Haier HWT90MW2, HWT80MW2 User Manual

50

50

The purpose of the bottom plate is to suppress noise
from the washing machine during operation.
Steps:

1.Lay the washer on its back,on a non-abrasive surface.

2.Insert the bottom plate to the bottom of the machine.

3.Use a screwdriver to tighten the screw(in accessory
bag) securing the plate to bottom of the washer.

4.Once the screw is tight and the plate is secure,return
the washer to its standing position.

Screw

Bottom plate Carpet

Front

Back

1

2

3

Detergent Usage Guide

Adding washing power

Liquid detergent box

Washing

powder inlet

Softener inlet

Detergent box

How to use liquid detergent

Put the liquid detergent box on the right of the

detergent box. See the above figure.
Before washing put the liquid detergent into the

liquid detergent box directly as indicated the above
figure. The usage and dose of the liquid detergent
as per the specifications of liquid detergent.

How to use softener

The usage and dose of the softener as per
the specifications of softener.

Before washing put the softener into the
detergent box directly. See the above figure.
The softener will put into the washer when the
last rinsing.

After that,please close the detergent box refer to
the following list for the usage of the detergent:
selection of the water level,water quantity and
dosage of detergent

After the softener is put in,please don't place for
a long time otherwise softener may solidify and

cause flowing not smooth.
When water pressure is too low, it is possible

that softener cannot be washed away effectively,
and softener would be agglomerated after a
period of time. Please clean the softener box in
time. It is recommended to pour the softener
into the basket directly after water is filled at the
last rinse.

Adding washing powder Cotton Wash

If you select “Express”program,it is recommended to use

When water pressure is too low, it is possible that washing powder or
washing liquid cannot be washed away effectively, and washing powder
or washing liquid would be agglomerated after a period of time. Please
clean the detergent box in time. It is recommended to pour the washing
powder or liquid into the basket directly.

If a manufacture specifies only the use of a low-sudsing or
high-efficiency type detergent, then detergent for drum type machines
shall be used irrespective of the type of machine under test.
Otherwise the detergent type to be used shall be chosen according to
the type of clothes washing machine under test, as follows.

Low

Lightly soiled or small laundry loads less than 1.5kg

Remove

Trouble-shooting

by yourself.

if the machine

The machine does not
drain or drain slowly.
The display shows E1.

The machine stops running.
The display shows E2.

The machine does not
spin.The display shows E3.

The display shows E4.

The display shows FC.

The display shows FA.

Will not

wash

The machine
does not work.

Will not

spin

There are abnormal
sounds inside the machine.

The water tap leaks.

The display shows E9.

The display shows E8.

The display shows F2.

Is the drain hose blocked?

The top lid is not closed.

Has the laundry been placed
unevenly in the machine?

Is the machine level?

Is the water tap closed or

has the water supply been
interrupted?

Is the water inlet valve

blocked?

Is the water pressure too low?
Is the drain hose set too low?

Communication failure
between display board

and motor driver.

The water level sensor has

failed.

Is there a power failure?
Is the power plug inserted
tightly?

Has the water level reached

preset position?

Is the power plug inserted
tightly?
Is the top lid closed?
Is the laundry distributed
unevenly in the machine?

Is the machine level?
Has the laundry been placed
unevenly in the machine?

Are there any foreign objects

inside the bowl?
Is the water inlet hose loose?

Communication failure between
show board and power board.

Is the door lock broken?

Over flow Error

Remove the blockage.
Push the Start/Pause button
once.

Close the top lid. Push the
Start/Pause button once.
Redistribute the load evenly.
Push the Start/Pause button
once.

Level the machine.

Open the water tap. Push

the Start/Pause button once.
Clean the water inlet valve

then push the Start/Pause

button once.
Use after the water pressure

is normal.

The height of the end of the
drain hose should be between
800mm-1200mm.

Please contact Customer Care.

Please contact Customer Care.

Wait for the power supply to
be restored.
Insert the power plug tightly.
Wait for the water to fill to the

preset level.

Insert the power plug tightly.

Close the top lid.
Redistribute the laundry.

Level the machine.
Redistribute the load evenly.
Close the top lid.
Remove the foreign object.

Fasten the inlet hose.

Please contact Customer Care.

Please contact Customer Care.

Please contact Customer Care.