Haier LD42U7000, LD50U7000 User Manual

LED LCD TV

OWNER' S MANUAL

MODEL: LD42U7000

LD50U7000

Please READ this manual carefully
before operating your TV, and retain
it for future reference

Contents

1. SAFETY AND WARNINGS .............................................................................................................2

2. INTRODUCTION ............................................................................................................................4

3. INSTALLATION ...............................................................................................................................5

4. REMOTE CONTROLLER ............................................................................................................. 11

5. TV OPERATION ........................................................................................................................... 12

6. TROUBLE SHOOTING ................................................................................................................23

-1-

IMPORTANT SAFETY INSTRUCTION

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, install in
accordance with the instructions.

8) Do not install near any heat sources such as
radiations, heat registers, stoves, or other apparatus

(including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized

plug. If the provided plug does not t into your outlet,

consult an electrician for replacement of the obsolete
outlet.

10) Protected the power cord from being walked on

or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.

11) Only use attachments/accessories specied by the

manufacturer.

12) Unplug this apparatus during lighting storms or

when unused for long periods of time.

13) Refer all servicing to qualied service personnel.

Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

14) Mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

15) The ventilation should not be impeded by covering

the ventilation openings with items, such as
newspapers, table-cloth, curtains, etc.

16) No naked ame sources, such as lighted candles,

should be placed on the apparatus.

17) Attention should be drawn to the environmental

aspects of battery disposal.

18) The use of apparatus in moderate climate.

19) The apparatus shall not be exposed to dripping

or splashing and that no objects lled with liquids,

such as vases, shall be placed on the apparatus.

Manufactured under license from Dolby Laboratories.
Dolby and the double D symbol are trademarks of
Dolby Laboratories.

SAFETY AND WARNINGS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN!

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The symbol indicates that dangerous
voltages constituting a risk of electric shock
are present within this unit.
The symbol indicates that there are
important operating and maintenance
instructions in the literaturaccompanying this
unit.

WARNING:

To reduce the risk of re or electric shock, do not

expose this apparatus to rain or moisture.

WARNING:
The batteries shall not be exposed to excessive heat

such as sunshine, re or the like.

This symbol indicates that this product incorporates
double insulation between hazardous mains voltage
and user accessible parts. When servicing use only
identical replacement parts.

This marking indicates that this product should not
be disposed with other household wastes throughout
the EU. To prevent possible harm to the environment
or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device,
please use the return and collection systems or contact
the retailer where the product was purchased. They
can take this product for environmental safe recycling.

CAUTION

-2-

SAFETY AND WARNINGS

High voltages are used in the operation of this television
receiver. Do not remove the cabinet back from your set.

Refer servicing to qualied service personnel.

To prevent re or electrical shock hazard, do not expose the

television receiver to rain or moisture.

Do not drop or push objects into the television cabinet slots
or openings. Never spill any kind of liquid on the television
receiver.

Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure of
electrical components.

Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it falls.

Do not place your television on an unstable cart, stand, shelf
or table. Serious injury to an individual , and damage to the
television, may result if it falls.

When the television receiver is not used for an extended

period of time, it is advisable to disconnect the AC power
cord from the AC outlet.

Avoid exposing the television receiver to direct sunlight and

other sources of heat. Do not stand the television receiver
directly on other products which give off heat, e.g. video

cassette players and audio ampliers. Do not place naked
ame sources, such as lighted candles on the television.

Minimum distances

10cm 10cm

20cm

5cm

Do not trap the power supply cord under the television
receiver.

Dim:515*320mm(不包括底座）

If the television is to be built into a compartment or similar
enclosure, the minimum distances must be maintained. Heat
build-up can reduce the service life of your television, and
can also be dangerous.

