Page 1
User’s Manual
Fully Automatic Washing Machine
Index
This manual is for
HWM85-7288
Safety precautions ...............
Packing list
Names of the parts
Installation and
adjustment............................
Preparation before
washing.................................
Use the operation buttons
Disposal after washing
Trouble-shooting Answer
to question............................
Specification
...........................
...............
....
.........
.........................
2
4
4
5
9
11
13
14
15
Please read this manual carefully before using.
Retain it for future reference.
Page 2
Safety precautions
Meaning and description of the symbols
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
WARNING
FORBIDDING
Please check if power receptacle has good earthing condition before using to guarantee
your safety.
Please check if the water faucet is open, and if the connection of the water inlet pipe is
proper.
It is suggested to use foamless washing powder.
Please don’t use the washer in the environment below 0 °C; if the washer has been stored
below 0°C, please be sure to ensure the washer is placed under the room temperature
more than 2 hours and then use otherwise the washing effects may be lowered or the
washer may be damaged.
cause damage of the machine or injure the personal safety
of the user.
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
Please inser t the power cord into special receptacle with rated voltage.
Be sure to use single-phase three pins receptacle.The earthing terminal of
the receptacle must be earthed reliably. If possible,please adopt electric
leakage protector.
The washing machine must be positioned so that the plug is accessible. Be
sure to pull the plug off and close the water faucet in following cases: power
failure, delivering the machine, setting the machine idle or cleaning the
machine.
Do not plug or pull the power plug with wet hand.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacles
loose, do not use the plug any more.
2
Page 3
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole
with carpet. Ensure carpet does not obstruct the
opening in the bases.
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not put wet
laundries on the control panel.
Do not wash water-proof laundries like the raincoat,
bike covers etc. to avoid abnormal vibrations
in spinning. Wash the clothes that can float
on the water surface easily, please be careful
especially,for fear damage.
Do not stretch hands into the working machine. It is
dangerous even if the rotation is slow. Take special
care of the children.
Do not put any hot or heavy items (such as the
kettle with hot water ) on the washing machine.
Do not wash laundries with volatile materials (such
as thinner, petrol etc.)
The children shall not approach the working
washing machine.
Keep the machine away from direct sunlight and
heat source like the heater.
Do not decompose, repair or alter the machine by
yourself.
Do not use water hotter than 50 °C.
3
Page 4
Packing list
Fully automatic
washing machine
Water inlet hose Bottom plate Tapping screw User’s manual
Names of the parts
Top lid
Detergent box
Control panel seat
Outer tub cover
Lint filter(2 pieces)
Balance ring
Inner tub
Filter cover(2 pieces)
Control panel film
Adjustable foot(2 pieces)
Pulsator
Cabinet
Water inlet valve
Water absorption cushion
Back control board
Warranty card
Bleach inlet
Hanging hole
Cabinet handle
Screw cover(right)
Adjustable foot film(2 pieces)
Screw cover(left)
Power line
All illustrations in this Manual are
given for reference only. Your
products and accessories may
show differences from these
illustrations due to our continuous
improvement.
4
Back cover
Drain hose
Fixed foot (2 pieces)
Page 5
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important
to your security and correct operating the machine.
After you open the package, please lean
the washing machine gently down on soft
items (like the towel cloth, blanket, ect. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
Fasten the bottom plate to
base frame with one screw
The washing machine away from wall should be overrun 20mm. The largest allowable slope
of the shank base of the machine is 2°. The slanting or rough ground will result in unstable
running or stoppage of the machine. Please adjust it with following methods:
Confirm
Hang the lead line to check if it is horizontal.
it's horizontal:
Section I enlarging
Soft items
Front
Back
Bottom plate
Adjust the adjustable foot:
To twist the adjustable foot, please fi rst lift up the side of the foot slightly, and then you
can twist the two adjustable feet. Please make sure to keep the washing machine
in balance.
High
Low
The adjustable foot
5
Page 6
NOTE:The appliance is to be connected to the water mains using new hose-sets and
that old hose-sets should not be reused.
