Specification
Rated Washing capacity
HWT10MW2
.
350W
300W
45kg
52kg
W 610 D 620 H 1045
10kg
TOP LOAD FULLY AUTOMATIC WASHING MACHINE
OWNER’S MANUAL
MODEL: HWT10MW2
Please read this manual carefully before
operating your washing machine and retain
it for future reference.
Safety precautions
Installation & Adjustment
Loading your laundry
Detergent usage guide
Operation & Wash cycles
Location
Warranty card
Bracket
One
On The Drain hose
Product overview
Top lid component
Detergent box
Outer tub cover
Inner tub
Filter frame
Control pannel seat
Pulsator
Cabinet
Base frame
Adjustable foot(2pieces)
Screw cover
Back panel
Water absorption gasket
Cold water inlet valve
Hot water inlet valve
Hook
Power cord
Back cover
Drain hose joint
Fixed foot(2 pieces)
an injury to the
Warning
if the machine
A separate, earthed power socket is
required for the power supply. Hold the
plug-NOT the electric cable-when
unplugging the washing machine. Do not
insert or remove the power plug with
wet hands. The power plug should be
accessible after the machine installation.
If the supply cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.
Ensure the plug is removed and the
taps turned off in the followng cases:
Power failure, cleaning, moving,
installation and when not in use.
Forbidden
Do not install this appliance in a damp
or wet environment. Do not leave wet
laundry on the Control Panel or spray
water directly on to this appliance,as
this may cause the washer to
malfunction
or cause an
electrical
fault.
If you are using an extension cord or a
portable electrical outlet device (not
recommended), ensure that it is
positioned so that it does not come into
contact with water
or moisture
The openings must not be obstructed by a carpet
Do not connect to hot water higer than
50°C temperature.
50
Do not wash water-proof clothing as
this may affect load balance
during spin cycle(s).
by yourself.
The machine does not
drain or drain slowly.
The display shows E1.
The machine stops running.
The display shows E2.
The machine does not
spin.The display shows E3.
The display shows E4.
The display shows FC.
The display shows FA.
Will not
wash
The machine
does not work.
Will not
spin
There are abnormal
sounds inside the machine.
The water tap leaks.
The display shows E9.
The display shows E8.
The display shows F2.
Is the drain hose blocked?
The top lid is not closed.
Has the laundry been placed
unevenly in the machine?
Is the machine level?
Is the water tap closed or
has the water supply been
interrupted?
Is the water inlet valve
blocked?
Is the water pressure too low?
Is the drain hose set too low?
Communication failure
between display board
and motor driver.
The water level sensor has
failed.
Is there a power failure?
Is the power plug inserted
tightly?
Has the water level reached
preset position?
Is the power plug inserted
tightly?
Is the top lid closed?
Is the laundry distributed
unevenly in the machine?
Is the machine level?
Has the laundry been placed
unevenly in the machine?
Are there any foreign objects
inside the bowl?
Is the water inlet hose loose?
Communication failure between
show board and power board.
Is the door lock broken?
Over flow Error
Remove the blockage.
Push the Start/Pause button
once.
Close the top lid. Push the
Start/Pause button once.
Redistribute the load evenly.
Push the Start/Pause button
once.
Level the machine.
Open the water tap. Push
the Start/Pause button once.
Clean the water inlet valve
then push the Start/Pause
button once.
Use after the water pressure
is normal.
The height of the end of the
drain hose should be between
800mm-1200mm.
Please contact Customer Care.
Please contact Customer Care.
Wait for the power supply to
be restored.
Insert the power plug tightly.
Wait for the water to fill to the
preset level.
Insert the power plug tightly.
Close the top lid.
Redistribute the laundry.
Level the machine.
Redistribute the load evenly.
Close the top lid.
Remove the foreign object.
Fasten the inlet hose.
Please contact Customer Care.
Please contact Customer Care.
Please contact Customer Care.
Clean the detergent box and set it on the
control panel seat.
1.Dismantle: Pull the detergent box, then hold
two sides with hands.Press downwards and
pull meanwhile, then it can be pulled out.
2.Clean: Use a brush and duster cloth to clean
.
it, then flush it with water.
3.Install : Install it upwards and push it in.
Remove
The lint filter must be used during washing.
It must be cleaned in time after each using.
Lint filter:
1.Push down the spring piece of the top lint filter to
make the claws out of the filter cover, and then pull
out the lin t filt er to get it down.( figure 1)
2.Pull the back of the lint fil ter, and then you can get
down it off the front cover of the lint filter.(figure 2)
3.Sweep the lin t in the lint filter.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it tig ht.
6.Make sure the lin t filt er well install ed, or it can
in fluence your use.
Install
Fig ure 1
The fron t co ver of the lint filter
Up
Dismantle
Dismantle
Dow n
The bac k c over of the lint filter
Fig ure 2
Up
Install
Dow n
This product has been designed for use in a normal
domestic (residential) environment.
This product is not designed for any commercial use
(whatsoever). Any commercial use by a customer will
affect this product’s Manufacturer’s Warranty.
The applicance water pressure is 0.03MPa-1.0MPa
(when water temperature is 55℃,the water inlet
pressure of hot water shall not exceed 0.4MPa).
