Haier HWM85-728 User Manual

Fully Automatic Washing Machine

This manual is for
HWM85-728

User's manual

Please read this manual carefully
before using.

Retain it for future reference.

0030508582

CONTENTS

Names of the parts 1

Safety precautions 2

Installation and adjustment 4

Install the water inlet hose 6

Preparation before using 8

Put in the laundries 9

Specification

Water level/Water

quantity (about)

Water Injection pressure

Rated washing /
spinning capacity

1/18L 2/26L 3/34L 4/40L 5/46L
6/52L 7/57L 8/62L 9/66L 10/70L

0.03MPa 1.0MPa

~

Usage of the detergent

9

Use the operation buttons 10

Close the top lid 13

Finish washing 13

Disposal after washing 14

Trouble shooting Answer to question 15

Packing lis 16

Specifcation 17

17

Packing list

×°Ïä˵Ã÷

Names of the parts

Name

User's manual

Warranty card

Water inlet hose

The end connecting to
the washing machine

Bottom plate

Tapping screw

Jointer connecting
the water inlet hose
to the water faucet

The end connecting to
the water inlet hose jointer

Quantity

One piece

One piece

One piece

One piece

Put into the innner tub

One piece

Names of the parts

Top lid component

Detergent box
Control panel seat
Outer tub cover
Lint filter

Balance ring

Inner tub
Filter cover
Pulsator

Control panel film

Cabinet

Base

Adjustable leg

Blenching filler
Screw cover

µ÷Õû½ÅÌù¼þ

Adjustable foot
seam

Meaning and description of the symbols

Warning sign

Contents marked with that symbol are related to the

safety of the product and the personal safety of the users.

Please operate in strict conformity to the contents.

Water inlet valve

Water absorption
cushion

Back control
board

Power cord

Hook

Back cover

Handle

Drain hose

¹Ì¶¨½Å¼þ

Fully automatic washing machine

One set

Forbidden sign

Contents marked with that symbol are actions forbidden

to perform. Performing of those action may result in

damage of the machine or influence the personal safety of

the users.

1

Safety precautions

Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.

Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or the after-sale service department.

In case the washing machine is installed on ground
with carpet, do not block the ventilation hole with
carpet.

The ventilation holes
at the bottom

Carpet

The washing machine must be positioned
so that the plug is accessible. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
cleaning the machine. Do not plug
or pull the power plug with wet hand.

Do not use water hotter than 50 .

Trouble-shooting Answer to question

(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.
Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department
or after-sale service department of our company. Do not repair it by yourself.

Phenomena The reason How to settle

The digitron displays E0.

The drainage cannot work, or is too slow.
The digitron displays E1.

It stops running in midway. The digitron
displays E2.

The safety switch acts, and the
spinning cannot work. The
digitron displays E3.

The water filling does not work, or is
slow. After about 30 minutes later,
the digital displays E4.

The digitron displays E6.

Not wash

The machine does
not act

Not spin

The top lid is opened during reserve procedure.

Is the drain hose put down?
Is the drain hose blocked?

The top lid is not closed.

Are the laundries put slantingly?
Is the machine slanting?

Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?

The water level sensor is bad.

Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?

Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?

Close the top lid.

Put down the drain hose. Open and close the

top lid once.

Clean the foreign material. Open and close the

top lid once.

Close the top lid.

Reorder the laundries. Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.

Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.

Please contact the after-sales
service department.

Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.

Insert the power plug tightly.
Close the top lid.
Set the laundries flat.

2

Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.

Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.

Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.

There's abnormal sound
inside the machine

The water tap leaks

Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?

Is the screw of the jointer of water
inlet hose loose or awry?

Common phenomena

Phenomena Explanation

The spinning is intermittent when it starts.

The wash procedure is paused.

Push the PROGRAM button to select SPIN,
but it doesn't work.

The pulsator pauses during water inlet
in wash and rinse.

There may be some water flowing out of the
drain hose in the first use of the machine.

Balance the laundries to avoid slanting.

The cloth sensor is checking the cloth, it will add water after 48 seconds.

The program is setting the drain time. Some time is needed
before it starts spinning.

It is to avoid splashing during water inlet.

It is the water remained in the factory inspection of performance.

Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.

Fasten the screw of the jointer properly.

Disposal after washing

Safety precautions

After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.

Please first pull off the power plug from the receptacle before cleaning.

Clean the detergent box and set it on
the control panel seat.

1.The method of dismantle: Push it up aslant and gently.

2.The method of install : install it upwards and aslant

Dismantle

Install

The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Please clean it with brush every two months.

The lint filter must be used during washing.

It must be cleaned in time after each using.

Lint filter:

1.Push down the spring piece of the top lint filter
to make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1

2.Pull the back of the lint filter, and then you can
get down it off the front cover of the lint filter. figure2

3.Sweep the rubbish in the lint filter.

