Haier KXT7020S, KXT7020BK User Manual

11. Warranty

This Haier brand product, when shipped in its original container, will be

free from defective workmanship and materials, and agrees that it will, at

its option, either repair the defect or replace the defective product with a

new or re-manufactured equivalent at no change to the purchaser, for parts

or labor for the periods set forth below:

This warranty does not apply to the appearance of the product or the

exterior of the product, which has been damaged or defaced, altered or

modified in design or construction. It does not apply to the additional

excluded items set forth below:

The warranty commences on the date the item was purchased and the

original purchase receipt must be presented to the authorized service

center before warranty repairs are rendered.

The limited warranty described herein is in addition to whatever implied

warranties may be granted to purchasers by law. ALL IMPLIED

WARRANTIES INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO

THE PERIOD(s) FROM THE DATE OF PURCHASE SET FORTH

BELOW. Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized

to make any warranties other than those described herein, or to extend the

duration of any warranties beyond the time period described herein on

behalf of Haier.

The warranties described herein shall be the sole and exclusive warranties

granted by Haier and shall be the sole and exclusive remedy available to

the purchaser. Correction of defects in the manner and for the period of

time described herein, shall constitute complete fulfillment of all abilities

and Responsibility of Haier to the purchaser with respect to the product,

and shall constitute full satisfaction of all claims, whether based on

contract, negligence, strict duality or otherwise. In no event shall Haier be

liable, or in any way responsible for any damages or defects in the product

which were caused by repairs or attempted repairs performed by anyone

other than an authorized service center or dealer; nor shall Haier be liable,

or in any way responsible for incidental or consequential economic or

property damage. Some states do not allow the exclusion of incidental or

consequential damages, so that above exclusion may not apply to you.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU

MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE

TO STATE.

Warranty period for this product: 90 days for Labor, one year for parts.

Additional items excluded from warranty coverage: non-rechargeable

batteries.

Where to obtain service: For the location of the nearest Haier authorized

service center or to obtain product literature, accessories, supplies or

customer assistance, please call 1-877-337-3639.

What to do obtain service: ship or carry in your product to an authorized

service dealer or center. Be sure to have proof or purchase.

If you ship the product, be sure it is packaged carefully.

Haier America

New York, NY 10018

15

Instruction Manual

Portable 7" COLOR TFT LCD TELEVISION SET

Dear Customers:
Thank you for purchasing this product.
Please read this manual carefully before connecting, operating or
 adjusting this product in order to ensure the best efficiency and
 safety of this product. Please keep the manual for future reference.

Model No. : KXT7020BK / KXT7020S

AV/TV

MUTE

CH+

PIC SETUP

TUNE

CH-

2

4

POWER

VOL+VOL-

9

Table of Contents

1. User Safety Instructions------------------------------------------------------(2)

2. Basic Characteristics and Functions---------------------------------------(3)

3. General Parts---------------------------------------------------------------(3-5)

4. Connection--------------------------------------------------------------------(6)

5. Operation Instructions-----------------------------------------------------(7-8)

6. Battery Installation----------------------------------------------------------(11)

7. Stand Fixture-----------------------------------------------------------------(11)

8. General Specification-------------------------------------------------------(12)

9. General Troubleshooting---------------------------------------------------(13)

10. Accessories List------------------------------------------------------------(14)

11. Warranty--------------------------------------------------------------------(15)

1. Safety Instructions

1) Read these instructions carefully.

2) Keep these instructions for future reference.

3) Heed all warnings.

4) Follow all instructions.

5) Do not expose to water or moisture.

6) Clean only with a dry cloth.

7) Keep objects away from ventilation openings. Do not block any ventilation openings at
any time.

8) Do not install near any heat sources such as stoves, computer towers, amplifiers or any
apparatus that produce heat.

9) Do not force the power plug in the wall outlet. A polarized plug as two blades with one
wider than the other. The wide blade is provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for replacement of the obselete outlet.