The maximum mass of dry cloth to be used in the
appliance is 10kg for HWT10MW2.
℃
The new hose-sets supplied with the appliance
are to be used and that old hose-sets should
not be reused.
and wall should be at least 20mm
，close the lid and press the “start/pause”,the machine will run
used，
Child Lock
Set the desired washing program,after setting, press the “Start/Pause” button,and
washing machine begin to run. Then hold the “Progress” button and “Delay” button at
the same time for more than 3 seconds，you will hear three beep sound，digital tube
display “CL”,and the child lock will activate. All of the buttons are locked, and will no
function.
To disable the child lock function:
the
“Progress” button and “Delay” button
This washer has a 2-step water fill to achieve the required water level and temperature
for the best cleaning result.
First Fill - Once options and cycle are selected and the
both hot and cold water will flow into the inner tub. The warm water temperature helps
to dissolve detergent quickly. The washing operation starts at the end of the hot water
fill and is followed by a 5-minute (approximately) soak-agitation session to help the
detergent mix completely with the laundry.
Second Fill - The second fill is in order to reach the selected water level and make
the clothes completely soaked in water to achieve a better wash effect.
the child lockafter three beep
the child Lock
at the same time for more than 3 seconds,
“ ”
Start/Pause Button is pressed,
Note:
The energy test program was performed using the "Cotton" cycle
setting of:
Soak:30 mins; Water Temp:Warm; Rinse: 1 Rinse;Spin:7 mins
Water level:Max.
If you choose the Cotton program, it is not suggested to put the
softener, because the softener can not be put in the inner tub
Please use low suds/high efficiency detergent.
Spin
During Express,Wool, Duvet , Drum Clean and Anti Crease cycles,these settings
cannot be changed and buttons will not function, as machine will only follow
pre-programmed settings.
Attention: Even there’s no water in the tub, the spinning will start after a certain period
back side of the cabinet, and fasten with drain hose clamp(provided).
the bracket
,
Bracket
For the “Cotton” and “Eco”cycles the machine will run a Fuzzy Logic program
not
Temp
“Start/Pause” button is pushed.
“Delay” button .
clamp
800-1200
0.8
Water Temp
F
Water Temp
1
2
3
During Wool and Duvet cycles, the “Hot”,“Warm”,“Max” water temperature cannot be chosen.
During Drum Clean cycle, the “Cold”,“Warm”,“Max” water temperature cannot be chosen.
During Anti Crease cycle, the “Hot”,“Max” water temperature cannot be chosen.
Start/Pause
G
Power
H
10 minutes, the washing machine will automatically
Turn Cycle button to select automatic program
When the power is switched on “Cotton” cycle is automatically set
Turn the “cycle” button to select automatic program.
Soak Time Spin TimeRinse
You may change the Soak time，Rinse and Spin time, except Express, Wool,
Anti Crease.
Progress
C
You may change the Progress,except
Anti Crease
cycles are selected.
Express,Wool, Duvet ,Drum Clean and
D
E
During the Eco and Cotton programs the washing machine will detect the size
Mid,High or
Max.
“Mid”
“Max”,
If Express program is selected it will display water level
Drum Clean
“Low”
800mm≤h≤1200mm
Check the following before washing
Check if the laundry has any special washing instructions.
D
S
F
F
D
washing powder is used
low
Mid
H
B
B
C DEF
B
A
G
Liquid detergent box
Washing
powder inlet
Softener inlet
Detergent box
How to use liquid detergent
Put the liquid detergent box on the right of the
detergent box. See the above figure.
Before washing put the liquid detergent into the
liquid detergent box directly as indicated the above
figure. The usage and dose of the liquid detergent
as per the specifications of liquid detergent.
How to use softener
The usage and dose of the softener as per
the specifications of softener.
Before washing put the softener into the
detergent box directly. See the above figure.
The softener will put into the washer when the
last rinsing.
After that,please close the detergent box refer to
the following list for the usage of the detergent:
selection of the water level,water quantity and
dosage of detergent
After the softener is put in,please don't place for
a long time otherwise softener may solidify and
cause flowing not smooth.
When water pressure is too low, it is possible
that softener cannot be washed away effectively,
and softener would be agglomerated after a
period of time. Please clean the softener box in
time. It is recommended to pour the softener
into the basket directly after water is filled at the
last rinse.
Adding washing power
Adding washing powder Cotton Wash
Low
If you select “Express”program,it is recommended to use
When water pressure is too low, it is possible that washing powder or
washing liquid cannot be washed away effectively, and washing powder
or washing liquid would be agglomerated after a period of time. Please
clean the detergent box in time. It is recommended to pour the washing
powder or liquid into the basket directly.
If a manufacture specifies only the use of a low-sudsing or
high-efficiency type detergent, then detergent for drum type machines
shall be used irrespective of the type of machine under test.
Otherwise the detergent type to be used shall be chosen according to
the type of clothes washing machine under test, as follows.
Drum Clean
knob
Washing Cotton laundries
The cycle of energy saving
Lightly soiled or small laundry loads less than 1.5kg
Washing Sports clothes
Hygienic Washing
Washing T-shirts, shirts laundries
Washing Duvet
Washing Towels
Washing Synthetic laundries
Cleaning
Loading...