-3-

Main features

INTRODUCTION

1

Used as Television, display terminal, PC display;

2

High luminance, wide viewing angle;

3

Can store 200 TV programs;

4

HDMI interface;

5

Multi-Media player (USB);

Accessories

LED LCD TV.................................1 Power Cord......................................1

Bottom Stand..................................1 User Manual....................................1

Screw..............................................1

Remote Control..............................1 Quick Set Up Guide........................1

Battery(AAA).................................2

Warranty Card.................................1

(Only for India, Indonesia, Philippines)

E-waste Guideline Booklet.............1

(Only for India)

Main parameter

Model Name LD42U7000 LD50U7000
Resolution 1920 x 1080 1920 x 1080
Aspect Ratio 16:9 16:9

TV System

Video Signal System PAL/SECAM/NTSC PAL/SECAM/NTSC
Receiving Channel 1-200 1-200
Input Power Voltage AC 100-240V 50/60Hz AC 100-240V 50/60Hz
Power consumption 100W 120W
Audio Output

Power(THD≤7%)

Subwoofer 12W 12W

Signal Input

Horizontal denition (TV line)

Ambient Temperature 0 to 45 degree Celsius 0 to 45 degree Celsius

Wall mount

PAL/SECAM BG DK I , NTSC-M PAL/SECAM BG DK I , NTSC-M

2 x 8W 2 x 8W

Analog RGB(VGA) x 1

High-Denition Multimedia Interface

(HDMI) x 2
Composite Video Input x 2
Composite Video Output x 1
Audio Input x 1
YCb (Pb )Cr (Pr) x 1

Composite Video input >=350
Y Cb(Pb ) Cr(Pr) >=400

VESA mount pattern: 400 x 400mm
Screw: M6
Length: 16.5mm

This product does not include wall-mount braket module.

USB x 3
RF x 1
SD x 1
Coaxial x 1
Ethernet x 1

Composite Video input >=350
Y Cb(Pb ) Cr(Pr) >=400

VESA mount pattern: 400 x 200mm
Screw: M6
Length: 14.5mm

-4-

INSTALLATION

Front panel

3

1
2

3030

1. Remote control sensor.

2. Indicator LED: LED OFF POWER ON.

RED STANDBY.

3. Key board

KEYBOARD

SOURCE

MENU

VOL+

VOL-

CH

CH

POWER

1. SOURCE :
Display the input source menu.

2. MENU :
Display main MENU.

3. VOL+/ VOL- :
Adjust sound level.
In Menu mode, press "VOL+" or "VOL-" to adjust the
item that you selected.

4. CH / CH :
In TV mode, press CH or CH to change the
channel up and down.
In MENU mode, press CH or CH to select
items.

5. (POWER) :
Press this button to turn the unit ON from STANDBY
mode.
Press it again to turn the set back to STANDBY.

1

2

3

4

5

REAR AV Connections(SIDE)

All the terminals are (from up to down):
AV1 IN, USB, HDMI 1, SD/MMC, USB 3.0, AV OUT.

-5-

DOWN AV Connections

All the terminals are (from left to right):
LAN, COAXIAL, HDMI 2, RGB(PC), YPbPr/AV2 IN, ANT IN

Note: VIDEO, YPbPr and RGB(PC) all share one audio channel.

ANTENNA

Plug

INSTALLATION

Note:
Aerial connections: IEC (female).

Input impendance: 75Ω unbalanced.

ANT 75Ω

Adaptor (NOT SUPPLIED)

Loosen the screws

TWIN-LEAD FEEDER(300Ω)

Insert the feeder in Wires

An outdoor antenna

An outdoor antenna
CATV net

Tighten the screws

-6-

PC

STEPS:
Be sure both the TV and computer are Power off.

1. Connect VGA and audio cable.

2. Connect power cord.

3. Power on the TV switch to PC mode.

4. Power on the PC.

This sequence is very important.

INSTALLATION

8

Note: Appearance in the book is a schematic diagram, please buy the real.

-7-

INSTALLATION

PC Input Signal Reference Table

Connect a computer to your TV set and set up the computer output signal in accordance with table below.

Default computer mode

Item Resolution Horizontal Frequency (kHz) Vertical Frequency(Hz)

1 640 × 480 31.469 59.94

2 640 × 480 37.861 72.809

3

4 800 × 600 35.156 56.25

5 800 × 600 37.879 60.317

6 800 × 600 48.077 72.188

7 800 × 600 46.875 75

8 1024 × 768 48.363 60.004

9 1024 × 768 56.476 70

10 1024 × 768 60.023 75

11

12 1360 × 768 47.72 59.799

13 1440 × 900 59.887 60

14 1680 × 1050 64.7 60

15 1680 × 1050 65.3 60

16

640 × 480 37.5

1280 × 1024

1920 × 1080 67.5

63.981 60

75

60

DVI/ PC HDMI Input Signal Reference Table

When DVI port is being used: connect the DVI port of video device to your TV set with a DVI-to-HDMI line and set up
the output signal of the video device in accordance with table below.
When HDMI port is being used: connect the HDMI ports of your computer and TV set with one HDMI wire and set up
the output signal of the video device in accordance with table below.

Default computer mode

Item Resolution Horizontal Frequency (kHz) Vertical Frequency(Hz)

1 640 × 480 31.469 59.94

2 640 × 480 37.861 72.809

3 640 × 480 37.5 75

4 800 × 600 35.156 56.25

5 800 × 600 37.879 60.317

6 800 × 600 48.077 72.188

7 800 × 600 46.875 75

8 1024 × 768 48.363 60.004

9 1024 × 768 56.476 70

-8-

INSTALLATION

10 1024 × 768 60.023 75

11 1280 × 1024 63.981 60

12 1360 × 768 47.72 59.799

13 1440 × 900 59.887 60

14

15 1680 × 1050 65.3 60

16 1920 × 1080 67.5 60

1680 × 1050

64.7 60

Video Input Signal Reference Table

Connect the component signal or HDMI port of video device to your TV set and set up the output signal of the video
device in accordance with table below.
If your computer display card supports signals of video format then you can set up following output signal.

Default Component or HDMI Mode

Standard Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz)

SD 640 × 480p

SD 720 × 480i 15.734 60

SD 720 × 480p 31.5 60

SD 720 × 576i 15.625 50

SD 720 × 576p 31.25 50

HD 1280 × 720p 37.5 50

HD

HD 1920 × 1080i 28.125 50

HD 1920 × 1080i 33.75 60

FHD 1920 × 1080p 56.25 50

FHD 1920 × 1080p 67.5 60

1280 × 720p 45

25.175

60

60

Video Input Signal Reference Table

Video System Supported in TV and Video Modes
PAL/SECAM/NTSC

Standard Denition Interface

You can also enjoy traditional program by using a DVD player or VCR Player. Connect this equipment to your TV via
the Composite Input on the back of your TV.

-9-

INSTALLATION

AV EQUIPMENT

This TV provides two group of AV, one group of YPbPr for convenient connection to VCR, DVD or other video
equipment. Please refer to the owner's manual of the equipment to be connected as well.
You can use the input terminals on TV set rear as follows.

TO AUDIO OUTPUTS

TO VIDEO OUTPUTS

HDMI

VIDEO EQUIPMENT

VIDEO EQUIPMENT with YPbPr

R

W

GBR

R

Red (audio R)

W

White (audio L)

R

Red (Pr or Cr)

Blue (Pb or Cb)

B

G

Green (Y)

R

NETWORK

W R

B

G

It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder, video game or stereo
system, etc...
YPbPr can support these video fomats: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p.
Note:

1. AV and YPbPr share one audio channel.

2. When HDMI port get DVI signal, the "PC Audio" channel is changed to receive the audio for HDMI port.

3. Sometimes it will not support in different device because the device supplys nonstandard signal.

4. When current source is TV, VIDEO OUT signal is TV; when current source is AV, VIDEO OUT signal is AV;
othersources have no VIDEO OUT signal.

5. TV system supports HDMI CEC feature which involves One Touch Play, Auto Standby and Audio Return Channel
(ARC).

-10-

The remote control cannot be operated unless the batteries are properly loaded inserted.
When using the remote control, aim it at the remote control sensor on the TV.

Function introduction

Press to adjust the volume level.

1

2
3

4

5

6

7

8
9

10
11

12

13

14
15

16

17

18

1. (POWER)

Press to turn the TV on or off .

2. S.MODE

Press to select the sound mode.

3. P.MODE

Press to select the picture mode.

4. 0-9

Press to enter a channel number or password.

5. FREEZE

Press to freeze the picture.

6. Mute

Press to turn the sound on or off.

7. +/-

OK

HTR-A18H

19

20

21

22

23

24

25

26

27

28

29
30

31

32

8. 3D

Press to turn on 3D mode setting menu.

9. FAV/

Press to open FAV channel list.

10. MENU/

Press to open on-screen Main Menu.

11. CC/

No used.

12. PAGE+

Press to go to the rst item APK in all APK list (in

SmartTV launcher).

13.

a. Press to navigate OSD menu.
b. Press to change setting value in options items.

14. PAGE-

Press to go to the last item APK in all APK list (in
SmartTV launcher).

15. (reverse)

Press to rewind playback in multi-media mode.

16. (play/pause)

Press to play/pause playback in multi-media mode.

17. P. SIZE

Press to change the screen display aspect ratio
setting.

18.SLEEP

Press to set sleep timer.

19. SOURCE

Press to open Input Source list.

20.

Press to open (SmartTV) launcher mode.

21. Q. VIEW

Press to switch to the last viewed channel.

22. CH

Press to change the channel.

23. CH.LIST

Press to open the channel list.

24. I/II/MTS/SAP

Press to select the audio mode (depend on broadcast
signal).

25. INFO/

Press to display the channel information.

26. BACK/

Press to return to the previous menu.

27. OK

Press to comrm a selection.

28. EXIT/

Press to return to the previous menu.

29. (forward)

-11-

REMOTE CONTROLLER

TV OPERATION

Press to fast forward playback in multi-media mode.

30. (stop)

Press to stop playback in multi-media mode.

31. (Sub-MENU)

Support" pop-up message would be displayed on
screen.

32. (H.LOCK)

No used.
Press to open/close APK option menu list (it APK
support this feature); for general TV source, "No

Video Setup

Video

Video

Audio

TV

Setting

Picture Mode

Backlight

Brightness

Contrast

Saturation

Hue

User

100

50

50

50

50

Items Description

Picture Mode Select picture mode User, Vivid, Natural, Sports, Lightness, Standard, Soft.

Backlight Control the brightness of the backlight.

Brightness To brighten the dark parts of the picture.

Contrast To sharpen the picture quality.

Saturation Press key to decrease or increase saturation.

Hue Compensates colour variations in NTSC encoded transmissions.

Sharpness To improve details.

Color Temperature Selet the color temperature mode Standard, Warm, Cool.

Advanced Video

Dynamic Backlight

Dynamic Contrast

Dynamically adjusts backlight level based on average brightness of the
picture frame.
Dynamically enhance the details in the dack, medium and light areas of
the picture.

Aspect Ratio Select the picture ratio to suit the video source (4:3, 16:9, Full Screen, Zoom1 and Zoom2)..

The 3D watching effect can be obtained only if the TV source is in 3D mode ( 3D display
feature is only available in HDMI sources and video playback in MyFun ) and you wear a pair
of 3D glasses.

Press the General Functions Menu to nd the 3D option or press the 3D shortcut key on the
remote control to enter the 3D congurationi interface directly; the options are as follows:

3D

1. 3D Mode: Select 3D mode Off, Auto, SBS, TB, 2D-to-3D.

2. 3D to 2D: Provide ON and OFF setup. Convert 3D picture into 2D display.

3. Depth: Adjust the overall 3D depth of eld and hierarchical sense of the picture on the
screen.

4. LR Switch: Provide ON and OFF setup. When the left and right views of a picture are
displayed contrarily, exchange the positions of the left and right views.

5. 3D offset. (Available for 2D-to-3D mode only).

VGA Setting Select to set VGA. Only for VGA source. Please see page 15 .

NR Select the amount of noise reduction for the picture (Off, Low, Medium and Strong).

Video\Sharpness

Video

Audio

TV

Setting

-12-

Sharpness

Color Temperature

Advanced Video

Aspect Ratio

3D

VGA Setting

50

Cool

16:9

Audio Setup

TV OPERATION

Audio

Video

Audio

TV

Setting

Sound Mode User

Digital Surround

EQ

SPDIF

AVL

Balance

PCM

Off

Off

50

Audio/Audio Only

Video

Audio

TV

Setting

Audio Only

Items Description

Sound Mode Select sound mode User, Standard, Music, Movie, News.

Digital Surround

Create vivid and connotation-rich surround sound experience through speakers. Provide ON
and OFF setup.
Adjust the volume of the left and right speakers.

EQ

120Hz, 500Hz, 1.5KHz, 5KHz, 10KHz: Adjust the frequency so that the sound quality is
adapted to your favorite. When pre-enhancing the bass, increase the low frequency; when pre­enhancing the treble, increase the high frequency.

SPDIF Select digital audio output options: PCM or RAW( availabel for HDMI).

AVL

Automatically reduces sudden volume changes,for example,when switching between the
channels.

Balance Adjust the balance between left and right speakers to adapt to your listening position.

Audio Only Select to turn off the panel screen and keep only the sound on.

-13-

TV Setup

This setup is available in ATV mode only.

TV

Video

Audio

TV

Setting

Auto Scan

Channel Edit

TV OPERATION

Items Description

TV automatically searches for the channel in the available frequency band and stores
sequentially.

Auto Scan

Select

TV

menu.
Select Auto Scan and press OK key to tune channels automatically and store.
During auto searching Press BACK/ key to stop search.

Channel Edit

Edit the selected channel, including Move Delete, Favorite, Edit, Channel Name, Color System,
Sound System, Search.

Note: Make sure you have connected RF signal cable before performing channel search.

Features Setup

Setting

Video

Audio

TV

Setting

Items Description

Advanced Setting

Blue Screen

Scheduled Time Set a scheduled time to power on the TV when TV is in Standby mode.

Sleep Time

Logo Light

Advanced Setting

Blue Screen

Scheduled Time

Sleep Time

Logo Light

Reset Default

Off

Off

Off

Access advanced settings.
Press OK key to select Application Manager, Network, Location/City, Input method
editor, Date and Time, System and Wireless Display.

To show Blue or Black screen when no signal input in non-ATV sources.
Select Off: Black screen display when no signal input.
Select On: Blue screen display when no signal input.

Set a time period after which the TV will be turned off and enter stand by mode.
Sleep timer can be set to Off,10, 20, 30, 60, 90,120, 180 or 240 Minutes

Select to light up the LED of Haier logo or not.
Select off: Turn off the LED light of Haier logo.
Select on: Turn on the LED light of Haier logo.

-14-

TV OPERATION

Reset Default

The channel installation settings remain the same.
This TV does not support child lock function.

Channel edit description

You can restore the factory default video and audio settings of your TV.

1. Select TV Menu

2. Select Channel Edit and press OK key to get into Sub-Menu

3. Press Blue key [Edit] to get into Sub-Menu

4. Select Search and press key to manual scan previous/next available Channel.

5. Press Back or Exit key to exit manual search scan and back to previous menu.

TV\Channel Edit\Channel Name

Video

Audio

TV

Setting

Channel Name

Color System

Sound System

Search

S-07

PAL

DK

Freq.

Computer Setup

This setup function is available in VGA mode.

Video\VGA Setting

Video

Audio

TV

Setting

Sharpness

Color Temperature

Advanced Video

Aspect Ratio

3D

VGA Setting

Cool

16:9

50

Video\VGA Setting\Auto

Video

Audio

TV

Setting

Auto

Horizontal

Vertical

Phase

Clock

50

50

50

50

Items Decsription

Auto Press OK key to adjust the screen automatically to the optimal position of the picture.

Horizontal Adjusts the horizontal position of the picture.

Vertical Adjusts the vertical position of the picture.

Phase Eliminate the horizontal interfering lines.

Clock Eliminate the vertical interfering lines.

Note:
If the PC is connected to the TV and no signal has been input from the PC for more than 30 seconds,the TV enters
the standby mode automatically.

-15-

TV OPERATION

3D Setup

Entering into 3D setup

1. Pressing 3D key on remote when OSD Menu is unavailable.

2. Press the Menu key select Video Menu by pressing / key and press OK key to select 3D.

Video\3D\3D Mode

Video

Audio

TV

Setting

3D Mode

3D to 2D

Depth

LR Switch

3D Offset

SBS

Off

15

Off

30

3D setup description

3D mode
To get proper 3D effect in correct 3D video display. TV provides 3D modes as Off, Auto, SBS (Side-By-Side), TB
(Top-to-Bottom) and 2D-to-3D. 3D display feature is only available in HDMI sources and video playback in MyFun.

Smart TV

1. Connect your TV to ethernet. Parts of TV function will not work without network.

2. Press key on remote control to enter smart TV screen.

Screen description:

TV:
TV picture being broadcast.

Applications:
The basic shortcut function in
the Android system.

Weather:
Synchronously view the
weather status.

User Apps:
Display the Android
applications downloaded
via network or installed via
an external storage device
(Ex:USB) by the user in a
shortcut manner.

-16-

TV OPERATION

Network connection

Wired network connection

This machine supports network function, be sure to correctly connect the network rst.

The following are two network connection modes, and you can select the most suitable connection mode according
to the actual situation.

Connect to a wired routher, so as to connect to the Internet via a wall mounted LAN port.

Wall mounted LAN port

Router

LAN cable

Wireless network connection

Connect to the Internet via a
wireless router.
* This machine has a wireless
network adapter built in, so no
externally connected adapter is
needed.
For the setup of the wireless
router, please refer to the wireless
router operation instructions.

* The issues related to stability, connectivity and etc., may cause the system not to operate normally.
Although this occurs rarely, it is normal phenomenon.
Please try to turn off the power and restart so that the system is initialized to resume to normal operation.

Wall mounted LAN port

Wireless router

LAN cable

-17-

TV OPERATION

Network Setting

Select the desired network connection mode and correctly set up the parameters.
Press key to enter smart TVand use key to select Setting Menu, then press OK.
Press key to select Network, then press OK.
Press key to select Ethernet setting or Wireless, then press OK.

Ethernet setting

If LAN cable is connected and DHCP (automatically set up) is supported, the Internet Protocol (IP) setting will be

automatically congured.

If you want to manually set up the IP, operate according to the following steps:

1. Press the OK key to select connection so as to automatically obtain an IP address [OFF].

2. Press the keys to select the elds to be changed, and directly enter corresponding parameters, i.e., [IP

address], [subnet mask], [default gateway], [rst DNS], and [second DNS], by pressing the number keys.

3. Press the keys to select [Save], and press the OK key to complete the IP address setup.

Network Ethernet settings

Status

Ethernet setting

Wireless

Proxy setting

Wi-Fi Direct

Wi-Fi Hotspot

Open ethernet

The automatic acquisition IP address

IP address

subnet mask

default geteway

first DNS

second DNS

Save Cancel

0 0 0 0

255 255 255 255

0 0 0 0

0 0 0 0

0 0 0 0

Choice BackComfirm

On

On

Wireless setting

The system will automatically search for available wireless network access points; press the OK key to enter into the
submenu, set Wi-Fi to [On], press the keys to select an access point you want to connect, and press the OK
key to connect.

If you select an access point with security certication, a password entering interface will appear after you conrms.

Network Wireless

Status

Ethernet setting

Wireless

Proxy setting

Wi-Fi Direct

Wi-Fi Hotspot

Wi-Fi

TFW

CMCC-AUTO

TP_Test

CNCC

CMCC-AUTO

CMCC-AUTO

connect

Choice BackComfirm

On

-18-

local disk device

MyFun

TV OPERATION

Multimedia Center

TV USB port and SD/MMC port can be used to view JPEG photos, play mp3 music and Video les in USB devices.

Entering to USB Media

1. Press key on remote to enter home page.

2. Press key to select Myfun icon to enter multimedia menu as shown above

3. Select the Media type (All/Picture/Music/Video) to be viewed and press OK key to enter into USB Media and
When USB drive is detected by the TV, USB drive is displayed as a folder on the screen as shown below.

4. Press OK key to view subfolder or les in the USB driver.

5. Press

Back

Exit

or

key to exit MyFun apk.

ALL

back

my heart will go on.aac

take me to your heart.aac

3D_Mpeg2_1920x1080_AC.mkv

ALL

thumb.db

aac

aac

mkv 928MB3D 1280x1080_side by side.mkv

aac 3MB

db 6KB

foldermy document

foldermy favorit

3MB

3MB

CHRIS

BROAM

DEIBS

AFGS

AFGS

MISBCDH

1/1

Note: * Files of selected Media type can only be viewed through USB. Media type can be any one amoung Picture/
Music/Video.

Viewing Photos

1. Thumbnail of the available images will be displayed on the screen. If no images are displayed then select the
folder containing the Photos.

2. When a photo is displaying, press OK or navigation key to show infomation bar which lists photo information and
help bar.

3. Once information bar displays on bottom, press key to start photo slideshow.

Multimedia settings for Photo Slide show

picture is 001041567.jpg 1920x1080 677KB Start/Stop slide show Zoom inOK

-19-

TV OPERATION

Press OK key to get following Menu setup shown above.

1. [Play/Pause]: Play/Pause photo play.

2. [Zoom in]: Zoom in the Photo with scale factor (1×/2×/4×/8×).

Playing Music les

1. Thumbnail of the available music les will be displayed on the screen. If no les are displayed then select the
oder containing the music les.

2. To play particular music le select the required le and press OK key.

3. Press key to play/pause music. Select and click or button on OSD to play previous or next track. (

or key on remote control are not available in music playback mode.)

Multimedia settings for Music play

Wherver You Will Go

Camino Palmero

The Calling

00:43/03:22

Following Menu setup shown above.

1. / ( Play/Pause ): Play/Pause music play.

2. ( Repeat ): Select the repeat mode as Random, Repeat One, Repeat All.

3. / ( Previous/Next ): Jump to previous or next music play.

Playing Video les

1. Thumbnail of the available video les will be displayed on the screen. If no les are displayed then select the
folder containing the video les.

2. To play particular video le select the required le and press OK key.

3. Press key to play/pause video.

Multimedia settings for Video play

1x

Following Menu setup shown above.

1. / ( Play/Pause ): Play/Pause movie play.

2. / ( Rewind/Fast Forward ): Rewind/Fast Forward video play.

3. ( Repeat ): Select the repeat mode as Repeat One, Repeat All.

4. ( Settings ) : Enter the settings of Menu.

-20-

00:00:14/00:03:26 [MV] GangnamStyle

Files encoded in the following formats are supported.

Picture

Image Ext. lename Photo Format Suggest Resolution Max Width Max Height

JPEG .jpg, .jpeg Base-line 15360×8704 15360 8640

Progressive 1024×768 1024 768

PNG .png Non-interlace 9600×6400 9600 6400

Interlace 1200×800

1200 800

BMP .bmp 9600×6400 9600 6400

Audio

Audio Codec File extension Bit Rate Remark

MPEG1/2 Layer1 MP3 32Kbps ~ 448Kbps (Bit rate)

16KHz ~ 48KHz (Sampling rate)

MPEG1/2 Layer2 MP3 8Kbps ~ 384Kbps (Bit rate)

16KHz ~ 48KHz (Sampling rate)

MPEG1/2 Layer3 MP3 8Kbps ~ 320Kbps (Bit rate)

16KHz ~ 48KHz (Sampling rate)

AC3 N/A (work with vide les

only)

32Kbps ~ 640Kbps (Bit rate)

32KHz ~ 44.1KHz, 48KHz (Sampling

rate)

EAC3 N/A (work with vide les

only)

32Kbps ~ 6Mbps (Bit rate)

32KHz ~ 44.1KHz, 48KHz (Sampling

rate)

AAC-LC M4A/AAC Free Format (Bit rate)

For Miracast feature only

8KHz ~ 48KHz (Sampling rate)

WMA WMA 128 bps ~ 320Kbps (Bit rate)

8KHz ~ 48KHz (Sampling rate)

Follow WMA 7, WMA 8, WMA 9
Standard

Video

File extension Container Video Codec

dat, mpg, mpeg MPG, MPEG MPEG1,2

ts, trp, tp, m2ts TS MPEG2, AC1, AVS

vob MPEG2-PS MPEG2

mp4, mov MP4 MPEG1,2,4, Xvid, VC1, Motion JPEG

rm, rmvb RMVB,RM Rv30, rv40

.mkv MKV MPEG 1,2,4, Xvid, VC1, Motion JPEG

.avi AV I MPEG1,2,4 Xvid, VC1, Motion JPEG

.asf, .wmv ASF MPEG2,4 Xvid, VC1

Remarks:

1. USB interface of digital multimedia player is not all-purpose. So when some USB devices could not be
recognized, the problem is usually not the performance failure but due to device driver.

2. Because USB devices and memory capability are different, the time needs for multimedia player to read
information are also different. So the information reading speed of the player temporarily getting slow are not the
performance failure.

3. The voltage supplied to USB interface is 5V, and the most electrical current is 500mA. When some interface
criteria of USB devices are different from standard USB protocol, digital multimedia player may be unable to
recognize USB devices correctly, which is normal status.

4. USB could be used as an interface to update software.

-21-

5. If some les source could not play because of the parameter decoding-limitation, the problem is not performance
failure.

6. The system only applies to memory medium with FAT32 format.

7. Does not support connecting of removable devices to the USB hub.

8. The USB device does not support copying and pasting for FAT32 system.

9. The system doesn't support USB devices which possibly need larger power consumption, ex: USB hard-drive
device or certain media playback device.

10. USB 3.0 port supports USB 3.0 and USB 2.0 devices, but doesn't support USB 1.1 device. USB 2.0 port supports
USB 2.0 and USB 1.1 devices, but doesn't support USB3.0 device.

* Haier is not responsible for any quality problems or data loss of the external digital storage devices.

-22-

TROUBLE SHOOTING

Trouble phenomenon

Inspection

Picture Audio

Snow Noise antenna position, direction or connection

Ghost Normal audio antenna position, direction or connection

Interfere

Normal Picture Mute

No picture Mute

No color Normal audio color control

Noise

electronic equipment, car/motorcycle,

uorescent light

Volume (inspect wether the mute function
on the remote control are started, or audio
system are correct or not)

Power cord is not inserted
Power switch is not opened
Contrast and brightness/volume setup
Press standby key on the remote control
for inspecting

Scramble Normal audio or weak retune channel

No color Noise Audio system

-23-

X41G42MV67217A