10) Place the power cord so that it is protected from being walked on, pinched by objects, torn
and exposed to liquids, especially at plugs, convenience receptacles, and the point where
they exit from the product.

11) Only use attachments/accessories specified by the manufacturer. Use of attachments/accessories
not recommended by the product manufacturer may cause hazards.

12) Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

13) Unplug the apparatus during lightning storms or when unused for long periods of time.

14) Do not use this apparatus near water, and no objects filled with liquids, such as vases,
shall be placed on the apparatus.

15) Refer all servicing to authorized service personnel.

For recycling or disposal information about this product,
please contact your local authorities or the Electronics
Industries Alliance: www.eiae.org

2

3. General Part

2. Basic Characteristics and Functions

1. TV System: NTSC 3.58 System

2. AV System: NTSC 3.58 System

3. Full Menu on-Screen Display

4. AUTO Search TV channel programming

5. VCD/DVD AV Equipment Connection Port

6. Brightness, Contrast & Color Adjustment

7. Stand By Mode

8. Detachable TV Battery Compartment Stand

9. Headphone Jack

10. English/Deutch/Japanese/Espanol/Chinese OSD language options

3

1. Power Button

2. Menu Button

3. Volume Down Button

4. Volume Up Button

5. Channel Down Button

6. Channel Up Down

7. AV/TV Switch

8. Remote Control Sendor

9. Direc light/Power
/Standby indicator

10. Built In Speakers

FRONT VIEW

11.Rotary Telescopic
Antenna

12. Stand Holder(Plastic)

4

18. Power Cord to DC 12V INPUT

4. Connection

ANT.

AV IN

DC IN-12V

-

+

SIDE VIEW

(2). Remote Control

AV/TV

1

11

2

3

MUTE

CH+

PIC SETUP

TUNE

CH-

2

1

5

4

7 8 9

0

13. Antenna Jack

14. AV IN Jack

15. Headphone Jack

16. Power Source Input Jack

POWER

VOL+VOL-

4

5

6
12
7

8

9

3

6

-/--

10

17. Detachable Battery Compartment Stand

(10 X "AA" <UM-3> SIZE batteries are not included)

19. Car Stand

1. AV/TV Switch

2. Volume Down Control

3. Number Selector

4. Stand By button

5. Mute Button

6. Channel Up Control

5

7. Tune Mode

8. Volume Up Control

9. Channel Down Control

10. Single/Two/Three Digits Selector

11. Picture Button

12. Set Up Button

1. Connection of the Antenna (See picture 1-1)
Plug the antenna into the ANT jack (13).
NOTE: The unit can receive CATV/ANT signals from the ANT jack input.

2. Connection of the External AV Equipment (See picture 1-1)
Plug the AV cable into the AV IN jack(14) . (Press AV/TV button(1) to enable the con­ nection of external audio and video equipment).

3. Use of Earphone (See picture 1-1)

- Connect the Earphone to " " at (15) for private listening.

- The speakers will not operate when headphones are connected.
CAUTION : Listening at high power for too long could damage your ears.

4. Connection to the Power Source
(1) Connect one round end of attached AC adaptor or car adaptor to the power source
input jack (16 ) and the other end to the wall outlet at the suitable voltage .(1-1)
(2) Connect the detachable battery compartment stand power cord to the power source
input jack (16). (See picture 1-2)

Antenna

ANT.

AV IN

DC IN-12V

-

+

Red

YELLOW

AUDIO INPUT

VIDEO INPUT

Earphone

AC Adaptor

Detachable Battery Compartment Stand

(10 x "AA" <UM-3> SIZE batteries are not included)

(Options)

AC Adaptor

Power Cord to
DC 12V Input

(Options)

(1-2)(1-1)

6

ANT.