Confirm the water faucet
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth.If not please file it to avoid leakage.
water faucet, suitable
The exit end face of the faucet
water faucet, not suitable
Connection between the water inlet hose jointer and the
water faucet
water inlet hose jointer
1.Press the lower end of the lock lever and push
down the slider. Take off the water inlet hose
jointer from the water inlet hose component.
See to Figure 1.
2.Loosen the screw till the water faucet can be
accessed. Put the jointer of the water inlet
hose on the faucet. See to Figure 2. (If the
faucet is too large and the jointer can not be
set on the water faucet,please loosen the four
screws and take out the bushing in the jointer.
The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
Lock lever
water inlet hose
Sign plate
Figure 2
Figure 1
Screw knife
Slider
Screw
Bushing
Figure 3
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut
as per the indication of the figure to seal up the
exit end face of the faucet. See to Figure 5.
Remark: Before installation, the threading is
4mm above the upper surface of the nut.After
installation, the threading is 2mm above the
upper surface of the nut.See to Figure 6.
6
Figure 5
Screw nut
Figure 4
About 4mm before twisting
About less than 2mm after twisting
Figure 6
Page 7
Connection between the water inlet hose and the washer
1.Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each usage. If it happens please contact our
after-sale department immediately.
2.Put the nut of the water inlet hose on the valve
jointer.
3.Fasten the nut. Swing it gently to confirm if it's
suitable.
jointer of the
water inlet valve
nut of t he water
inlet hose
wat er abs orption
cus hio n
Connection between the jointer of the water inlet hose and the
water inlet hose
Push down the slider. Insert the water inlet hose
1.
into the jointer.
2.Hang the lock lever to the jointer. Release the
Locking lever
The jointer of the
water inlet hose
Slider
slider till a click sound is heard.
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection between
the jointer of the water inlet hose and the water faucet, and
the installation of the water inlet hose are firm, so as to
prevent dropping from improper installation position.
Dismantle the water inlet hose
1.Close the water faucet.
2.Press the locking lever. Push down the slider.Then pull off the water inlet hose.
If the machine is used frequently, the jointer of the water inlet hose can be kept
on the faucet to prevent damaging the fixing screw.
Locking lever
Slider
7
Page 8
How to change the direction of the drain hose
1.Please lean the washing maching gently down on soft items(like the towel cloth,blanket,etc.)
2.Remove the Drain hose from the fixing clamp of the base frame.
3.Fix the drain hose in the fixing clamp on the other side.
4.Lift the maching up gently.
Remark: In order to make sure of the correct of installation, it is suggested to change the
direction of the drain hose with our company serviceman.
The drain hose shall drain smoothly.
1.
than 10cm , or the drainage will not be smooth,
and cost such long time that the machine may
stop at mid way.
Do not trample or press the drain hose.2.The height of the drain hose shall be less
3.
If the drain hose is too long, cut it at mid
point. To make smooth drainage,cut the front
end of the hose slantingly.
If the extra hose is too long,cut it either at A or at B point.
5.
8
If extra drain hose is needed,please
4.
make separate purchase.The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
Page 9
Preparation before washing
Connect the water inlet hose. Open the water faucet.
Confi rm that the washing machine is earthed reliably. Then insert
the power plug into the receptacle. The earth terminal shall not
link to gas pipeline and faucet water pipeline.
Put down the drain hose.
Slanting or uneven ground may result in unstable working or
abnormal noise. Please make the machine stand horizontally.
Pay attention to followings before washing the laundries
Confirm if there is special requirement for the laundries.
Clear the pocket. Take out the coins,sand, hairpins etc.
Tie the long strips; fasten the buttons;close zippers.
The quantity of the laundries shall not be too large. Stretch and loosen the
laundries before putting them in the tub.
When the pulsator is running, the buttons of the laundries may cause noise.
For the sake of discretion, please put the laundries with buttons into other
laundries.
Check if the laundries are applicable for washing with machine.
Please repair the damaged cloth before washing in order to avoid the situation worse.
