Note: HDMI instruction in this manual is just for the special models which have the terminal.
(HDMI terminal is only available in some models, please see the real)
Safety Notice Items
Incorrect usage will cause fire or electric shock. To prevent this, please do
as required when you are installing, using and cleaning this machine. To insure
your safety and extend the life-span of LCD-TV, please read the following items
carefully before using:
Please read and understand all the instructions before operation;
Please keep the book for later use;
Please comply with the warning instructions on the machine and in this book
strictly;
Please comply with the instructions provided;
Please do not use additional devices that are not recommended by
manufacturer:
Before operation, please make sure that the operating voltage of your unit is
normal;
Do not place the unit on unstable, dusty and humid places;
Never put the unit in direct sunlight or near heat sources;
Allow enough space for proper ventilation;
Please keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
Do not remove the back cover. If services were need, please refer to qualified
Personnel
Connection Options
ANTIN
AUDIOIN
PrS-VIDEO
Pb
Y
TVSCARTVGAIN
HDMI
The figure is just for reference, please see the real.)
COMPONENT Input
Connect a component
COMPONENT/
SVIDEO /VGA
Audio Input
Connect the PC output
connector from a PC to
the audio input port
video/audio
device to these jacks
SCART
Connect to the DVD/
VCR/broadcasting
receiver or other
equipment
Connect to HDMI
output of other
equipment
HDMI
ANT IN
AUDIO IN
Earphone port
Antenna Input
Connect cable or
antenna signals to
the TV, either direcÂtly or through your
cable box.
PrS-VIDEO
Y
Pb
S-Video Input
Connect S-Video out
from an S-Video device
to the jacks.
TV SCARTVGA IN
PC Input
Connect to the VGA
15PIN analog output
connector of the PC
display card for PC
display purpose
HDMI
Remote Control Key Functions
When using the remote control, aim it
towards the remote sensor on the TV
SLEEP DISPLAY MUTE POWER
NICAMPC AUTO AD TV/AV
PSM
OKQ.VIEW
P+
V-V+
MENU
INDEXTEXT
TIMEHOLDSIZEREVEAL
P-
SUBCODE MIX
SM
S
Buttons on the remote control
Stand By
MUTE
Display current input signal information
TV channel number select
Set time to change the TV into the
standby status after a period of preset
time.
NICAM/A2 Stereo select
EXIT
Quick TV channel switch(return to the
last channel)
Volume down/up Left/right orientation to
adjust the item in the OSD
TV channel up/down or select the item
of the menu
Select PC/COMPONENT/HDMI/TV/SCART/
SVIDEO
Select picture mode
PC system select
Select sound mode
Correspond to the differently colored
subjects
Switch to the Teletext with text mode/turn
off Teletext and switch to TV mode
Hold on or off for current page display
Switch to the Teletext with mix mode
Request index page
Change display size
Sub coded page access
While in normal TV mode only, pressing
the button TIME will display the teletext
time in the top right corner for a few
seconds.(only available in teletext mode)
Reveal or hidden the hidden words
Press to select the main menu
Auto adjust (PC mode)
Remote Control
Installing Batteries
1.Slide open the cover of the battery compartment on the back of the remote
control.
2.Load two 5# alkaline batteries in the compartment. (plus and minus poles to
respective mark)
3.Replace the cover of the battery compartment.
1
2
Precautions
Make sure that there is no
obstacle between the remote
controller and television set.
Keep the remote controller
away from heat source or
humid area to ensure
effective performance of
the remote controller.
3
As strong light may interfere the
signals, change your position to
operate the remote controller if
the television cannot be turned
on or off as you expect.
Make sure that two 5# 1.5V alkaline
batteries are loaded. The batteries
must be of the same type. The batteries
must be located properly. The batteries
are not rechargeable.
Connection Instructions
Grounding
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connecting it to telephone wires, lightening rods, or gas pipes.
External Equipment Connections
Antenna Connection
- Antenna or Cable Service with a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
wall antenna
socket
RF coaxial wire (75 ohm)
VHF antenna
UHF antenna
ANT IN
outdoor
antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
ANT IN
signal area, purchase and install a
signal amplifier.
TV s, install a 2-Way Signal Splitter
in the connections.
contact your dealer for assistance.
Note:All cables shown are just for example.
Be careful not to bend the bronze
wire when connecting the antenna.
To improve picture quality in a poor
If the antenna needs to be split for two
If the antenna is not installed properly,
Connection Instructions
VGA Input
You can use your LCD-TV as a monitor for your personal computer using a VGA
cable (not supplied).
Connection and use steps:
1.Read the user guide supplied with
your computer and ensure that it has
a VGA connector;
2.Make sure that the power of the LCD
-TV and the PC are off;
3.Connect a D type 15-pin VGA interface
cable ( not supplied ) to the VGA video
interface connector on the PC. Then
connect the other end to the PC video
interface connector on the back of the
LCD-TV.Tighten the screws on the VGA
connectors once they are firmly
connected;
4.Turn on the power of the LCD-TV first ,
and then turn on the power of the PC;
5.Press the TV/AV button to set the video
input mode of the LCD-TV to PC;
6.Check the image on your TV. There may be noise associated with the resolution,
vertical pattern, contrast or brightness in PC mode. If noise is present, change
the PC mode to another resolution, change the refresh rate to another rate or
adjust the brightness and contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card can not be changed,change the PC graphic
card or consult the manufacturer of the PC graphic card.
Resolution
ModeResolution
VGA
SVGA
XGA
Note: All above listed are subject to VESA Criteria.
640*48031.5KHz60Hz
800*60037.9KHz60Hz
1024*76848.4KHz60Hz
VGA IN
Frame frequency (Hz)Line frequency (Khz)
YPbPr Input
How to connect
Connect the DVD video outputs (Y, PB, PR)
to the COMPONENT(Y, Pb, Pr) IN jacks on
the TV and connect the DVD audio outputs
to the AUDIO IN jacks on the TV, as shown
in the figure.
NOTE: If your DVD player does not have
component video output,use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the TV/AV button on the remote control to select
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.