Incorrect usage will cause fire or electric shock. To prevent this, please do
as required when you are installing, using and cleaning this machine. To insure
your safety and extend the life-span of LCD-TV, please read the following items
carefully before using:
l Please read and understand all the instructions before operation;
l Please keep the book for later use;
l Please comply with the warning instructions on the machine and in this book
strictly;
l Please comply with the instructions provided;
l Please do not use additional devices that are not recommended by
manufacturer:
l Before operation, please make sure that the operating voltage of your unit is
normal;
l Do not place the unit on unstable, dusty and humid places;
l Never put the unit in direct sunlight or near heat sources;
l Allow enough space for proper ventilation;
l Please keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
l Do not remove the back cover. If services were need, please refer to qualified
Personnel
Front Panel Controls
32
TV/AV MENU VOL- VOL+ CH- CH+ POWER
(FRONT)
4
5
6
7
1
Control Panel Function
1. Power supply switch
2.TV/AV Select the input signals: TV/AV/S-VIDEO/PC/COMPONENT
3. MENU Press to select the main menu
4. VOL- Volume down / Left orientation to adjust the item in the OSD
VOL+ Volume up / Right orientation to adjust the item/Press to enter
5. CH- TV channel down / to select the item in the menu
CH+ TV channel up / to select the item in the menu
6. Power indicator
Illuminates red in standby mode, illuminates green when the display is
turned on
7.Remote Sensor Receiving remote control sends the infrared remote
signal.
Connection Options
HDMI
VGA IN
Pb/Cb
COMPONENT IN
Pr/Cr Y
S-VIDEO
L V
R
PC AUDIO IN AUDIO IN VIDEO IN
ANT IN
(BACK)
R
L V
PC AUDIO INAUDIO INVIDEO IN
S-VIDEO
Pb/Cb
Pr/Cr Y
COMPONENT IN
ANT IN
VGA IN
HDMI
1.ANT IN(Antenna Input)
Connect cable or antenna signals to the TV, either directly or through your
cable box.
2.Earphone port
3.PC Audio Input
Connect the PC output connector from a PC to the audio input port.
4.
AV /S-VIDEO/COMPONENT Audio Input
Connect audio output from an external device to this jack.
5.
Video Input
Connect video output from an external device to this jack.
6.S-VIDEO
Connect S-Video out from an S-Video device to the jacks.
7.
Component Input
Connect a component video device to these jacks.
8.VGA
Connect to the VGA 15PIN analog output connector of a PC graphics card
to use set as a PC display.
9.HDMI
Connect to HDMI output of other equipment.
Remote Control Key Functions
When using the remote control, aim it
towards the remote sensor on the TV
SLEEP DISPLAY MUTE POWER
NICAMPC AUTO AD TV/AV
PSM
OKQ.VIEW
P+
V-V+
MENU
INDEXTEXT
TIMEHOLDSIZEREVEAL
P-
SUBCODE MIX
SM
S
Buttons on the remote control
Stand By
MUTE
Display current input signal information
TV channel number select
Set time to change the TV into the
standby status after a period of preset
time.
NICAM/A2 Stereo select
EXIT
Quick TV channel switch(return to the
last channel)
Volume down/up Left/right orientation to
adjust the item in the OSD
TV channel up/down or select the item
of the menu
Select TV/AV/S-VIDEO/PC/
COMPONENT/HDMI
Select picture mode
PC system select
Select sound mode
Correspond to the differently colored
subjects
Switch to the Teletext with text mode/turn
off Teletext and switch to TV mode
Hold on or off for current page display
Switch to the Teletext with mix mode
Request index page
Change display size
Sub coded page access
While in normal TV mode only, pressing
the button TIME will display the teletext
time in the top right corner for a few
seconds.(only available in teletext mode)
Reveal or hidden the hidden words
Press to select the main menu
Auto adjust (PC mode)
Remote Control
Installing Batteries
1.Slide open the cover of the battery compartment on the back of the remote
control.
2.Load two 5# alkaline batteries in the compartment. (plus and minus poles to
respective mark)
3.Replace the cover of the battery compartment.
1
2
Precautions
Make sure that there is no
obstacle between the remote
controller and television set.
Keep the remote controller
away from heat source or
humid area to ensure
effective performance of
the remote controller.
3
As strong light may interfere the
signals, change your position to
operate the remote controller if
the television cannot be turned
on or off as you expect.
Make sure that two 5# 1.5V alkaline
batteries are loaded. The batteries
must be of the same type. The batteries
must be located properly. The batteries
are not rechargeable.
Loading...
+ 18 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.