Haier HWM75-0528 A User Manual

Download

Page 1

Fully Automatic Washing Machine

This manual is for HWM75-0528 A

User's manual

Special number: 837A

Please read this manual carefully before using. Retain it for future reference.

Page 2

CONTENTS

Specification table the 2nd cover

Names of the parts 1

Safety precautions 2

Installation and adjustment 4

Install the water inlet hose 6

Preparation before washing 8

Put in the laundries 8

Usage of the detergent

Close the top lid 9

Use the operation buttons 10

Finish washing 13

Disposal after washing 14

Trouble-shooting answer to question 15

Packing list 16

Specification table

Water level

Water quantity (about)

Water Injection pressure

Largest rated washing / spinning capacity

1/18L 2/24L 3/28L 4/32L 5/35L 6/38L 7/42L 8/46L 9/50L 10/52L

0.03MPa 1MPa

7.0kg

Page 3

Packing list

Names of the parts

User's manual

Warranty card

Components of the water inlet hose

Lint filter

Tapping screws

Bottom plate

Automatic washing machine

One

Eight

One

Inside the document bag

Inside the accessory bag

Inside the document bag

Inside the accessory bag

Between the upper cushion of the washing machine package and the upper seal of the package carton

Top lid component

Detergent box

Control pannel

Filter frame Softener inlet

Balance ring Inner tub

Pulsater

Front control board

Cabinet

Fixed leg

(3 pieces)

Adjustable leg

Adjustable leg film

Water inlet valve

Water absorption

cushion

Power cord

Meaning and description of the symbols

Warning sign

Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents, otherwise it may cause damage of the machine or injure the personal safety of the user.

Handle

Drain hose

Drain hose frame

Back cover

Forbidden sign

Contents marked with that symbol are actions forbidden to

perform. Performing of those actions may result in damage

of the machine or injure the personal safety of the user.

Page 4

Safety precautions

Please plug thepower plug on special receptacle. Be sure to use three-pins power receptacle. Ensure that the earthing prong of the power receptacle is earthed reliably. Use leakage protector if possible.

Earth

Do not bend ,extend,twist,bind by force.Do not press or nip it with weight. Keep the pin of the power plug clean,if the power plug is polluted with dust, please wipe with dry cloth carefully. If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by the technicians of our special shop or our customer care agent.

In case the washing machine is installed on ground with carpet, do not block the ventilation hole with carpet.

The ventilation

Back

Front

holes at the bottom

Soft object

Do not put the machine at damp place like the bathroom. Never wash it with water. Do not put wet laundries on the control panel.

The washing machine must be positioned so that the plug is accessible. Be sure to pull the plug off and close the water faucet in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine. Do not plug or pull the power plug with wet hand.

Do not use water hotter than 50 .

Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations in spinning.

Trouble-shooting answer to question

(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.

Phenomena The reason How to settle

Buzzing upon reservation starts, the digitron displays "E0"

No or slow drain,

displays

Running pauses during spin,

the digitron displays

buzzing

Safety switch actuates, not spin, (after self-correction

the digitron displays

twice),

"E3",

buzzing

No or slow water filling (not reaching the level in 40 min),

the digitron displays

buzzing

The digitron displays E6.

Poor or no waterfall flow

The machine does not act

There's abnormal soundinside the machine

The water faucet leaks

"E1"

the digitron

,buzzing.

"E2",

"E4",

Not wash

Not spin

The top lid is not closed

Is the drain hose put down?

Is the drain hose blocked by foreign material?

The top cover leaves open

Are the laundries put slantingly?

Is the machine slanting?

The water tapis not open The water inlet valve is blocked

The water pressure is too low and the current is too small

The water level sensor is bad.

If the nozzle is choked with foreign bodies

Is there power failure?

Is the power plug loose? Does the water level arrive at the set water level?

Is the power plug loose?

Is the top lid closed?

Are the laundries put orderly?

Is the machine slanting?

Are the laundries slanting in spinning?

Is the jointer screw of the water inlet hose is loose or twisted awry?

