Haier WMQ-12.PX, WMQ-12.P User Manual

WASHING MACHINE

LAVE LINGE

MANUAL OF USE

MANUEL D’UTILISATION

France

WMQ-12.P

WMQ-12.PX

Contents

Names of the parts ………………………………………………1
Safety precautions……………………………………………2
Installation and adjustment……………………………………4
Preparation before washing……………………………………6
Put in the laundries……………………………………………7
Add the detergent
Close the top lid…………………………………………………

Select water level
Press the POWER button 8
Select program

Set of TEMPERATURE of wash and rinse water……………9

Press the START/PAUSE button…………………………………10
The washing is finished

After washing…………………………………………11
Trouble shooting answer to question…………………………12
Packing list………………………………………………………13
Specification………………………………………ĂĂĂĂĂ14

…………………………………………7

7

…………………………………………………8

………………………………………

…………………………………………………8

……………………………………10

Names of the parts

Program selector

Temperature Wash/Rinse switch

Top lid

Water level knob

Control panel

Control panel seat

Inner tub

Agitator

Cabinet

Start/Pause switch

Control foot of door switch

Power switch

Door switch

Bleach injection inlet

Meaning and description of the symbols

Warning sign

Contents marked with that symbol are related to the safety of the product
and the personal safety of the users. Please operate in strict conformity
to the contents, otherwise it may cause damage of the machine or injure
the personal safety of the user.

Cold water inlet valve

Hot water inlet valve

Water absorption cushion

Power line

Drain hose joint

Adjustable feet
(4)

Prohibition sign

Contents marked with that symbol are actions forbidden to perform.
Performing of those actions may result in damage of the machine
or injure the personal safety of the user.

1

Safety precautions

Please insert the power cord into special three

-phase receptacle.The earthing terminal of the
receptacle must be earthed reliably.If possible ,
please adopt electric leakage protector.

Earth

Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,please wipe
with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have
by the technicians of our special shop or the after-sale service department.

Do not put the machine at damp place like the bath
room. Never wash it with water.Not put wet laundries
on the control panel.

In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.

The power cord plug should be convenient
to be pluged in or pluged out with hand
while the washing machine runs normally.
Be sure to pull the plug out and close the
water tap when
moving the machine,or when cleaning
the machine.Do not use wet hand to ins­ert or pull out the power plug.

Do not use water hotter than 60℃.

the machine is idle,when

it replaced

C

60

Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.

Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal

vibrations in spinning.

2

Safety precautions

Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.

Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.

The handicapped or children

without

care shall not use the machine.

Do not decompose, repair or alter the
machine by yourself.

Do not wash laundries with volatile
materials (such as thinner, petrol etc.)

etrol

n

P

in er

h

T

Keep the machine away from direct
sunlight and heat source like the heater.

To prevent your laundries and washing
machine from damages, be sure to take
out all of the foreign materials from your
pocket, such as coins, buttons, sand or
hair pins etc.

In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.

Before washing, please check if the
water tap is open, and if the water inlet
pipe is connected properly.

It is suggested to use low-foaming
washing powder.

3

Installation and adjustment

Adjust the installation position

The largest allowed slope of the base of the machine is 2°. The slanting or rough
ground will result in unstable running or stoppage of the machine. Please adjust
it with following methods:

Confirm it's horizontal:

Hang the lead line to confirm
if it is horizontal.

Adjust the adjustable foot:

To twist the adjustable foot, please first lift up
the side of the foot slightly, and twist the foot.
.

Adjustable foot

<2

Install the drain hose

First install the drain hose hook on the parts of
outer drain hose component.

Put the drain hose clamp on the outer drain hose,
insert the outer drain hose into the joint for it, and

then clutch tightly with drain hose clamp.

Outer drain hose

Usage of the drain hose

The drainage shall be smooth with the drain hose.

1.put the drain hose up to suitable position.

2.Do not step on or press the drain hose.

High

component

Low

Drain hose hook

Drain hose clamp

Drain hose joint

1.0m-1.5m

4

Install the water inlet hose

1. Respectively attach the water inlet hoses to the hot water faucet and the cold
water faucet. ( As figure 1)

NOTE: Do not over tighten. Damage to the
valves can result.

2. Connect the hot and cold water inlet hoses to the hot and cold
water faucet.

Figure 1

3. Connect the other ends to their respective cold and hot water inlet valve
located at the rear of the washer

Jointer of the water inlet hose

C

Jointer of the
water inlet valve

H

Water absorption cushion

C

H

Figure 2

Note:

Hot water needs to be at a temperature of at least 120 F- 140 F.
(49 C-60 C)for the soap to dissolve and to avoid soap residue
remaining on clothes.

Check the connection between the water inlet
hose and the water tap

1.Swaying the hose gently to confirm if it is fastened
stable.

2.After installation, open the tap to check if it leaks.

3.Do not bend the hose with overstrain.

4.Before each usage please check if the connection
between the water inlet hose and the water tap, is firm,
so as to prevent dropping from improve Installation
position.

Tak e down the water inlet hose

1.Close the water tap.

2. Pull off the water inlet hose from the water tap and washer

5

Preparation before washing

Preparation before washing

1.Connect the water inlet hose. Open the water
faucet.

2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. The earth terminal shall not link to
gas pipeline and faucet water pipeline.

3.Put the drain hose up.

Pay attention to followings before washing the laundries

1.0m~1.5m

Confirm if
there's special
requirment for
the laundries.

a.Please check if the laundries are applicable for washing.
b.Separate those not colorfast from other laundries.
c.For laundries not water absorbing,please put them into water with hands.
d.For laundries with much soil,please remove the soil first.You can add detergent on the
part with serious soil directly.It is much easier to remove
e.For laundries likely to get lint ball or with long fiber,please first turn the inside out before
putting them into the water.
f.Do not put the laundries polluted with chemicals directly into the washing machine.

Clear the pocket.
Tak e out the
coins , sand,
hairpins etc.

Fasten the
buttons and
zippers.

The big laundries
like the jeans
shall be put in
loosely.

the soil by that mean.

When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
carefulness,please
put the laundries
with buttons into
other laundries.

6

Put in the laundries

Add the detergent

How to use the bleacher

Fill water to decided level .Dilute the whitener with
container. Pour it slowly into the washing tub.

Avoid using whitener on laundries with colour or
pattern as they are prone to lose colour.

The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and

quantity of the whitener.
For whitener powder, please dissolve it before use.

The capacity of washing and spinning of the machine
refer to the largest weight of the standard laundries
under dry condition that can be washed or spined in
one times. Washing quantity shall be lower than the
rated capacity.
The largest capacity of this machine is 10.0kg.

The thickness, size, type of the cloth will influence the
actual washing capacity. It is suitable for one time
washing to put in reasonable amount of laundries
and the laundries can be turned round in washing.

Do not select high water level for laundries small than

4.0kg, so as to avoid splashing of water.

How to use the washing powder

Direct dissolved in the machine(not applicable for fuzzy
and reserve programs)

1.Fill small quantity of water.

2.Add the power. Run for 30 seconds to dissolve
it completely.

3.Put in the laundries. Select suitable water level.
The instant dissolving of the washing powder:

1. Prepare warm water of 30℃ and a container.

2. Add the powder while stirring to fully dissolve it.
The powder is more prone to pollute the laundries than

the detergent. Therefore please use it with proper quantity.
It is suggested not to use high sudsing detergent.

Washing power with poor quality or not used for a long
period may get blocked. Please clean the detergent box
in time.

Close the top lid

If you open the top lid,
the machine will stop
working during spinning.

7

Select water level

Three water levels available according to the laundries quantity:

WATER LEVEL

MEDIUM

SMALL

LARGE

RESET

Press the POWER button

LARGE; MEDIUM; SMALL.

After the water inlet as per the preset water level, in case
additional water quantity is required, please first set the button
to the "RESET", and perform automatic water inlet. When it
reaches the suitable water level, you can turn it to the preset

level.

water

After the water inlet under set water level, if higher water level is
needed, please first turn the knob to " RESET ", then turn back to
needed water level. The washing machine will fill water to the
new water level automaticly .

WATER LEVEL KNOB

POWER Switch

POWER

Using this button to switch on or off the power. When the power is on ,
the relevant indicator light will be lighted.

When the washing is over , it will switch off the power automatically.

Select program

Circumvolve this knob, the following programs can be
selected solely:

STANDARD, HEAVY, GENTLE, QUICK, SPIN .

Mode and meaning of the indicator light

The frame of indicator is not lighted.
the frame of the indicator is flashing : indicate the running program.
the frame of the indicator is on : indicate the program about to run,
or indicate the selected mode.
the frame of the indicator is flashing rapidly: indicate abnormal condition.

Paraphrase of the program

Program the occasion

STANDARD The common washing.

HEAVY

GENTLE

QUICK

SPIN Only needing spining after washing with hands.

For washing bigger, thicker and heavily soiled laundry.

Washing woolen textile or underwear.

For quick washing of lightly soiled laundry.

STANDARD

HEAVY

CYCLE

GENTLE

QUICK

SPIN

SOAK

WASH

RINSE

SPIN

ON
OFF

8