repeat the midway spinning and
rinsing with stored water for 2-3
times)
10
Spinning
Spinning
1. Put the laundries into the
spin tub evenly and
smoothly.
2. Press the gland in the tub
properly. Close the inner
and outer cover of the spin
tub.
3. Spin
Select suitable spin time
according to the laundries,
and do spinning.
During spinning, if there's abnormal
sound, it is generally owing to slanting
placement of the laundries. Please
stop the machine and re-order the
laundries.
In spinning, it will pause the work if you open the outer cover of
the spin tub. Close it to resume the spinning.
Selection of the spin time list 3
Laundries
Bed sheet or
blanket
Underwear
(knitwear)
Sweater
(chemical fiber)
Blending thin
laundries
To do spinning and draining
or rinsing with water-filling
together, please first do
spinning for around 1 minute,
then do draining or rinsing
with water-filling. Otherwise
the spinning will stop owing
to too much water stored in
the spin tub.
Spin time
(minutes)
About 4~5
About 2~4
About 1~2
Within 1 minute
11
Disposal after washing
After using, please clean the lint and foreign materials from the
lint filter and overflow filter each time. Otherwise it may affect
the use of the machine.
Please first pull out the power plug from the receptacle before
cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned after each wash.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See
Figure 1)
Figure 1
2. Clean the lint
Put it in water and clean while it is
still wet.(See Figure 2)
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the overflow filter ,
then push the upper part of the
filter in ( marked with " up side ").
(See Figure 3)
12
Figure 2
Figure 3
Disposal after washing
Cleaning the overflow filter
Too much lint on the overflow filter will influence
the normal usage of the machine. Please
clean it every two months.
1 Take off the overflow filter.
As indicated in the figure, nip the
elastic fixing claw and pull it to
the direction of the arrow to take
it off.(See to Figure 1)
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter ( as indicated in
Figure 2).
3. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
Elastic fixing
claw
Figure 1
Water level
adjusting lever
Corrugation
Pipe
Figure 2
4. Install the overflow filter.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the filter into
the valve cover.
(3).Hang up the hook at the left
upper side.
(4).Push the upper part in as
indicated in Figure 3.
Hook
Figure 3
13
Disposal after washing
Disposal of the complete unit
Wipe the complete unit with soft
cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
After washing, dismount the water inlet hose.
Do not store water in the tub for long period. Discharge the
water immediately after each wash.
Pull out the power plug and hang up the power cord.
Hang up the drain hose.
Wipe off the water drops on the surface and inside the tub with
clean soft cloth.
Open the cover of the wash tub and the inner/outer cover of the
spin tub for some time (about one hour), then close them.
Alcohol
Petrol
Thinner
14
Trouble-shooting Answer to questions
If the laundries fall to the outer side of the spin tubIf the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub,
If the laundries fall to the outer side of the spin tub,
please take them out immediately.
please take them out immediately.
1.Dismantle
1.Dismantle
As indicated in the figure, push the point marked
As indicated in the figure, push the point marked
with " " to pull the spin tub frame to oblique
with " " to pull the spin tub frame to oblique
upwards to dismantle it.
upwards to dismantle it.
2.Install
2.Install
After install the back edge of the spin tub frame to
After install the back edge of the spin tub frame to
proper position, push the four points marked with
proper position, push the four points marked with
" " by force to reset it.
" " by force to reset it.
Please check carefully. The laundries may fall to the
lower part of the outer side of the spin tub (as
indicated in the figure).
If the laundries fall to the outer side of the spin
tub, during spinning the draining will get blocked
and the rotation speed of the spin tub is reduced.
When the remaining water is frozen
Spin tubSpin tub
Spin tub frameSpin tub frame
LaundriesLaundries
Prevent the freezing (be sure to discharge the water completely
after using)
After complete draining, set the "WASH SELECTOR" at "STRONG"
or "STANDARD". If it is set at "DRAIN", it will be rather difficult for
the frozen water to melt.
When the water is frozen
Pour hot water below 50 into the
wash tub to soak it completely.
Then turn the pulsator on gently.
Please confirm the drainage can
work normally before using again.
Below 50 c
Below 50 c
2~3L
2~3L
15
Trouble-shooting Answer to questions
(If there's break down, please pull out the power plug before
checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair.
If there are real breakdowns, please call the after-sale service
department of our company. Do not repair it by yourself.
Phenomena The reason
The machine does
not act.
The draining does
not work
There's abnormal
sound during washing
There's abnormal
sound and violent
vibration during
spinning
There may be some
waterflowing out of
the drain hose in the
first use of the
machine.
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign
materials?
Is the drain hose frozen?
Is the drain hose blocked by foreign
material?
Are there laundries falling to the outer
side of the spin tub?
Are there hair pin, coins or metal items
brought inside the tub?
Is the machine slanting?
Is the gland pressed evenly?
Are there laundries falling to the outer
side of the spin tub?
Are the laundries in spin tub too much?
It is the water remaining from in the factory
inspection of performance.
16
Packing list
Name
User's manual
Warranty manual
Water inlet hose
Water-filling
jointer
Lint filter
Quantity
One piece
One piece
One piece
One piece
One piece
Gland
One piece
17
Specification
Water level/Water quantity (about)
Maximum/43L Medium/36L
Minimum/30L
Injection pressure(MPa)
Rated washing / spinning capacity(kg)
6.0/5.0 (weight of standard dry cloth)
0.02-0.2
Loading...