Divide the laundries that are not colorfast from other laundries.
Put those laundries diffi cult to absorb water into water with hand.
For those laundries with heavy soil, please fi rst remove the dirt like mud or dust. For the parts
with heavy soil, please apply detergent on them in advance, which can make it easier to remove
the soil.
For those laundries that may get lint ball and those with long fur, turn it over before putting in.
Do not put those laundries polluted by chemicals into the washing machine directly.
The foreign materials will result in damage of the machine.
9
Page 10
The capacity of washing and spinning of he machine refer to the largest weight
of the standard laundries under dry condition that can be washed or spinned in one
time. One time washing quantity shall be lower than the rated capacity.
The thickness, size, type of the cloth will infl uence the actual washing capacity. It
is suitable for one time washing to put in reasonable amount of laundries and the
laundries can be turned round in washing.
Do not select the high water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
How to use the washing powder and Softner
Directly dissolved in the machine: (not applicable for fuzzy program )
The instant dissolving of the washing powder:
The super quick program, it is suggested to adopt liquid detergent instead of
washing powder to guarantee the washing effect.
Put in the proper quantities detergent according to the water level and the
laundries quantities.
It is suggested not to use high sudsing
detergent. Washing powder with poor
quality or long time storage maybe caked.
Please pay attention to cleaning the
detergent box in time.
.retaw fo ytitnauq llams lliF .1
.reniatnoc a dna C° 03 fo retaw mraw eraperP .1
.ti evlossid ylluf ot gnirrits elihw redwop eht ddA .2
ti evlossid ot sdnoces 03 rof nuR .redwop eht ddA .2
completely
.level retaw elbatius tceleS .seirdnual eht ni ti tuP .3
How to use the softener
The usage and dose of the softener
as per the specifi cations of softener.
Turn the inner tub,you will find a
softener inlet as the figure 1,open
the cover,put the softener into the
inlet as the figure 2.Before washing,
close the cover and the softener will
drop into the inner tub during the
last time rinsing.
After the softener is put in, please don’t place
for a long time otherwise softener may solidify
and cause flowing not smooth.
Don’t put in the soften if the quick program is
selected.
Open
Figure 1
Access for softener
Close
Figure 2
Control panel seat
Bleach Inlet
How to use the whitener
Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub.
Avoid using whitener on laundries with color or pattern as they are prone to lose color.
The whitener shall not touch the laundries directly.
Refer to the user’s manual for the usage and quantity of the whitener.
For powder whitener, please dissolve it before using.
10
Page 11
Use the operation buttons
Off
On: indicate the program about to run,or indicate
the selected mode or indicate the water level
Flashing: indicate the running program
It displays “- -” during detecting.
It displays total remained time during the
running program (min).
It displays remained reserved time during
reserve program hour
It displays abnormal symbol in abnormal
situation.(See to Page 14)
The digitron displays the time remained
(in minute) before the washing is fi nished.
Push down the reserve but ton. The reserve
indicator light is on the digitron displays the
reserve time of fi nishing washing (in hour).
When the machine is star ted, the reserve
indicator light is on, indicating that the
reserve function is running.
The washing machine can detect the
laundries automatically during After detection,
it will set the water level to suitable value
among 46L 60 L 72L automatically during the
STANDARD program.
The water level decided may be different from
actual value because of the different moisture
level of the laundries.
You can also set water level by yourself. After
the machine is started, it will not set water
level automatically. You shall push the
start/pause button to make new setting.
If there’s water inside the
cannot detect the laundries and will display
water level 60L.If wet laundries are put in, it
may display water level 72L. You must set
suitable water level by yourself.
If quick program is selected, it will display
water level 38L.
If tub dry program is selected, the water
level will not respond.
During operation of wash and rinse program,
you can push down the waterlevel button to
add water. When you release the button, or it
reaches the overfl ow water level, the machine
will stop adding water.
Rinse water level is more first level than
washing (except the highest water level and
hand choosing rinse water level).
tub, the machine
Push the On/Off button to switch on the
power.