AV IN

DC IN-12V

-

+

5. The operation of the TV set and remote control

1. The POWER button

After plugging the unit in the power light(9) should be red, press the POWER
button of the unit or the remote to turn the unit on and off.

2. MENU /PIC/SETUP/TUNE button
The MENU button of the unit controls the following three on-screen functions:

1) PICTURE: To adjust brightness, contrast, etc.

2) FUNCTION: To adjust system , language, and clock functions.

3) PRESET: To adjust auto search, add/delete, fine tuning, etc.

Press the MENU button to scroll through these three on-screen options.

PICTURE FUNCTION PRESET

- FUNCTION

Press MENU button of the unit again or the SETUP button on the remote until
FUNCTION screen appears (see picture 2-4).

Press CH up or CH down to scroll through these options.
Press VOL up or VOL down to adjust each option.

FUNCTION

- PICTURE

Press MENU button of the unit once or the PIC button on the remote to enter.
The PICTURE screen will show the following content (see picture 2-3).
Press CH up or CH down to scroll through these options.
Press VOL up or VOL down to adjust each option.

PICTURE

BRIGHT 32
CONTRAST 32
COLOR 32
TINT 00

2-3

- BRIGHT
Press VOL up to make picture brighter and VOL
down to make picture darker.

- CONTRAST
Press VOL up to increase contrast and VOL down
to decrease contrast.

- COLOR
Press VOL up or VOL down to adjust color levels.

- TINT
Press VOL up or VOL down to adjust tint levels.

2-2

7

- SYSTEM

System has been disabled for this unit.

- LANGUAGE

The unit support OSD language in English/Deutch/Japanese/Espanol/Chinese.

- TIMER
VOL up is used for setting hour, Press VOL up one time, the time will add one
hour. VOL down is used for setting minutes. Press VOL down one time and the
Clock will add one minute.

2-4

8

- PRESET

Press MENU button of the unit or the TUNE button on the remote
until the PRESET screen appears (see picture 2-5).

Press CH up or CH down to scroll through these options.
Press VOL up or VOL down to adjust the desired option.

PRESET

PROG 120
SKIP OFF
BAND VHF-L
FINE
SIGNAL CATV
AUTO

- PROG
This function shows the current channel displayed. Use the VOL up
or VOL down buttons to scroll through the channels.

- SKIP

This function allows you to add or delete any channel. If you would
like to delete a channel simply navigate to the desired channel with
the PROG button and press the VOL up or VOL down button until
this function reads “ON”.
If you would like to add a channel simply press the VOL up or VOL

2-5

down button until the SKIP feature reads “OFF”.

- BAND

This feature simply displays what type of frequency is currently displayed (UHF, VHF, etc).
The BAND function can not be adjusted.

- FINE
The FINE feature controls the fine tuning of each channel. Use the VOL up and VOL down but­ tons to fine tune each frequency for better sound and picture.

- SIGNAL
The unit can work with both cable TV and an antenna. Simply adjust this feature to either ANT
for use with an antenna or CATV for use with cable TV.
The unit can receive up to 80 channels with the antenna setting (ANT) and 136 channels with
cable TV(CATV) setting.

9

- AUTO
Use this feature to program all available channels. Use the CH up or CH down
button to highlight the AUTO feature. Then, press VOL up or VOL down to initiate
this feature. Allow the unit to search all possible channels.
NOTE:
If some channels do not have sound use the FINE feature to fine-tune the channel.
If sound does not appear please refer to the Troubleshooting section.

3. AV/TV button
Use the AV/TV button to switch between watching VIDEO and TV. Switch to
VIDEO. when using an external video source such as a DVD or VCR. Switch to
TV to watch TV through the antenna or cable TV.

4. MUTE button
Press the MUTE button one time, there is mute signal on the screen, press again,
the volume will resume.

5. VOL up / VOL down button
Use the VOL up and VOL down buttons to adjust the volume of the unit. The
volume range is 0-63. VOL up and VOL down buttons are also used to adjust
features in the MENU.