4.Put the back of the lint filter into the front cover .

5.Put the lint filter into filter cover, and make it
tight .

6.Make sure the lint filter well installed, or it can
influence your use.

Install

Figure 1

The back cover of lint filter

Up

Dismantle

Dismantle

Down

The front cover of lint filter

Down

Install

Figure 2

If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.

Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing

Do not decompose, repair or alter the machine by
yourself.

machine to avoid them climbing on.

Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.

Up

The handicapped or children without care shall not use
the machine.

Do not wash laundries with volatile materials
(such as thinner, petrol etc.).

trol

Pe

Benzene

Keep the machine away from direct sunlight and
heat source like the heater.

Benzene

1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).

2.Do not store water in the washing machine for a long period. Drain the water completely after each using.

3.Be sure to pull off the power plug before maintenance.

4.Hang up the power cord and drain hose.

5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.

Please keep the lint filter in good condition,
and install it to proper position during
washing. If the lint filter is lost or
damaged, please contact the customer
care agent of our company.

.

Install

Dismantle

To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.

Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.

To change the direction of drain pipe, please contact the customer care agent of our company.
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,

please be sure to ensure the washer is placed under the room temperature for 24 hours and then use
otherwise the washing effects may be lowered or the washer may be damaged.

Installation and adjustment

Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.

Install the bottom plate

After opening the package, please lean the
washing machine gently down on soft items
(like towel cloth,blanket, etc.). Install the bottom

I enlarge

plate to the bottom of the machine with one
screw by a cross screwdriver, then lift the machine
up gently. See to the figure:

The two claws of bottom plate should
insert the two strip holes ,and insure

Adjust the Installation position

The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground
will result in unstable running or stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.

Adjust the adjustable leg:

1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.

2 . After adjustment, fasten the nut.

Loosen

High

Carpet

I

Low

Back

the adjustable nut

Fasten

the adjustable feet

Front

.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The pulsator will not rotate unless the water is
filled to"18L"water level.

The soak procedure can work in cooperation with automatic programs like standard,normal, jeans, and fiber .
There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing,soak and can not
make setting in other cases.

3 Push the button"PROCESS"

You can choose one or more process among soak, wash, rinse, spin.
The button is invaid if you choose QUICK or TUB DRY program.
You can not choose soak process if you choose WOOL program.

WATER

Attention

4 Push the " WATER LEVEL button, select suitable water level"

After switching on the power and the standard normal washing machine will execute fuzzy
program automatically to detect the cloth.After defection, it can set the water level automatically. To select other
water level, first push the "start/pause" button, then push the "water level" button to
set the water level.

5 Push the button and + button

"SELF-PROGRAM" " " " -"

to select suitable program

" "or" "programs set,

LEVEL

M
A
R
G

RO

-P
F

EL
S

Set up time Of soaking, washing, dehydration and times of rinse you can also set up an
appointment; set that means chosen the appointment booking functions, after start,
the light of process you choose will be off, a digital displays the remaining appointment
time (hours). Appointment process, holding down the "self-programming" button to display
the status of an appointment that shows the procedure of your choice, water, process and
the remaining time (minutes). Run the program to change or cancel an appointment,
need to cut off the power supply, re-select. In the light of article 11 can be "self-programming"
button and select button "+""-".

T

E

6 Push the "START/PAUSE" button

R

S
U

TA
S

PA

As the top lid opened, the washer will automatically given alarm and stop running,
exclusively during draining

7 Finish washing

After the laundry process, washing machines beep alarm, and then automatically power off

WATER
LEVEL

After the power is switched on, press it to start the machine
During working, push it to pause.
During pause, push this button to restart and go on working.

REMAIN(MINUTES) indicator digitron

6 START/PAUSE" button"

RESERVE(HOURS)

REMAIN(MINUTES)

During sensing, it displays --
During delay procedure, it displays the remained delay time (in hours).
During operation of programs, it displays the remaining time (in minutes).
In case of abnormal phenomenon, it displays the abnormal symbols

Steps of using the operation buttons and description of each step.

POWER
ON/OFF

1.Push the "POWER ON/OFF " button to switch on the power

It has the special power resume function. In the case of power failure or the power plug is loose
during running , the machine can save the running program, and resume the program after the
power supply is recovered. You do not need to set the program again.

2.Push the "PROGRAM" button to select the suitable
automatic program

After switching on the power, the machine will set STANDARD program automatically. To select other
automatic program, push the "PROGRAM" button till the relative indicator is light . Refer to the
"PROGRAM "button on Page 10 for the selection. For instance: select "QUICK" program for laundries
with small quantity and light soil.

In selecting the standard program, the machine will execute fuzzy program to select water level
and wash time according to the cloth and weight of the laundries. The full process is controlled
automatically.