When the power is on, push it again to
switch of f the power. Push the
On/Of f button to switch on the power.
If the start/pause button is not pushed, the
washing machine will automatically switch
off the power after 5 minutes.
After the power is switched on,press it to star t
the machine.
During working, push it to pause.
During pause, push this but ton to restart
and go on working
66L 72L
54L 60L
38L 46L
20L 29L
Program Applicable situation
SOAK Washing the relatively big thick or very
STANDARD Common washing
SOFT Washing the woollen textiles
QUICK Posthaste wash of the laundr y under 2.0
WASH Just run the washing cycle with
RINSE Remove the left detergent from the clothes
SPIN When the clothes are washed or the
TUB DRY The purpose is drying the inner tub and
dirty laundries
If “STANDARD” program is set, the
machine will execute fuz zy detection. The
computer will set the water level and wash
time as per the cloth and quantity of the
laundries. The whole procedure is under
automatic control.
kg with light soil.
The water level will automatically set 38L .
drainage cycle. The detergent was left
inside the drum and can be recycled.
and then rinse the clothes
clothes are quite wet, extra spin is needed.
the outer tub, which can avoid growing
out
11
Page 12
1
2
Push “
Push “
After the power is switched on, “SOAK” is automatically set. To select other fully-auto
program, please push the “PROGRAM” button till the corresponding indicator is on.
Refer to the “Program” button on Page 11.
When the “soak” is selected, after the water start to jet, the program wash, rinse and
spin will be implemented (low water level soak for 25 minutes,mid level 35 mins high
level 45 mins)
Push PROGRAM button for 8 times,and it will resume the intial mode.It will circulate
sequence.
Water pressure and water level infl uence the wash time.
Even there’s no water in the tub, the spinning will start after a certain period.
Wash and spin after putting the damageable clothes into tuck net, to avoid scathe.
Wash the laundries that are prone to lose colors separately from other laundries.
When washing start or opening cover intermitting, the washing machine will begin to
work after a period time, this is normal phenomenon.
Only select RINSE program,If there’s water inside the tub, the machine will spin before
rinsing, If there’s no water the machine will rinse directly.
” button to switch on the power
” button to select suitable automatic program
Push “
3
After switching on the power, the washing machine will execute fuzzy program
automatically to detect the cloth during the standard program. After defection, it can set
the water level automatically. To select other water level, fi rst push the “START/PAUSE”
button, then push the “ WATER LEVEL ” button to set the water level.
The pulsator will not rotate unless the water is fi lled to selected water level.
Push “
4
After switching on the power, the reserve program is set to off mode automatically. If you
need to set the washing procedure to be fi nished at reserved time, please push the
“ RESERVE ” button to set the reserve wash program. Refer to reserve button in Page 11
for selection.
” button, select suitable water level
” button to select suitable reserve wash program
Confi rm the operation of reserve program
When the “RESERVE” function is activated, the indicator light of
the program you have set will be off. The “RESERVE (HOURS)” and
“REMAIN MINUTES” indicator lights will be on. During reserve
procedure, push the “RESERVE” button to display the reserve mode.
To change the running program or cancel the reserve setting, you
need to switch off the power and make new selection.
5
Push “ ” button, close the top lid
If the top cover is opened when the machine is spinning, the machine will stop running
and alarm.
Finish washing
6
After Finishing washing, it will switch off power automatically.
12
Page 13
Disposal after washing
Please first pull off the power plug from the receptacle before cleaning.
After using, please clean the lint and foreign materials of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
Clean the detergent box and set it on the control panel seat.
The method of
1
dismantle: Push it up
aslant and gently.
Cleaning the lint filter
Push down the spring
1
piece of the top lint filter
to make the claws out of
the filter cover, and then
pull out the lint fi lter to
get it down.
The method of install :
2
install it upwards and
aslant and push it in.
Pull the back of the lint
2
filter, and then you can
get down it off the front
cover of the lint filter.
Sweep the rubbish in the
lint filter.
Put the back of the lint
filter into the front cover .
