LCD TV
OWNER' S MANUAL
MODEL: L19 M3
L22M3
L24M3
Please READ this manual carefully
before operating your TV, and retain
it for future reference
Contents
1 Safety and warnings..........................................................................................................2-3
2 Introduction.....................................................................................................................4
3 Installation...................................................................................................................... 5-11
4 Remote Controller........................................................................................................... 12
5
TV Operation..................................................................................................................13-15
Trouble shooting............................................................................................................. 16
6
-1-
IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, install
in accordance with the instructions.
8) Do not install near any heat sources such as
radiations, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the
polarized plug. If the provided plug does not fit
into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protected the power cord from being walked
on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified
by the manufacturer.
12) Unplug this apparatus during lighting
storms or when unused for long periods of time.
13) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
14) Mains plug is used as the disconnect device,
the disconnect device shall remain readily
operable.
15) The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloth, curtains, etc.
16) No naked flame sources, such as lighted
candles, should be placed on the apparatus.
17) Attention should be drawn to the
environmental aspects of battery disposal.
18) The use of apparatus in moderate climate.
19) The apparatus shall not be exposed to
dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on
the apparatus.
SAFETY AND WARNINGS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The symbol indicates that dangerous
voltages constituting a risk of electric shock
are present within this unit.
The symbol indicates that there are
important operating and maintenance
instructions in the literaturaccompanying this
unit.
WARNING:
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
WARNING:
The batteries shall not be exposed to
excessive heat such as sunshine, fire or the
like.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user accessible
parts. When servicing use only
identical replacement parts.
This marking indicates that this product should
not be disposed with other household wastes
throughout the EU. To prevent possible harm to
the environment or human health from
uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of
material resources. To return your used device,
please use the return and collection systems or
contact the retailer where the product was
purchased. They can take this product for
environmental safe recycling.
CAUTION
-2-
High voltages are used in the operation of this television
receiver. Do not remove the cabinet back from your set.
Refer servicing to qualified service personnel.
SAFETY AND WARNINGS
Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it falls.
To prevent fire or electrical shock hazard, do not expose
the television receiver to rain or moisture.
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure of
electrical components.
Do not place your television on an unstable cart, stand,
shelf or table. Serious injury to an individual , and damage
to the television, may result if it falls.
When the television receiver is not used for an
extended period of time, it is advisable to disconnect
the AC power cord from the AC outlet.
Avoid exposing the television receiver to direct sunlight
and other sources of heat. Do not stand the television
receiver directly on other products which give off heat,
e.g. video cassette players and audio amplifiers. Do not
place naked flame sources, such as lighted candles on
the television.
Do not trap the power supply cord under the television
receiver.
If the television is to be built into a compartment or similar
enclosure, the minimum distances must be maintained. Heat
build-up can reduce the service life of your television, and
can also be dangerous.
-3-
Dim:515*320mm(
INTRODUCTION
Main features
Used as Television, display terminal, PC display
High luminance, wide viewing angle
Can store 100 TV programs
HDMI interface
Multi-Media player (USB);
Main parameter
Viewing Picture Size (Diagonal)
Resolution
Aspect Ratio
TV System
Video Signal System
Receiving Channel
Input Power Voltage
Power consumption
Audio Output Power
Signal Input
Horizon
tal definition TV line
THD 7%
18.5 inch
1366x768
16 : 9
PAL/BG
PAL/NTSC/SECAM
1-100
AC 100-240V~50/60Hz
30W
2 x 3W
Analog RGB(VGA) x 1
High-Definition Multimedia Interface (HDMI) x 2
Composite Video Input x 2
Composite Video output x 1
Audio Input x 3
YCb (Pb )Cr (P R) x 1
USB x 1
RF x 1
Composite Video input >=350
Y Cb(Pb ) Cr(Pr ) >=400
Accessories
Infrared Remote Controller............
Battery(AAA)...............................2
User s M anual...............................1
AV2 IN/AV OUT cord....................1
21.6 inch
1366x768
16 : 9
PAL/BG
PAL/NTSC/SECAM
1-100
AC 100-240V~50/60Hz
60W
2 x 3W
23.6 inch
1920x1080
16 : 9
PAL/BG
PAL/NTSC/SECAM
1-100
AC 100-240V~50/60Hz
60W
2 x 3W
1
-4-
Front panel (L19M3)
30 30
Front panel (L22M3/L24M3)
30 30
INSTALLATION
3
1
2
4
3
1
2
4
1: Remote control sensor.