Page 10

PROGRAM

How to change the direction of the drain hose

1.Loosen the screws of back cover, dismantle the back cover, then take off the drain hose
(As indicated figure 1)

Figure 1

Drain hose
frame

2.Take off the drain hose from base, nip flat the drain hose mouth, dismantle the hang hook, take the
drain hose into cabinet from the left of base As indicated figure 2)

Figure 2

nip flat the drain hose
mouth, dismantle the
hang hook

3.Extend the drain hose from the right side of base, fix the drain hose onto the base with the drain
hose frame, and screw down the screws, put the hang hole onto the drain hose ,then hang up the
drain hose.(As indicated in Figure 3)

Figure 3

4.Install the back cover as primary state.

Remarks: in order to make sure of the correct of installation, it is suggested to change the
direction of the drain hose with our company serviceman .

Usage the drain hose

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall be less than 10cm,

or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.

2.Do not step on or press the drain hose.

4.If extra drain hose is needed, please make separate

purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed

1.5m.

12

Attention

Even there's no water in the tub, the spinning will start
after a certain period.

Wash and spin after putting the damageable clothes
into tuck net, to avoid scathe.

Wash the laundries that are prone to lose colors separately
from other laundries.
When washing start or opening cover intermitting, the washing machine will begin
to work after a period time, this is normal phenomenon.
Only select rinse program,If there's water inside the tub, the machine will spin before
rinsing ,If there's no water the machine will rinse directly.

3. If the drain hose is too long, cut it at mid point. To make

smooth drainage, cut the front end of the hose slantingly.

5.If the extra hose is too long, cut it either at A or at B.

5

Install the water inlet hose

Confirm the water faucet

Water faucet,suitable

Outlet end surface

>10mm

It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.

Water faucet,not suitable

Connection between the water inlet hose jointer and the water faucet

1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the

water inlet hose component. See to Figure 1.

2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)

water inlet hose jointer

Lock level

Slider

Screw knife

Sign plate

Screw

Bushing

PROCESS

SELF-PROGRAM

3 "PROCESS"button

You can choose one or more process among soak, wash, rinse, spin.

The button is invaid if you choose QUICK or TUB DRY program.
You can not choose soak process if you choose WOOL program.

4 button and + button"SELF-PROGRAM" " " " -"

Press the "Self-Program" button, the machine goes into the
self-program state when the associated indicated light
flickers. About 3 seconds later, you can change the program
by pressing "+" or " " button, to adjust reserved time (hour),
soak time (minute), washing time (minute), spinning time
(minute) or rinsing times (number of times) . When the time or
number of times is 0, it means you cancel all the functions the
flicker lights associated with.
When choosing the "quick" program, you can add or reduce
the reserved time. Choosing the "wool" program, you can add
or reduce the reserved time but cannot change the washing,
spinning time and rinsing times, it means the washing time,
spinning time and rinsing times are defaulted time, times or
zero. When choosing the "Tub dry" program, the "Self­Program" and "+" "-" button are invalid.
When choosing the "memory" program, after using the self­program, the washing machine will remember the programs
you set this time when you use it next time.

water inlet hose

3.Fasten the four screws evenly. See to Figure 4.

4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.

remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.

Figure 1

Figure 4

Figure 2

Screw nut

Figure 5

Figure 3

About 4mm before twisting
About less than 2mm after twisting

Figure 6

5 WATER LEVEL button""

During standard programs, the washing machine can detect the laundries automatically. After
detection, it will set the water level to suitable valve automatically among the water level

LOW , MEDIUM , HIGH and

" " " " " " "MAXIMUM".

.

You can also set water level by yourself. After the machine is started, it will not set water level
automatically. You shall push the START/PAUSE button to make new setting.""

WATER
LEVEL

If there's water inside the tub, the machine can not detect the laundries and will display water
level "MEDIUM" .If wet aundries are put in, it may display water level "MAXIMUM" .

If "QUICK" program is selected, it will display water level "LOW". The water level can not
be adjusted.

During operation of wash , rinse and soak program, you can push down the water level
button to add water. When you release the button, or it reaches the overflow water level, the
machine will stop adding water.

The water level decided may be different from actual value because of the different moisture
level of the laundries.

4 Use the operation buttons

RESERVE(HOURS)

REMAIN(MINUTES)

R

S

E
S

O

E
R

A

V

K

E

(M

(H)

SELF-PROGRAM

PROCESS

MEMORY

HEAVY

CHILD

QUICK

PROGRAM

SOAK

WASH

R

W

S

I

A

P

N

S

I

RINSE

S

H

N

E

(M)

SPIN

(T)

(M)

STANDARD

COTTON

WOOL

TUB DRY

66L

57L

46L

34L

18L

WATER
LEVEL

70L

62L

52L

40L

26L

S

T

AR

P

AUS

Connection between the water inlet hose and the washer

1.Do not take off the water absorption cushion. Please check if the

cushion is dropped or damaged before each usage. If it happens

POWER
ON/OFF

T

E

please contact our after-sale department immediately.

