Page 1
Page 2
TABLE OF CONTENTS
PAGE
IMPORTANT SAFETY INSTRUCTIONS.............2, 3
OPERATING INSTRUCTIONS....................................4
Parts and Features...........................................................................4
Operating instructions....................................................................5
CARE AND CLEANING GUIDE.......................... .............7
Cleaning and Maintenance ..............................................................7
Moving & Vacationing .. .. .. .. ......................... .. .. .. .. . .. .. ... ........8
TROUBLE SHOOTING..................................... .............8
INSTALLATION INSTRUCTIONS....................... ...........10
Tools and Materials Required.........................................................10
Unpacking Your Washer..................................................................11
Levelling Your Washer.....................................................................11
Steps for Installation......................................................................12
ELECTR ICAL REQUIREMENTS............................ ........ 14
Power Interruptions.......................................................................14
SPECIF ICATIONS.. ........................... .. .. .. .. .. .. .. .Back Cover
1
Page 3
IMPORTANT SAFETY INSTRUCTIONS
Warning - To reduce the risk of fire , electric shock, or
injury when using your appliance, follow basic
precautions, including the following:
1. Rea d all instructions before using the appliance.
2. This appliance is not intended for use by persons (including child ren)
with reduced physical, sensor y or mental capabilities, or lack of
experience and knowle dge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play wi th the appliance.
3. Use t his appliance only for its intended purpose as described in
this user and care guide.
4. Use o nly detergents or softeners recommended for use in this
appliance and keep them out of the reach of childre n.
5. This appliance must be properly installed i n accordance with the
installation instructions before it is used.
6. Never unplug your appliance by pulling on the power cord.
Always grasp the plug firmly and pull straight out from the outlet.
7. Rep lace worn power cords, loose plugs and power outlets
immediately.
8. Unp lug your applia nce before clea ning or before making any
repairs. Repairs should only be done by authorised techn ician..
9. Do no t operate your ap pliance when parts are missin g or broken.
10. Do not tamper with controls.
11. Do not operate your appliance in the presence of exp losive
fumes or toxic flammable vapours.
12. Do not use hot water that exceeds 60 C in temperature. This
refers to hot water entering the machine. I f temperature
cannot be controlled, use WARM wash only.
o
2
Page 4
13. Do not use this appliance to wash clothes w hich are stained,
spotted or washed in gasoli ne , dry cleanin g solvents or any
other explosive or flammable substances that c ould ignite
and explode.
14. Do not add or mix any flammable or explosive substan ces to
the wash.
15. Do not try to remove clothes while the washer is in motion.
Wait until it comes to a complete stop.
16. The lid mu st be closed when the machine is in o peration.
17. Do not use this appliance for commercial applications.
18. Do not operate this appliance unless al l panels are properly intact.
19. The appl iance is not to be used by children without adult su pervision.
20. This app liance must be connected to an approved electrical ou tlet
with 220-240V power source.
21. Do not repair or replace any part of the appliance, t his can only be
done by an authorised technician.
22. To reduce the ris k of electric shock or fire , do not use extension
cords or adapters to connect the unit to electri cal power source.
23.
For washing machines having ventilation openings in the base,
the installation instructions shall state that the openi ngs must
not be obstructed by a carpet.
24.Use the hoses provided.
25. If this ap pliance is supplied from a cord extensio n set or electrical
portab le outlet device, the cord extension set or ele ctrical portable
outlet device must be positioned so that it is not s ubject to splashing
or ingress of moisture.
3
Page 5
Agitator
Page 6
Page 7
Extra Rinse (5)
Press button once to activate.•
Press again to deactivate .•
•
In this option the wash load will go through one extra rinse at the
end of the cycle.
An Extra Rinse will automatically be added to the Whites C ycle .•
Loading the Washer:
When loading the clothes into your washing machine, there are a few points to
remember:
* Separate the white from the colored items. Separate heavily soiled items from
light or delicate items.
* Carefully check all pockets and cuffs for small items.
* Remove pins and other sharp objects from clothing to avoid damages to the
interior parts.
* Pre-treat all stains and heavily soiled areas for better result.
* Load each item loosely. For better results, load smaller items in first, followed
by larger items.
* Do not overload the washer.
* When loading wet items, keep water level high enough so items can float easily
in the water.
* Close the lid after loading the laundry. With the lid open, the washer will not
start.
6
Page 8
Note: Please only use a low-sudsing or high-efficiency type deterg ent.
Bleach use and dispenser :
*
Bleaching of clothes can help remove stains, heavy soiling and kill
bacteria.
*
Bleach should not be used on silk, wool , rayon or drip dry clothes.
*
Bleach dispenser is located on the front corne r under the lid.
*
Fill the dispenser with the manufacturer's recommended dosa ge
during the first water fill.
*
Be careful not to spill undiluted bleach onto the wa sher cabinet or
your clothes.
Note: Use only liquid bleach in dispenser.
CARE AND CLEANING GUIDE
Warning: Always un plug your washer to avoid electric shock before
cleaning. Igno ring this warning may result in injury. Before using cleaning
products, always read and follow manufacturer warnings to avoid
personal Injury or product damage .