2: Indicator LED: GREEN POWER ON.
RED STANDBY.
3: Side buttons
4: Power button: Press the Power Button to
turn the unit on or off.
1: Remote control sensor.
2: Indicator LED: GREEN POWER ON.
RED STANDBY.
3: Side buttons
4: Power button: Press the Power Button to
turn the unit on or off.
KEYBOARD (L19M3/L22M3/L24M3)
1 SOURCE:
Display the input source menu.
2 MENU:
Display main MENU.
SOURCE
MENU
CH+
CH-
VOL+
VOL-
STANDBY
USB
3 CH+/CH-
In TV mode, press "CH+" or "CH-" to change the channel up and down.
In MENU mode, press "CH+" or "CH-" to select items.
In standby mode, press "CH+" or "CH-" to turn on the TV.
4 VOL+/VOL-
Adjust sound level.
In MENU mode, press "VOL+" or "VOL-" to adjust the item that you selected.
5. STANDBY
Press this button to turn the unit ON from STANDBY mode.
Press it again to turn the set back to STANDBY.
6. USB
The USB memory stick should be plug in the unit directly. USB extension cable
should not be used to avoid failing of data transferring and interference caused.
-5-
REAR AV PASTER (L19M3)
INSTALLATION
AC-INPUT
100-240V~ 50/60Hz
RF INPUT
AV2 IN/AV OUT
PC
AUDIO INPUT
VGA INPUT
HDMI1 INPUT HDMI2 INPUT
All the terminals are (from left to right):
AC POWER SOCKET, ANTENNA, AV2 IN/AV OUT, PC AUDIO INPUT, VGA , AUDIO INPUT,
YPbPr, AV INPUT, HDMI 1, HDMI 2, POWER SWITCH.
Note: 1.AV and YPbPr share one audio channel.
2.When HDMI 1 port get DVI signal, the "PC Audio" channel is changed to receive the audio
for HDMI 1 port.
REAR AV PASTER (L22M3)
HDMI1 INPUT
AC-INPUT
100-240V~ 50/60Hz
All the terminals are (from left to right):
AC POWER SOCKET, HDMI 1, HDMI 2, AV, YPbPr, AUDIO INPUT, VGA , PC AUDIO INPUT,
AV2 IN/AV OUT, ANTENNA.
Note: 1.AV and YPbPr share one audio channel.
2.When HDMI 1 port get DVI signal, the "PC Audio" channel is changed to receive the audio
for HDMI 1 port.
HDMI2 INPUT
AVPrY
L
Pb
R
AUDIO INPUT
PC
AV2 IN/AV OUT
RF INPUT
REAR AV PASTER (L24M3)
Pb
HDMI1 INPUT HDMI2 INPUT
All the terminals are (from left to right):
AC POWER SOCKET, HDMI 1, HDMI 2, AV, YPbPr, AUDIO INPUT, VGA , PC AUDIO INPUT,
AV2 IN/AV OUT, ANTENNA.
Note: 1.AV and YPbPr share one audio channel.
2.When HDMI 1 port get DVI signal, the "PC Audio" channel is changed to receive the audio
for HDMI 1 port.
L
RAVPrY
AUDIO INPUT
PC
AV2 IN/AV OUT
RF INPUT
-6-
ANTENNA
INSTALLATION
Note:
Aerial connections:IEC(female).
Input impendance:75 unbalanced.
PC
STEPS:
Be sure both the TV and computer are Power off.
1.Connect VGA and audio cable
2.Connect power cord
3.Power on the TV, switch to PC mode
4.Power on the PC
This sequence is very important.
(L19M3)
VGA INPUT
PC
AV2 IN/AV OUT
RF INPUT
AC-INPUT
100-240V~ 50/60Hz
AUDIO INPUT
8
HDMI1 INPUT HDMI2 INPUT
-7-
(L22M3)
HDMI1 INPUT HDMI2 INPUT
AC-INPUT
100-240V~ 50/60Hz
(L24M3)
HDMI1 INPUT HDMI2 INPUT
PRESET MODE (PC)
1
2
3
4
5
NOTE: PC V.Freq.(Hz) not more than 60Hz.