2 Put the nut of the water inlet hose on the valve jointer.

3 Fasten the nut. Swing it gently to confirm if it's suitable.

jointer of the
water inlet valve

nut of the water
inlet hose

water absorption
cushion.

Connection between the jointer of the water inlet hose and the water inlet hose

Mode and meaning of the indicators

The light is off

Flashing: indicate the running program or indicate the water level

On: indicate the program about to run, or indicate the selected mode or indicate the water level

1 "POWER ON/OFF"button

POWER
ON/OFF

Push the "POWER ON/OFF"button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "POWER ON/OFF" button to switch on the power. If the "START/PAUSE"button is not pushed, the
machine will switch off the power automatically after 5 minutes.

2 "PROGRAM"button

Applicable situation

Program

STANDARD

Washing the normal laundries

HEAVY Washing the bigger and heavier lanudries

GENTLE

Washing the woolen textiles or underwear

QUICK

PROGRAM

Quick waching of the light dirt laundries

BLANKET

Washing the blanket

COTTON

Washing the cotton textiles
Washing the woollen textiles

WOOL

Drying the inner tub and the outer tub, which can avoid growing mildew.(after washing
clothes,there is dampness between the inner tub and the outer tub, the wall of the inner tub

TUB DRY

and out tub can breed mildew, where you can choose thetub dry program, Drying the inner
tub and the outer tub, keeping the inner tub and outer tub dry, which can avoid growing mildew.

1.Push down the slider. Insert the water inlet hose into the jointer.

Locking level

the jointer of the
water inlet hose

Slider

2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.

Check the connection between the jointer of the water inlet hose
and the water faucet

1.Swing the hose gently to confirm if it is fastened stable.

2.After installation, open the faucet to check if it leaks.

3.Do not bend the hose with overstrain.

4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.

Dismantle the water inlet hose

1. Close the water faucet.

2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.

If the machine is used frequently, the jointer of the water inlet hose can be
kept

on the faucet to prevent damaging the fixing screw.

Locking level

Slider

1 Preparation before washing

2.Put in the laundries

Preparation before washing

1.Connect the water inlet hose

2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.

3.Put down the drain hose

4.slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally

Pay attention to followings before washing the laundries

Confirm if there's
special requirement
for the laundries.

a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
g.For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into
mesh bag for washing.

Clear the pocket.
Take out the coins ,
sand, hairpins etc.

Fasten the buttons
and zippers.

The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.

When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
laundries.

The capacity of washing and spinning of he
machine refer to the largest weight of the standard
laundries under dry condition that can be washed or
spinned in one time.One time washing quantity
shall be lower than the rated capacity.
The thickness, size, type of the cloth will influence
the actual washing capacity. It is suitable for one
time washing to put in reasonable amount of laundries
and the laundries can be turned round in washing.

Do not select high water level for laundries less than

1.0kg ,so as to avoid splashing of water.

3. Usage of the detergent

Control panel seat

Liquid whitener inlet

Ư°×¼Á

Access for detergent

Detergent box

Access for softener

How to use the whitener

Fill water to decided level .Dilute
the whitener with container. Pour it
slowly into the washing tub.
Avoid using whitener on laundries
with colour or pattern as they are

prone to lose colour.
The whitener shall not touch the
laundries directly.

Refer to the user's manual for the

usage and quantity of the whitener.

For powder whitener, please

dissolve it before using.

The usage and dose of the softener as per the specifications
of softener.
Before washing put the softener into the detergent box directly
as indicated in the left figure The softener will be put into the
washer when the last rinsing.
After that,please close the detergent box.Refer to the following
list for the usage of the detergent:selection of the water level,
water quantity and dosage of detergent.
After the softener is put in, please don't place for a long time
otherwise softener may solidify and cause flowing not smooth.

Directly dissolved in the machine (not applicable for
fuzzy program )

1.Fill small quantity of water.

2.Add the powder. Run for 30 seconds to dissolve it
completely.

3.Put in the laundry. Select suitable water level.
The instant dissolving of the washing powder:

1.Prepare warm water of 30 and a container.

2.Add the powder while stirring to fully dissolve it. In
selecting the quick program, it is suggested to adopt
liquid detergent instead of washing powder to
guarantee the washing effect.
Put in the proper quantities detergent according to the
water level and the laundries quantities.
It is suggested not to use high sudsing detergent.
Washing powder with poor quality or long time storage
maybe caked. Please pay attention to cleaning the
detergent box in time.

How to use the softener

How to use the washing powder