Instruction and Installation Manual
60cm Fully Integrated Dishwasher
Model: UDW603
Your 1 Year Guarantee
Your appliance carries a 1 year parts and labour warranty. To fulfil the conditions of
your guarantee, the appliance must be correctly installed, operated in accordance with
the instructions and only be used for normal domestic purposes.
Please note that the guarantee and service availability only apply to the United Kingdom
mainland.
Customer Service
In case of difficulty please call the Customer Service Helpline number.
0844 800 7848
- When calling customer service, please ensure you have the model and serial number to
hand.
- Please keep your receipt or invoice in a safe place as they will be required as proof of
date of purchase.
Appliance 365 Limited, 730 Mandarin Court, Centre Park, Warrington, WA1 1GG
At time of delivery
• Check the packaging and dishwasher immediately for signs of transport damage. If the
appliance is damaged, do not put it into use but contact your supplier or customer
service department.
• Check you have received all the components required for the installation of this
appliance:
• 1 x instruction manual
• 2 x white plastic skids
• 1 x white plastic salt funnel
• 1 x anti-condensation strip
• 1 x drain hose U-bend clip
• 6 x short screws (shown above) for décor door bracket fitment
• 4 x long screws (shown above); 2 for use with the décor door fixing studs (fig
8) and 2 for securing the décor door from inside the dishwasher door frame
(fig 12).
• 4 x short black screws required for securing the appliance to the worktop or
adjacent cabinetry.
• Please dispose of packaging materials properly.
2 x décor
door lower
fixing
brackets
1 x rear foot
adjustment /
door balancing
tool
3 sets of
screws
2 x solid
worktop
fixing
brackets
2 x white plastic
décor door fixing
studs
2 x plastic
plugs (fig
12)
2 x sealed
plugs
1 x front foot
adjustment tool
Safety Information
During installation
Site the dishwasher and connect it up in accordance with the installation instructions.
The dishwasher must not be connected to the electricity supply whilst installation is
being carried out.
Ensure that the domestic wiring is properly earthed.
The mains electricity supply must conform to the details shown on the dishwasher
rating plate.
Do not connect the dishwasher to the electricity supply via an extension cable.
Built under appliances should always be installed under a continuous work surface
which is attached to adjacent cupboards, in order to ensure that the appliance is entirely
stable.
The mains plug must be easily accessible once the appliance has been installed.
The plastic housing on the water inlet contains an electrically operated valve. The
connecting wires are inside the inlet hose. Do not cut through this hose and do not
immerse the plastic housing in water.
During installation, the power supply cord must not be excessively or dangerously bent
or flattened.
During normal use
The dishwasher must only be used by adults for the washing of household dishes and
cooking utensils.
This appliance cannot be installed outdoors, not even if the area is covered by a roof. It
is also very dangerous to leave the appliance exposed to the rain and elements.
Do not place heavy objects on the door or stand on it when open. The appliance could
tip forwards.
The water inside the dishwasher is not suitable for drinking.
Do not use solvents of any kind inside the dishwasher. They could cause an explosion.
Open the door very carefully if the dishwasher is operating. There is a risk of water
squirting out.
Never touch the dishwasher when barefoot or with wet hands or feet.
The use of extension cords and multiple sockets is not recommended.
If the appliance is not operating correctly, or maintenance must be performed,
disconnect from the power supply.
If your family includes children
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience or knowledge unless they
have been given supervision or instruction concerning the use of this appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Keep detergents out of reach of children who must also be kept away from the
dishwasher when it is open.
If a fault occurs
If the appliance malfunctions, turn off the water supply to the appliance and disconnect
the plug from the wall socket.
Consult the section entitled “Troubleshooting” at the back of the manual.
If you cannot solve the problem, contact a service centre.
Only specialised engineers are authorised to make repairs.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
Only use original spare parts.
When disposing of old appliances
Installation
Positioning the appliance
Position the appliance in the desired location. The rear of the appliance should rest against
the wall behind it and the sides, along the adjacent cabinets or walls. The dishwasher is
equipped with water supply and drain hoses that can be positioned to the left or the right to
facilitate installation.
Anti-condensation strip
Fit the self adhesive anti-condensation strip (supplied) to the underside of the worktop
along the front edge (see Fig 16).
Levelling the appliance
The adjustable feet of the dishwasher allow it to be raised up to 870mm. If the space
between the floor and the underside of the worktop is greater than 870mm, the appliance
should be positioned on suitable wooden spacers which should always be fixed to the floor.
Use a spirit level to make sure the appliance is level front to back and left to right.
If the appliance is installed on a carpet, ensure there is a clearance beneath the appliance.
The four dishwasher feet should be adjusted to the correct height; the rear feet can be
adjusted using the tool supplied, via screws at the front of the appliance (fig 1a overleaf).