6. CH up/ CH down button
Use the CH up and CH down buttons to go from channel to channel. Also use the
CH up and CH down buttons to navigate the MENU functions.

7. NUMERICAL button(0-9)
Numerical button 0-9 is used for selecting program number , button 0-9 has the
function of power on when the TV is in waiting status.

8. -/-- button
If you want to select two-figure or there-figure program number , you need to
press -/-- button, after -/-- shows on the screen, you can use the numerical button
to input the desired program number.

10

6. Battery Installation( Optional):

Open and remove the battery door located on
the bottom of the battery compartment stand
and pulling firmly outwards. Insert 10 "AA"
x (UM-3) batteriesinto thebatterycompartment
(see right picture). Be sure the polarity (+and-)
matches,as made inside thebattery compartment.
Closethe battery door and connect the power cord
ofthe battery compartment to the power source
input jack of the unit.

NOTE:

- Weak or dead batteries may leak or corrode the set. Always remove batteries

when the set will not be used for a long period of time.

- When the battery box is being charged, forbid the battery box to connect
with a machine, watch TV.

7. Stand Fixture(Optional)

- Release the metal washer on the top of
the stand but should not separate it from
the stand (see picture 3-1).

- Insert the metal washer with the stand
into a hollow at the back of the unit and

3-2

move the stand up to a suitable height
(see picture 3-2).

- Tighten the screw 1 (see picture 3-3) up

Met

al

w

ashe

r

on the stand to fix the stand with the unit.

- Control the unit direction by controlling
the screw 2 (see picture 3-3).

3-1

+ – + – + – + – + –

3-3

+ – + – + – + – + –

Screw1
Screw2

8. General Specification:

1.  Description: Portable 7” TFT LCD Color TV Set

2.  TV System: NTSC 3.58 System

3.  AV System: NTSC 3.58

4.  Audio System: M

5.  Display device: Color TFT-LCD

6.  Display Screen Size: 7 inches

7.  Video Input: 1Vp-p

8.  Audio Output: O250mW (MAX)

9.  Power Consumption: o11w

10. Resolution: 1440 (H)*234 (V)

11. Dots Distance: 0.107(H) X 0.372(V)mm

12. Visible Range: 154.08(H) X 87.05(V)mm

13. Power Source: AC adaptor or car adaptor (normal: DC 12V)

14. Measurement: 195 (L) X 135 (W) X 30(D) inches

15. Weight: Approx. 490 lbs

16. Connection terminals:
1. Antenna Jack
2. AV Input Jack
3. Headphone Jack
4. External Power Source Input Jack

11

12

9. General Troubleshooting

Check the following points before assuming malfunctions of the TV set:

Problem Reasons

No picture & sound

No picture

No sound

Poor reception

Dark or blurred picture

Unclear or unstable picture

Picture moves up &
down, blurs or folds over

Sound on some channels
but not all

No color

Improper connection of AC adaptor or car adaptor.

The batteries are run down or installed incorrectly..

Antenna is not properly attached. Relocate the TV to a place
where reception is better.

Sound volume is too low. The signal is too weak.

TV antenna is not adjusted properly or reception is too weak.

The brightness & contrast are too low.

TV antenna is not properly adjusted or reception is too weak.

TV antenna is not adjusted correctly. The reception is too
weak or compromised by buildings or nearby mountains.

Adjust FINE function up or down in the MENU until sound
is clear.

Color is not set correctly..

13

10. Accessories List

Name

AC Adaptor

Remote Control

AV Cable RCA Jack

Car Cord

Car Stand

Instruction Manual

Exterior Antenna Jack

Fixed Screws (PWA3*14)

Battery Compartment

Earphone

Quantity

1 piece

1 piece

1 piece

1 piece

1 piece

1 piece

1 piece

4 pieces

1 piece

1 piece

14