Cleaning and Maintenance
* Use only a damp or sudsy cloth for cleaning the control panel.
* To avoid any kind of d amage to cabinet finish, wipe washer cabinet as
needed. If you spill liquid/powdered softener bleach or detergent on the
cabinet, wipe cabinet immediately .
* Do not use any abrasive, harsh chemicals, ammonia, chlorine ble ach,
concentrated detergent, solvents or metal scouring pads. These
chemicals may dissolve, damage and/or discolor your washer.
* Leave lid open after washing to allow inside of washer to dry and assist
in preventing unwe lcomed bad odours.
7
Page 9
Moving & Vacationing
* Turn off water supply at the faucet and disconnect hoses. Drain water
from all hoses.
* Disconnect electrical plu g.
* Dr y inner wash tub. If moving washer disconnect drain h ose.
* Turn the leve ling legs clockwise all the way in.
* Move and store your washer in upright position only.
* To prevent mold or mildew, leave lid open so moisture inside machine
can evaporate .
* Insert t ransporting bolts if you are relocatin g the washer. Ensure
removal pri or to usage.
TROUBLE SHOOTING
If washer does not operate:
* Check the unit is plugged in. The plug may have come loose.
* Check if the electrical wall receptacle is of proper voltage.
* Check if the circ uit breaker needs to be reset or if the fuse needs
replacing.
* Check if the washer is overloaded :load may need to be re-arranged or
redistributed evenly.
* Check if the lid is open. You may have to close the lid properly.
* Th e washer pauses in some cycles. This is normal in delicate o r handwash cycles which has short period of time. You will not hear washer
operation for a short period of time. When the soak time is over, i t will
star t au tomatically.
Problems with water:
* Not enough water coming out: Water faucet may need to be
completely turned on. Hoses may be tangled or kinked. Straighten out
hoses. Check water level selection, it may need to be readjusted.
8
Page 10
* Water temperature is i ncorrect: Check your water heater
temperature. H ot water needs to be at a temperatu re of at least 120 F-
° ° °
140 F(49 C-60 C).Check to make sure the inlet hoses are properly
connected (E.g. Hot to hot & cold to cold).
* Water leaks: This may be due to incorrectiy installed drain hose or fill
hoses. Your home drain may be clogged . You may need to tighten hoses,
check the plumbing or call a plumber for assistance.
* Water will not drain: This may be due to not installing your drain hose
correctly. Check the position of the dra in hose. I n order to drain
properly, make sure t hat top of drain outlet is less than 5 ft. (1.5 m)
above the flo or.
°
Washer is making noise:
* Washer may n eed to be reinstalled (Check washer installation
section).
* Washer load may need to be re-balanced, as the load may be uneven.
* Coins, loose change, but tons or other heavy objects could create
noise related sou nds.
* Squealing sound: Due to overloaded wash tub.
* Vibration Noise: may be caused by not leveling washer properly on the
floor or uneven distribution of clothes in the tub.
Normal Operating Sounds
* Th e following sounds are normally heard during the
operation of the washer:
* Tumbling sounds: This is normal as the heavy wet clothes in
the washer are cont inuously being lossed around.
* Air rushing noise: This happens when the washer tub spins at
very high speeds.
* Wash and Rinse cycles going on and off will also make clicking
sounds.
9
Page 11
Problems with clothes:
*
Clothes become excessively creased: this is due to i mproper sorting,
overloadi ng or washing in excessively hot water repeatedly. Avoid
overloadi ng and resort your load. Wash in cooler water.
*
Soap residu e: deter gent may not be dissolved in water.
*
Check water temperature , add detergent as wash tub is being filled
with water. Reduce deter gent dosage or pre-dissolve detergen t before
adding to wash.
*
Spots or stains on your clothes: this i s due to incorrec t use of fabric
softener. Refer to m anufacturers instructions on the contain er and follow
directions.
*
Clothes are grayed or yellowed: this may b e due to not using
sufficient detergent for large loads. Add more detergent to the load.
*
Clothes are rippe d & have holes/excessive wear & tear: this may be
due to sharp objects left in washing. Remove all small loose sharp
objects, fasten belts, z ippers, metal snaps etc. Check if you are usi ng
undiluted bleach. Never add undiluted bleach to wash .
LED Display Notes:
Trouble Codes
Rinse and spin indicators flash
All progre ss in dic ato rs fl ash
All load size (water level ) i ndi cat ors
flash
“Small” and “E xtr a Sma ll” l oad s ize
(water leve l) in dic ato rs fl ash
“Super” and “L arg e”lo ad si ze
(water leve l) in dic ato rs fl ash
Beeps
Unit does not drain, or th e spe ed of d rai nin g is to o slow.
The washer is out of balance. Plea se op en th e lid
and reba lan ce th e loa d.
The water inlet time exceeds the pre set t ime .
Water ove rfl ow protection.
The water level se nso r fau lt - Ca ll se rvice .
Top lid n ot cl ose p roperly.