Put the lint filter into filter
3 4
cover, and make it tight .
Make sure the lint filter
well installed, or it can
influence your use.
Notes:
The filter screen of the water inlet valve is likely to be blocked by foreign materials and
influence the water inlet. Please clean it with brush every two
months.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
After washing, close the water faucet.
( If needed, you can dismantle the water inlet hose).
Do not store water in the washing machine for a long period.
Drain the water completely after each using.
Be sure to pull off the power plug before maintenance.
Hang up the power cord.
Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid
for some time ( about 1 hour), then close the top lid.
Petrol
Thinner
Alcohol
13
Page 14
14
Trouble-shooting Answer to question
(If there’s breakdown, please pull off the power plug before checking)
The following phenomena are not breakdowns sometimes. Please confirm again before sending it to
repair.
If there are real breakdowns, please come to the special maintenance department or after-sale
service department of our company. Do not repair it by yourself.
Phenomenan The reason How to settle
The digitron displays E0. ●The top lid is opened during
reserve proc edure.
Close the top lid.►
The drainage cannot
work, or is too slow. The
digitron displays E1.
It stops running in
midway. The digitron
displays E2.
The safety switch acts,
and the spinning cannot
work. The digitron
displays E3.
The water filling does
not work, or is slow, the
digital displays E4.
The digitron displays E6. ●The water level sensor is bad. Please contact the after-sales service ►
The
machine
does not
act
There’s abnormal sound
inside the machine
The water tap leaks ●Is the jointer of water inlet hose
Not wash ●Is there power failure?
Not spin ●Is the power plug inserted tightly?
●Is the drain hose blocked?
●Is the drain hose put down?
●The top lid is not closed. Close the top lid.►
e laundries put slantingly?
●Are th
●Is the machine slanting?
●Is the water tap opened, or is
there water supply failure?
●Is the water inlet valve blocked?
●Is the water pressure too low?
●Is the power plug inserted tightly?
●Is the water level reached preset
position?
●Is the top lid closed reliably?
●Are the laundries set flat?
●Is the machine slanting?
●Are the laundries put slantingly in
spinning?
●Are there any foreign materials?
loose or awry?
► Put down the drain hose. Open and
close the top lid once.
► Reorder the laundries and close the
top lid.
►
Clean the foreign mater ial. Open and ►
close The top Lid Once.
Reorder the laundries. Close the top lid.►
The machine will star t running af ter 10 ►
seconds of being plac ed horizontally.
Open the water tap. Push the start /►
Pause button once.
Clean the water inlet valve then push ►
the star t/Pause button once.
Use after the
department.
Please use it when there’s power ►
supply.
Insert the power plug tightly.►
Fill water to the preset position.►
Insert t
Close the top lid.►
Set the laundries flat.►
Adjust the machine to be even. ►
Remove the foreign materials.
Fasten the jointer properly.►
water pressure is normal.►
he power plug tightly.►
Page 15
noitanalpxEanemonehP
The spinning is intermit tent when it starts. Balance the laundries to avoid slanting.
Push the “spin” button to select “Spin”, but it doesn’t
work.
The fi nal spinning is fi nished, it becomes rinsing and
begins to inlet water.
When the power pl
indicator is switched on, and the mac hine star ts
working.
ug is inserted,computer board
The program is setting the drain time. Some time is
needed before it star ts spinning.
Because the washing clothes lean to one side,the
safety switch acts.After water fi lling and running,
eliminating the eccentricity of washing clothes,then
beginning to spin.
It is the special resume function. In the case of power
failure or the power plug is loose during washing, the
machine can save the running program, and resume
the program afterthe power supply is recobered. You
do not need to set the program again
Specifi cation
Rated voltage/Frequency 220-240V ~ /50Hz
Water level / Water quantity (about) 1/20L, 2/29L, 3/38L, 4/46L, 5/54L, 6/60L, 7/66L,8/72L
Injection pressure 0.03 MPa ~ 1.0 MPa
Washing/Spinning capacity 8.5kg/8.5kg
15
Loading...