Close the top lid

Put down the drain hose. Open and close thetop lid once. Clean the foreign material. Open and close the top lid once.

Close the top lid

Re-order the laundries. Close the top lid.Level the machine in right position. Open and close the top lid once.

Open the water tap. Push the "Start/Pause" button. Clean the water inlet valve. Push the "Start/Pause" button. Wait forthe normal water pressure Before use.

Please contact the after-sales service department.

Remove the foreign bodies

Use it when the power is on.

Insert the power plug tightly.

Affusion to the set water level.

Insert the power plug tightly.

Close the top lid

Put the laundries orderly.

Level the machineproperly. Re-order the laundries.

Fasten the jointer screw properly.

Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more.

Common phenomena

Phenomena

The spinning is intermittent when it starts.

The wash procedure pauses.

Select spin program, but it does not work.

There may be some water flowing out of the drain hose in the first use of the machine.

Explanation

Balance the laundries to avoid slanting.

The cloth sensor is detecting , it will add water after about 48 senconds.

The program is setting the drain time , certain period is needed before it starts spinning.

It is the water remained performance inspection by the factory.

Page 5

Disposal after washing

Safety precautions

After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning.

The lint filter must be used during washing. It must be cleaned in time after each using.

1. Take off the lint filter Put hand at the indicated position. Push down to take it off. ( See to Figure 1)

2. Clean the lint Put it in water and clean while it is

Figure 1

still wet.(See to Figure 2)

3. Install the lint filter After cleaning, insert the bottom of the lint filter ( marked with

Figure 2

"down side") into the filter frame , then push the upper part of the filter in ( marked with " up side "). (See to Figure 3)

The filter screen of the water inlet valve is likely to be blocked by foreign materials and influence the water inlet. Please clean it

If the cabinet is dirty, wipe it with wet cloth

Do not flush it directly with water.

Wipe it with neutral detergent.

Figure 3

Do not wipe it with thinner, petrol,

alcoholetc.

hol

Alco

Thinner

Petrol

Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children.

Do not put any hot or heavy items (such as the kettle with hot water) on the washing machine

The appliance is not instruct for use of young children of infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.

Do not decompose, repair or alter the machine by yourself.

Do not wash laundries with volatile materials (such as thinner, petrol etc.).

Benzene

Keep the machine away from direct sunlight and heat source like the heater.

1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).

2.Do not store water in the washing machine for a long period. Drain the water completely after each using.

3.Be sure to pull off the power plug before maintenance.

4.Hang up the power cord and drain hose.

5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (about 1 hour), then close the top lid.

Page 6

Installation and adjustment

Please install and adjust the machine according to the requirement of the mannual. It is very important to your security and correct operating the machine.

Install the lint filter

1.Press downward to assemble.

2.Pull upward to detach.

Install the bottom plate

After you open the package, please lean the washing machine gently down on soft items ( like the towel cloth,blanket, etc. ). Install the bottom plate to the bottom of the machine with the eight screws by a cross screwdriver, then lift the machine up gently. See to the figure:

Back

Front

Soft items

Screw

Bottom plate

Adjust the Installation position

The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in unstable running or stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal: Hang the lead line to check if it is horizontal.

3 Push the " WATER LEVEL "button,select suitable water level

After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth. After defection, it can set the water level automatically. To select other water level, first push the "start/pause" button, then push the "water level" button to set the water level.

4 Push the "PROGRAM/RESERVE" button to select suitable reserve wash program

After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing procedure to be finished at reserved time, please push the "PROGRAM/RESERVE" button to set the reserve wash program two seconds. Refer to "PROGRAM/RESERVE" button in Page 11 for selection.

the washing will be finished after 18 hours.

5 Push the "Start/Pause" button

6 Finish washing

Adjust the adjustable leg:

1 .To twist the adjustable leg, please first lift up the side of the leg slightly, loosen the adjustable nut, and twist the leg.

2 . After adjustment, fasten the nut.