RESOLUTION
800*600
1024*768
1360*768
(Only for 19", 22")
1280*768
(Only for 24")
1920*1080
(Only for 24")
AVPrY
INSTALLATION
8
L
Pb
R
Pb
L
RAVPrY
PC
AV2 IN/AV OUT
RF INPUT
AUDIO INPUT
PC
AV2 IN/AV OUT
RF INPUT
AUDIO INPUT
V.Freq.(Hz) H.Freq.(KHz)
60
60
60
60
60
8
37.88
48.36
47.7
47.3
67.5
PRESET MODE (HDMI)
1
2
3
4
5
RESOLUTION
800*600
1024*768
1360*768
1280*768
1920*1080
V.Freq.(Hz) H.Freq.(KHz)
60
60
60
60
60
37.88
48.36
47.7
47.3
67.5
-8-
INSTALLATION
AV EQUIPMENT (L19M3)
This TV provides two groups of AV, one group of YPbPr for convenient connection to VCR, DVD or other
video equipment. Please refer to the owner's manual of the equipment to be connected as well.
You can use the input terminals on TV set rear as follows.
VIDEO EQUIPMENT with YPbPr
W
R
HDMI1 INPUT HDMI2 INPUT
Y
Yellow (video)
R
Red (audio R)
W
White(audio L)
R
Red(Pr or Cr)
B
Blue(Pb or Cb)
G
Green(Y)
HDMI
AC-INPUT
100-240V~ 50/60Hz
GBR
W
R
G B R
VGA INPUT
PC
AV2 IN/AV OUT
RF INPUT
AV2 IN
R
W
AUDIO INPUT
W
R
Y
To audio
R
WY
with
terminal
VIDEO EQUIPMENT
outputs
AV OUT
To video
R
W
Y
Y
output
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder, video game
or stereo system, etc.....
YPbPr can support these video fomats: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p.
Note: 1.AV and YPbPr share one audio channel.
2.When HDMI 1 port get DVI signal, the "PC Audio" channel is changed to receive the audio for
HDMI1 port.
3.Sometimes it will not support in different device because the device supplys nonstandard signal.
4.When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT signal is
AV; other sources have no AV OUT signal.
-9-
INSTALLATION
AV EQUIPMENT (L22M3)
This TV provides two groups of AV, one group of YPbPr for convenient connection to VCR, DVD or other
video equipment. Please refer to the owner's manual of the equipment to be connected as well.
You can use the input terminals on TV set rear as follows.
VIDEO EQUIPMENT with YPbPr
W
R
PC
AV2 IN/AV OUT
AUDIO INPUT
W
RF INPUT
R
W
Y
AV OUT
Y
Y
Yellow (video)
R
Red (audio R)
W
White(audio L)
R
Red(Pr or Cr)
B
Blue(Pb or Cb)
G
Green(Y)
HDMI
AC-INPUT
100-240V~ 50/60Hz
HDMI1 INPUT
VIDEO EQUIPMENT
with
terminal
HDMI2 INPUT
AVPrY
Y
G B R
RWY
Pb
To audio
outputs
To video
output
GBR
W
R
L
R
W
R
AV2 IN
R
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder, video game
or stereo system, etc.....
YPbPr can support these video fomats: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p.
Note: 1.AV and YPbPr share one audio channel.
2.When HDMI 1 port get DVI signal, the "PC Audio" channel is changed to receive the audio for
HDMI1 port.
3.Sometimes it will not support in different device because the device supplys nonstandard signal.
4.When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT signal is
AV; other sources have no AV OUT signal.
-10-
INSTALLATION
AV EQUIPMENT (L24M3)
This TV provides two groups of AV, one group of YPbPr for convenient connection to VCR, DVD or other
video equipment. Please refer to the owner's manual of the equipment to be connected as well.
You can use the input terminals on TV set rear as follows.