Reaso ns
INSTALLATION INSTRUCTIONS
Tools and Materials Required
You will need to have following tools to help you
with the installation of your washer:
Pliers, Wrench,Tape Measure,Gloves, Level
10
Page 12
Accessories Supplied
1.Hot & Cold inlet hoses
2.Drain Hose Hook
3.Pipe Clip/brace
4.Outer Drain Hose
1
2
Quantity
2
1
1
1
3
4
Unpacking Your Washer：
*
Remove all pa cking materials. This includes the foam base and all
adhesive tape holding the washer accessories inside and outside.
*
Open the top lid to rem ove the drum brace. Pull to remove.
NOTE: Save drum brace. Reinstall when moving the wa sher.
*
Inspect and remove any remains of packing, tape or printed materials
before usin g the washer.
WARNING: To avoid danger of suffocation, keep plastic bag and other
packing material away from babies and children. Do not use this bag in
cribs,carriages and playpens. The plastic bag could bl ock nose and mouth
and prevent breath ing. This bag is not a toy.
Leveling Your Washer
*
Your washer has 4 leveling legs; which are located on the four bottom
corners.
*
After properly placing your wa sher in its final position, you can level
your washer.
*
Levelin g legs can be adjusted by turning them counterclockwise to
raise your washer o r turning them clockwise to lower your washer.
Adjustable foot
High Low
WARNING:Leveling of washe r is very important to prevent vibration
during spin.
11
Page 13
Steps for Installation
• Select a suitable location for the washer on a hard even surfac e away
from direct sunlight or heat source e.g. radiators, baseboard heaters,
cooking appliances et c. Any floor unevenness should be corrected with
the level ing legs located on the bottom corners of the washer. The
washer must be placed at room temperature. You must not place washer
where the tempera ture is at below freezing.
For this machine having ventilation openings in the base, make sure the
openings must not be obstructed by a carpet.
Installing Your Washer
Read installation instructions carefully before installation.
1. Do no t use water inlet hoses without a flat washer on each end. The
washer in the coupling has to be placed firmly. Flat water inlet hose
washers are preinstalled in each end of the water inlet hoses.
New hose-sets supplied with the appliance are to be used and that old
hose-sets should not be reused.
NOTE: You may have to use pliers to tighten the coupling.
Do not over tig hten because you may cause damage to the valve.
Cold water inlet hose
Hot water inlet hose
2. Con nect the hot and cold water inlet hoses to the hot and cold water
faucet.
12
Page 14
3. Ins tall the drain hose to the back of the washer using the drain hose
clamp provided. The drain hose must be placed into a drain pipe or sink
at least 3.5cm in diameter. Use the goose neck to fix the h ose in place .
To avoid possible flus h back of water, the drain hose must be fixed at a
minimum height of 1000m m and a maximum height of 1500mm.
Water Inlet
Goose Neck
Water Supply Hose
Hose Bend
Drain Hose
4.Plug the wash er into a regular 220-24 0Volt/ 50Hz,10Amp outl et.
Note :Car efully insp ect ar ou nd the machine fo r any leaks, and ti gh ten an y
loose connecti ons.
Caution: If, after completing these steps, you are unsure that unit is
properly installed, contact a qualified installer. To ensure
that your washer is properly installed, it is recommended
that it be installed by a cer tified installer.
13
Page 15
ELECTRICAL REQUIREMENTS
Earthing Instructions
This appliance mu st be grounded. In the event of an electrical
shor t ci rcuit, grounding reduces the risk of electric shock by
providi ng an escape wire for the electric current. This appliance
is equipped with a grounding wire with a grounded plug. The
plug must be inserted into an outlet that is properly installed
and grounded.
Improper use of t he plug can result in a risk of electric shock.
Consult a qualified electrician or service person if the
grounding ins tructions are not completely understood or i f
doubt exists as to whether the appliance is properly grounded.
Wiring Requirements:
The washer must be plugged into at least 10AMP 220-240 VOLT,
50 HZ GROUNDED OUTLET.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
Note: If a standard two-prong
outlet is encountered, it is the
personal responsibility and
obligation of the consumer
to have it replaced with a
properly grounded
three-prong outlet.
Extension Cords:
We do n o t r e c o mmend t h at y o u u s e an extensio n cord .
CAUTION: If this appliance is supplied from a cord extension set or
electrical portable outlet device, the cord extension set or electrical
portable outlet device must be positioned so that it is not subject to
splashing or ingress of moisture.
Power Interruptions
Occasionally there may be power interruptions due to
thunderstorms or other causes. Remove the power cord from AC
outlet when a power outage occurs. When power has been
restored re-plug power cord to AC outlet. If outage is for a
prolonged per iod, cle an washer before using it again.
14
Page 16
SPECIFICATIONS
Rated voltage·frequency 220-240V~ · 50Hz
Rated washing / spinning capacity
Spin speed max
Inlet pressure 0.03MPa-1.0MPa
Net weight
Dimensions (mm)
7.5kg/7.5kg
650rpm
59kg
686( Depth) x 686(Width)
x 1105(Height)
15
Loading...