Loosen

High

Low

Fasten

After finishing wash it will switch off power automatically

the adjustable nut

the adjustable leg

Page 7

Steps of using the operation buttons and

Digitaldisplay

Fuzzy logic control

10 waterlevel selection

Digitaldisplay

Fuzzy logic control

10 waterlevel selection

Digitaldisplay

Fuzzy logic control

10 waterlevel selection

Digitaldisplay

Fuzzy logic control

10 waterlevel selection

description of the steps

Program

STANDARD

SOAK HEAVY GENTLE SAVE COTTON

INDICATIONOF PROCESS

SINGLE WASH

RINSE SPIN SINGLESPIN

TUB CLEAN AIRDRY

(NO CHOOSING)

SOAK WASH RINSE SPIN

START PAUS E

TIMEREMAINED(MINUTES)

RESERVE(HOURS LATER)

PROGRAM/RESERVE

1.Push "POWER"button to switch on the power

2.Push "PROGRAM/RESERVE" button to select suitable automatic program

IGH

WATER

Digitaldisplay

LEVEL

Fuzzy logic control

10 waterlevel selection

POWER ON/OFF

PROGRAM/RESERVE

POWER ON/OFF

How to change the direction of the drain hose

1.Dismantle the rear cover of the washing machine.

2.Put down the drain hose .Take off the drain hose frame as indicated in Figure 1.Take the drain hose into the cabinet ,then nip the drain fixing clamp to make it deviated from the clip,the other hand is used to put down the drain bushing,as indicated in Figure 2,3.

Drain hose

Drain bushing

Take down

Figure 3

Drain bushing

Figure 2

Figure 1

Drain hose support

Cabinet

Inner

Outer

Push

Drain hose fixing clamp

Push

Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose with our company serviceman .

3.Dismantle the drain outlet protecting cover at the other side, (the way is the same as the drain bushing),then install the drain bushing, as indicated in Figure 4.

4.Extend the drain hose from the other side. Fix the drain hose with drain hose frame onto the cabinet, as indicated in Figure 5.

Drain outlet protecting cover

Figure 4

Drain bushing

5.Install the drain outlet protecting cover to the other side, as indicated in Figure 6

Usage the drain hose

Figure 5

Figure 6

After the power is switched on, "standard" is automatically set. To select other full-auto program, please push

the "PROGRAM/RESERVE" button till the corresponding indicator is on. Refer to the "PROGRAM/RESERVE

button" on Page 11.E.g

For instance:select "SAVE" program for small quantity of laundries with light soil.

Program select

The display of digitron

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall be less than 10cm,

or the drainage will not be smooth, and cost such long time that the machine may stop at mid way.

2.Do not step on or press the drain hose.

Program

STANDARD Common washing

SOAK HEAVY

GENTLE

SAVE

COTTON

SINGLE WASH

RINSE SPIN

SINGLE SPIN

TUB CLEAN

AIR DRY

Application

Washing for coverlet bigger laundries

Washing the woollen silk textiles

Washing for normal laundries

Washing the cotton textiles

Reusing the washing detergent

Washing the cloth washed by hand (first draining, then spinning)

Only spinning the cloth wet or washed by hand (first draining, then spinning)

The spinning time is the same to the single spin, but spinning in lower

Avoid growing mildew on the outer tub and the inner tub

The running process (the digitron displays the running process)

WASH( )

RINSE( )

SOAK( )

WASH( )

RINSE( )

WASH( )

RINSE( )

WASH( )

RINSE( )

SPIN( )

RINSE( )

SPIN( )

3. If the drain hose is too long, cut it at mid point. To make

smooth drainage, cut the front end of the hose slantingly.

4.If extra drain hose is needed, please make separate

purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed

1.5m.

5.If the extra hose is too long, cut it either at A or at B.

Page 8

Install the water inlet hose

Digital display

Fuzzy logic control

10 water level selection

Digital display

Fuzzy logic control

10 water level selection

Digital display

Fuzzy logic control

10 water level selection

Digital display

Fuzzy logic control

10 water level selection

Confirm the water faucet

Water faucet,suitable

Outlet end surface

It is required that the front end shall be longer than 10mm. The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.

Water faucet,not suitable

Connection between the water inlet hose jointer and the water faucet

1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the

water inlet hose component. See to Figure 1.