VIDEO EQUIPMENT with YPbPr
W
R
PC
AV2 IN/AV OUT
AUDIO INPUT
W
RF INPUT
AV OUT
R
W
Y
Y
Yellow (video)
R
Red (audio R)
W
White(audio L)
R
Red(Pr or Cr)
B
Blue(Pb or Cb)
G
Green(Y)
Y
HDMI
HDMI1 INPUT
VIDEO EQUIPMENT
with
terminal
HDMI2 INPUT
GBR
W
R
G B R
Pb
L
RAVPrY
W
Y
R
To audio
outputs
RWY
To video
output
AV2 IN
R
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder, video game
or stereo system, etc.....
YPbPr can support these video fomats: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p.
Note: 1.AV and YPbPr share one audio channel.
2.When HDMI 1 port get DVI signal, the "PC Audio" channel is changed to receive the audio for
HDMI1 port.
3.Sometimes it will not support in different device because the device supplys nonstandard signal.
4.When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT signal is
AV; other sources have no AV OUT signal.
-11-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Insert Batteries Into the Remote Control
1 2
1. Remove the battery cover.
2. Inserting the 2 AAA 1.5V batteries making sure the
polarity (+ or -) of the batteries matches the polarity
marks inside the unit.
3. Mount the battery cover.
Replace with new batteries when the TV set begins
to show the following symptoms:
Operation is unsteady or erratic. Sometimes the TV
set does not function with Remote Control Unit.
Remark:
1) Alkaline Battery Recommended.
2) Remove batteries when they are exhausted or if the
remote control is not to be used for long time.
3
REMOTE CONTROLLER
1:POWER
To set the TV to standby or power on.
2:NUMBER KEY
For direct access to channels.
3:MENU
To display the menu.
4:CURSOR
To move within the menu.
5:CH. LIST
To display the channel list.
6:VOL+/-
To adjust the sound level.
7:PIC
To switch the picture mode.
8:SLEEP
the time to turn off the TV.
Set
91011122526
SOURCE HOT KEYS
Switch to the source that you want directly.
13:Be used in programme edit:
Red: delete
Green: rename
Yellow: move
Blue: skip
14:FB
Fast backward key.
15:FF
Fast forward key.
16:Info
Displays or removes the signal information.
17:MUTE
To disable or enable the sound.
18:RECALL
To access the previously viewed programme.
19:SOURCE
To display source menu.
20:OK
In menu mode, use this key to confirm.
21:EXIT
Used to return to the previous menu or exit menu.
22:SOUND
To switch sound mode.
23:CH+/CH-
To access the next or previous TV Program.
24:ASPECT
To change the picture aspect ratio: 16:9 or 4:3.
27:PREV
Next key.
28:NEXT
Previous key.
29:STOP
Stop key.
30:PLAY/PAUSE
Play / Pause key.
-12-
1. CHANNEL MENU
The first item of the MENU is channel menu ( for
TV source only).
You can search channels and edit programs here.
Press to move, press OK button to confirm,
and press to adjust.
Auto Tuning
ATV Manual Tuning
Programme Edit
Software Update(USB)
CHANNEL
< >< >
1).Auto tuning:
Search all the TV channels automatically.
2). Manual tuning:
You can change the sound system to search
the TV channels and fine tune the channels,
then storage the channels you selected.
Manual Tuning
__
Storage To 1
System DK
Current CH 1
Search
Fine-Tune
Frequency 55.25 MHz
Save MENU
++
TV OPERATION
Delete
Delete
Press teletext red button, it will shows red delete
cursor.
Press to choose the program.
Press red button again, the program will delete.
Rename
Rename
Move the cursor to the program, press teletext
green button to rename the program.
Press to choose the character. Press to
move the cursor.
Press MENU button to exit edit, Press EXIT to exit
the menu.
Note: The TV programs name only can be 5 characters.
Move
Move
Move the cursor to the program, press teletext
yellow button, it will show yellow cursor, Press
to move the program.
Skip
Skip
Press to choose the program, press teletext
blue button to skip this program, The icon will
show on the right side of the program.
Choose the skipped program, press the blue button
again, you can cancel the skip, Then the icon will
disappear.
4). Software update(USB):
Update the TV set' s software by USB.
2. PICTURE MENU
The second item of the MENU is PICTURE MENU.
You can adjust picture effect here, such as contrast,
brightness, etc.
Press to move, press OK button to confirm,
and press to adjust.
NOTE:
Press teletext red button to storage to channels
after manual tuning .
3). Program Edit:
You can Delete, Rename, Move, or Skip any programs.