To increase the height, turn the screws in a clockwise direction, to lower turn in an anticlockwise direction. DO NOT use a power screwdriver to make this adjustment. The
dishwasher should not be inclined more than 2°. If the appliance is level, it will help to
ensure the dishwasher performs properly.
To prevent damage to the floor covering, the appliance must be installed using the plastic
skids provided.
Cold water connection
If the water pipes are new or have not been used for some time, let the water run to make
sure that the pipe is clear and free from impurities. Failing to do so may result in the water
inlet becoming blocked and the appliance may be damaged as a result.
Connect the water supply hose to a threaded ¾ connector, making sure that it is fastened
tightly in place (see Fig. 1).
Some models are fitted with an “aqua stop” water supply hose (see fig. 2) in which a small
filter is already housed in the threaded end.
Anti-flooding protection
The dishwasher is equipped with a system that stops the supply of water in the event of a
problem with the water supply hose or leaks within the unit, in order to prevent damage to
your home. If, for any reason, the box containing the electrical components happens to get
damaged, remove the appliance’s plug from the socket immediately. In order to guarantee
that the anti-flooding feature operates properly, the “A” box with water supply hose must be
Adjustable screw
attached to the water supply tap as shown in fig 2. No other type of connection is
acceptable. The water supply hose must not, under any circumstances, be cut as it
contains electrical parts which are live. If the hose length is not adequate to make a proper
connection, the hose must be replaced with one which is long enough. This hose is
available from specialised retailers and service centres.
Drain hose connection
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the
sink, making sure to avoid bending or crimping it. The free end of the hose must be at a
height between 40 and 100cm and must not be immersed in water (see Fig 3).
Electrical Connection
Check that the voltage and frequency values for the current in the home correspond to
those on the rating plate (located on the inner door of the appliance) and that the electrical
system is correct for the maximum voltage on the rating plate. Insert the plug into an
electrical socket which is properly earthed. The earthing of the appliance is a safety
requirement mandated by law. If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the whole cable rather than using
adaptors or similar as they could cause overheating and burns.
Electrical Connection (UK ONLY)
For your safety, please read the following information.
Warning: This appliance must be earthed.
This appliance must be connected to a 220-240 volts, 50Hz cycle AC supply by means of a
three pin socket, suitably earthed and should be protected by a 13 amp fuse.
This appliance is supplied with a rewireable 13 amp, 3-pin plug fitted with a 13-amp fuse.
Should the fuse require replacement, it must be replaced with a fuse rated at 13 amp and
approved to BS1362.
If the mains plug is unsuitable for the socket outlet in your home or is removed for any
other reason, then the plug should be disposed of safely to prevent the risk of electric
shock. Remove the fuse before disposal. There is a danger of electric shock if the cut off
plug is inserted into a 13-amp socket outlet.
Mounting the wooden door panel and locating the dishwasher in the cabinet
During the preparatory stages of installation, ensure that holes are not drilled into the sides
or the door of the appliance in order to avoid compromising the performance and / or
operation of the appliance.
Colour coding:
• The GREEN/YELLOW wire is the EARTH and
must be connected to the terminal which is
marked with the letter ‘E’ or ‘PE’, by the earth
symbol or coloured GREEN or
GREEN/YELLOW.
• The BLUE wire is the NEUTRAL and must be
connected to the terminal which is marked with
the letter ‘N’ or coloured BLACK.
• The BROWN wire is the LIVE wire and must be
connected to the terminal which is marked with
the letter ‘L’ or coloured RED.
The maximum dimensions and weight for the décor door are as follows:
Height: 725mm
Width: 598mm
Thickness: 20mm
Weight: 7kg
The following steps should be taken to fit the décor door:
Measure the width of the décor door
Align the top of the template (supplied) with the top of the rear side of the décor
door.
The left hand edge door should be aligned with the correct door width on the
template.
Mark the 4 fixing positions.
Repeat this process on the right hand side.
Remove the template and drill pilot holes in the décor door in all 8 positions using a
suitable drill and taking extra care not to drill through the door.
Attach the white plastic décor door fixing studs and lower fixing brackets as shown
in figure 8 below.
Offer the décor door up to the appliance door and slot the décor door fixing studs
into the appropriate slots on the dishwasher fascia panel.
Push the door up firmly until it stops.
Lower the décor door panel down slowly, applying pressure to the bottom of the
décor door to ensure it makes good contact with the appliance door. This will ensure
that the fins on the lower fixing brackets slide into their slots.
Do not release the décor door until you are certain the bottom of the door is secure.
Align the top of the décor door with adjacent cabinets.
Open the dishwasher door (the décor door should stay in place by itself).
Secure the décor door from inside the dishwasher using the screws provided (see
Fig 12 overleaf).
Cover the screw heads using the plastic plugs provided.
Insert the sealed plugs in the front crosspiece as shown in Fig 12a overleaf.
Loading...