2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise it may leak water. See to Figure 3.)

water inlet hose jointer

Sign plate

Screw

Bushing

Figure 3

About 4mm before twisting

About less than 2mm after twisting

Figure 6

Slider

Figure 1

Screw knife

Figure 2

Lock level

water inlet hose

3.Fasten the four screws evenly. See to Figure 4.

4.Take off the nameplate. Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet. See to Figure 5.

remark: Before installation, the threading is 4mmabove the upper surface of the nut.

After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.

Screw nut

Figure 4

Figure 5

Reserve,Process,remain time digitron

It displays "--" during detecting. It displays remained reserve time (hour). It displays total remained time (min). If the total time exceeds 99 minutes, it uses "A" on tens digit to represent100 minutes, and uses "b" to represent 110 minutes.E.g. "A3" represents 103 minutes. It displays abnormal symbol in abnormal situation. (See to Page15)

LIG

(MINUTES)

(HOURS LATER)

FLASH

PROGRAM/RESERVE

PROGRAM/RESERVE button

Push down the program/ reserve button. You can select one program of ten which is standard,soak heavy, gentle,save,cotton, single wash,rinse spin,single spin,tub clean, air dry;

Push the"program/ reserve" button to set the reserve wash program morethan two seconds continuously; When the "reserve" function is activated, the indicator light of the program you have set will be off. The "reserve (hour)" and "time remain" indicator lights will be on; During reserve procedure, push the "reserve" button to display the reserve mode.To change the running program or cancel the reserve setting, you need to switch off the power and make new selection;

"Power" button

Push the "power" button to switch on the power. Under power-on mode, push it to switch off the power. Push the "power" button to switch on the power. If the "start/pause" button is not pushed, the machine will switch off the power automatically after 5 minutes.

POWER

WATER

LEVEL

Digital display

Fuzzy logic control

10 water level selection

ON/OFF

WATER LEVEL button

The washing machine can detect the laundries automatically. After detection,it will set the water level to suitable value among 4, 6, 8,and 10 automatically.

You can also set water level by yourself. After the machine is started, it will not set water level automatically. You shall push thestart/pause button to make new setting.

If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .

If save program is selected, it will display water level 2 . When water level 2 is reached in water filling, it will perform washing while filling water.When water level 3 is reached, it will change to normal washing.

During operation of wash and rinse program, you can push down the water level button to add water. When you release the button, or it reaches the overflow water level, the machine will stop adding water.

The water level decided may be different from actual value because of the different moisture level of the laundries.

Attention As selecting the water level 1,3,5,7,9;the light

is flashing; As selecting the water level 2,4,6,8,10;the light is lighting;

Page 9

5 Use the operation buttons

Connection between the water inlet hose and the washer

Description of operation button

Indicator mode and meaning

Off:

Flashing: indicate the running program

On: indicate the program about to run, or indicate the selected mode

Program

Attention:

he digitron displays the remained time and process alternately during the washing machine

1. T

working.

2. The process function is not selected solely .(see to Page 12)

STANDARD

SOAK HEAVY

GENTLE

SAVE

COTTON

SINGLE WASH

RINSE SPIN

SINGLE SPIN

TUB CLEAN

AIR DRY

INDICATIONOF PROCESS (NO CHOOSING)

SOAK WASH RINSE SPIN

START PAU SE

START/PAUSE button

After the power is switched on,press it to start the machine During working,push it to pause. During pause,push this button to restart and go on working

TIME REMAINED

RESERVE

1.Do not take off the water absorption cushion. Please check if the

cushion is dropped or damaged before each usage. If it happens please contact our after-sale department immediately.

nut of the water inlet hose

2 Put the nut of the water inlet hose on the valve jointer.

3 Fasten the nut. Swing it gently to confirm if it's suitable.

jointer of the water inlet valve

water absorption cushion.

Connection between the jointer of the water inlet hose and the water inlet hose

the jointer of the

1.Push down the slider. Insert the water inlet hose into the jointer.