Programme Edit
1
2
3
Delete Rename Move
OK
Skip
MENU
Picture Mode Standard
Color Temperature
Aspect Ratio
Noise Reduction
Screen
PICTURE
< >< >
NOTE:
1).Tint is available in NTSC system only.
2).There are four color temperature modes
can be selected, such as medium, warm, cool,
and user.
3).Screen is available in PC mode only, which
can adjust horizontal position, vertical position,
size and phase.
-13-
3. SOUND MENU
The third item of the MENU is the SOUND
MENU.
You can adjust the sound effect here such as
treble, bass, balance etc.
Press to move, press OK button to confirm,
and press to adjust.
Sound Mode Music
Balance
Auto Volume
EQ
TV OPERATION
OSD Language English
Restore Factory Default
OPTION
< >< >
SOUND
< >< >
Note:
Auto volume: only available when the input
signal volume is too large or distortion.
EQ: Amplify the selected sound frequency as you wish.
4. TIME MENU
The forth item of the menu is the TIME MENU
You can adjust the clock, power on/off time,
sleep time etc.
Press to move, press OK button to confirm,
and press to adjust.
Clock 01/Jan 00:00
Off Time
On Time
Sleep Timer
TIME
< >< >
NOTE:
Within 15 minutes there is no signal, the TV
will auto sleep.
Once you power off the TV set by AC, the clock time
will be reset.
5.OPTION MENU
The fifth item of the MENU is the OPTION MENU.
You can adjust the OSD language or Restore factory
default.
NOTE:
Restore factory default will clear all the programs
and Reset all the settings to default value.
6. APPLICATION MENU
The sixth item of the MENU is the APPLICATION
MENU.
USB
APPLICATION
< >< >
Press OK button to enter the USB menu.
USB 2.0
PHOTO MUSIC MOVIE TEXT
Please make sure that the USB device have plugged in
the slot. There are four type media item can be selected,
such as photo, music, Movie and text. Select the type
media item by pressing , press OK button to enter
the disk selection menu.
In the movie mode, when you use FB, FF function, The
audio may be pause in several seconds to synchronize
the audio signal and video signal.
In text mode, press to make page up and page down.
NOTE:
When the USB device isn't supported, it may be that the
power of the USB device isn't enough.
-14-
1/1
Return C
Press the to select the right disk and press OK to
display media files and folder list or choose Return to
back to the media type selection menu.
1/1
Return
Movies
Sample1.ts
Sample1.ts Sample2.ts Sample3.ts Sample4.ts
Select the media file by pressing or , then
the preview frame will pop up. Press the button
to play the media file in full screen. When the
media file (photo, music, Movie or text type) is
playing, press the OK or Info button can display the
control bar.
Resolution: 688x412
AudioTrack: 1/2
Subtitle: 1/3
Program: 1/5
Size: 511457 KBytes
TV OPERATION
Press to select the function icon, press OK button to
confirm the function.
Press or EXIT button to exit the control bar.
NOTE:
You can adjust the audio track, subtitle, or program in
the Info menu while Playing the video file.
Choose the Info icon and press OK can display the Info
MENU.
Sample1.ts
Resolution: 720x576
AudioTrack: 1/2 ½
Subtitle: 1/3
Program: 1/6
Size: 30574 KBytes
Close
Pause Prev. Next Stop
Music function need to put music and picture in the
same folder.
Pause FF Prev. NextFB Stop
Repeat ALL
Music
Playlist
00:00:33/00:04:22
Repeat ALL
Info.
Info.
-15-
Trouble phenomenon
TROUBLE SHOOTING
Picture Audio
Snow Noise
Ghost
Interfere
Normal Picture
No picture Mute
No color Normal audio color control
Normal audio
Noise
Mute
Inspection
antenna position, direction
or connection
antenna position, direction
or connection
electronic equipment,car/
motorcycle,fluorescent light
Volume(inspect wether the
mute function on the remote
control are started , or audio
system are correct or not)
Power cord is not inserted
Power switch is not opened
Contrast and brightness/volume
setup
Press standby key on the remote
control for inspecting
Scramble
No color
Normal audio
or weak
Noise
retune channel
Audio system
Special Explanation The accessories such as remote control is not belongs
to the guarantee
-16-
Loading...