2 Hang the lock lever to the jointer. Release the slider till a click

Locking level

water inlet hose

Slider

sound is heard.

Check the connection between the jointer of the water inlet hose and the water faucet

1.Swing the hose gently to confirm if it is fastened stable.

2.After installation, open the faucet to check if it leaks.

3.Do not bend the hose with overstrain.

4.Before each usage please check if the connection between the jointer of the water inlet hose and the water faucet, and the installation of the water inlet hose are firm, so as to prevent dropping from improper installation position.

Dismantle the water inlet hose

1. Close the water faucet.

2. Press the locking lever. Push down the slider. Then pull of the water inlet hose.

If the machine is used frequently, the jointer of the water inlet hose can be

on the faucet to prevent damaging the fixing screw.

kept

Locking level

Slider

Page 10

1.Preparation before washing

3. Usage of the detergent

Preparation before washing

1.Connect the water inlet hose

2.Confirm that the washing machine is earthed reliably.Then insert the power plug into the receptacle.Do not connect the earth terminal to the gas pipe and tap water pipe.

3.Put down the drain hose.

4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally.

Pay attention to followings before washing the laundries

Confirm if there's special requirement for the laundries.

a. Check if the laundries are applicable for washing with machine. b. Divide the laundries with unfast color from other laundries. c. Put those laundries difficult to absorb water into water with hand. d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil, please apply detergent in advance, which can make it easier to remove the soil. e. For those laundries that may get lint ball and those with long fur, turn it over before putting in. f. Do not put those laundries polluted by chemicals directly into the washing machine. For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into mesh bag for washing.

Clear the pocket. Take out the coins , sand,hairpins etc.

Fasten the buttons and zippers.

The quantity of the laundries shall not exceed the rated value. The big laundries like the jeans shall be put in loosely.

When the pulsator is running ,the buttons of the laundries may cause noise. For the sake of discretion ,please put the laundries with buttons into other laundries.

2.Put in the laundries

The capacity of washing of the machine refer to the largest weight of the standard laundries under dry condition that can be washed in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.

The thickness ,size , type of the cloth will influence the actual washing capacity. It is suitable to put inreasonable amount of laundries and the laundries can be turned round in washing for one time washing.

Do not select more than "4" water level for laundries less than 1.0kg ,so as to avoid splashing of water.

How to use the softner

The usage and dose of the softener as per the specifications of softener.

SOFTNER

Softener

inlet

Before washing put the softener into the filling entrance(can be found on the balancing ring by rotating the inner tub, as illustrated in the left drawing, The softener will put into the washer when rinsing. After the softener is put in, please don't place for a long time otherwise softener may solidify and cause flowing not smooth. When the washer in spin process,please don't push "START/ PAUSE " button for fear that the softener is put in earlier, which affect the effects.

Control panel seat

Add washing powder into the box directly

as per indicated in left figure.

After adding, close the box.

Liquid detergent inlet

How to use washing powder

How to use the whitener

Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Avoid using whitener on laundries with color or pattern as they are prone to lose color. The whitener shall not touch the laundries directly. Refer to the user's manual for the usage and quantity of the whitener. For powder whitener, please dissolve it before use.

It is suggested to add washing powder into the box directly under fuzzy program and reserve program. Dissolve directly inside the washing machine: (not applicable

for fuzzy and reserve program)

1.Add some water(select the "1" water level)

2.Add washing powder. Run for about 30s to fully dissolve the powder. Then push the"start/pause" button.

3.Put in laundries. Select suitable water level. Push the

"start/pause"

Quick dissolving of washing powder:

1.Prepare warm water of 30 C and container.

2. Add washing powder while stirring to dissolve it completely.

Please add suitable washing powder as per the laundries quantity, the set water level and water quantity.

If you select save program, it is suggested to use liquid detergent instead of washing powder to guarantee the washing effect.

It is not recommended to use rich-foam washing powder.

Washing powder with poor quality or long-time storage may get caked. Please clean the detergent box duly in usage.

button again.

4. Close the top lid

If you open the top lid,the machine will stop working and alarm in spinning process.

Haier HWM75-0528 A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual