Page 1
User’s Manual
Fully Automatic Washing Machine
This manual is for
HWM70-918NZP
Please read this manual carefully before using.
Retain it for future reference.
Index
Safety precautions ...............2
Packing list ...........................4
Names of the parts ...............4
Installation and
adjustment............................5
Preparation before
washing................................9
Use the operation buttons ....
11
13
15
16
0030809432
Disposal after washing .......
Trouble-shooting Answer
to question..........................
Specification .......................
Page 2
2
Safety precautions
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
Forbidden sign
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
Warning sign
Meaning and description of the symbols
Please check if the power receptacle has good earthing condition before using to guarantee
your safety.
Please check if the water faucet is open, and if the connection of the water inlet pipe is
proper.
It is suggested to use foamless washing powder.
Please don’t use the washer in the environment below 0 °C; if the washer has been stored
below 0°C, please be sure to ensure the washer is placed under the room temperature
for 2~4 hours and then use otherwise the washing effects may be lowered or the
washer may be damaged.
Please insert the power cord into special receptacle with rated voltage.
Be sure to use single-phase three pins receptacle.The earthing terminal of
the receptacle must be earthed reliably. If possible,please adopt electric
leakage protector.
The washing machine must be positioned so that the plug is accessible. Be
sure to pull the plug off and close the water faucet in following cases: power
failure, delivering the machine, setting the machine idle or cleaning the
machine.
Do not plug or pull the power plug with wet hand.
Do not bend ,extend, twist, bind or alter the power cord by force. Do not press
or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacles
loose, do not use the plug any more.
Page 3
3
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole
with carpet.
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not put wet
laundries on the control panel.
Do not wash water-proof laundries like the raincoat,
bike covers etc. to avoid abnormal vibrations
in spinning. Wash the clothes that can float
on the water sur face easily, please be careful
especially,for fear damage.
Do not stretch hands into the working machine. It is
dangerous even if the rotation is slow. Take special
care of the children.
Do not put any hot or heavy items (such as the
kettle with hot water ) on the washing machine.
Do not wash laundries with volatile materials (such
as thinner, petrol etc.)
The children shall not approach the working
washing machine.
Keep the machine away from direct sunlight and
heat source like the heater.
Do not decompose, repair or alter the machine by
yourself.
Do not use water hotter than 50 °C.
Page 4
4
Names of the parts
Packing list
Fully automatic
washing machine
Water inlet hose Bottom plate Tapping screws
(One Package)
User’s manual
Warranty card
All illustrations in this Manual are
given for reference only. Your
products and accessories may
show differences from these
illustrations due to our continuous
improvement.
Back cover
Power line
Drain hose
Water inlet valve
Water absorption cushion
Back control board
Screw cover(left)
Control panel seat
Top lid component
Filter cover(2 pieces)
Control panel film
Cabinet
Adjustable foot
Outer tub cover
Lint filter(2 pieces)
Balance ring
Inner tub
Fixed foot(3 pieces)
Detergent box
Pulsator
Front control board
Adjustable foot film
Screw cover(right)
Liquid whitener inlet
Page 5
5
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important
to your security and correct operating the machine.
1. Move the control handle of trundle to
the point 1 and the control handle fix on
the second reference column; Then insert
the base panel from the side and fix it in
the suitable site which aim to the hool of bolt.
2.Caste hit the control handle position
shown in the figure ,the control handle
will be fixed by the frist reference
columns to install the screw into the
bottom of the washing machine with
a screwdriver,then gently propped.
The control handle of trundle
Adjust the adjustable foot:
To twist the adjustable foot, please fi rst lift up the side of the leg slightly, loosen the
adjustable nut, and twist the foot. Please make sure to keep the washing machine
in balance.
1.
After adjustment, fasten the nut.
The adjustable foot
2.
The washing machine away from wall should be overrun 20mm. The largest allowable slope
of the shank base of the machine is 2°. The slanting or rough ground will result in unstable
running or stoppage of the machine. Please adjust it with following methods:
CarpetCarpet
Back
Front
Adjustable foot
Bottom plate
Screw
Confirm
it's horizontal:
Hang the lead line to check if it is horizontal.
The frist reference colunm
Pullback spring
Figure 1 Figure 2
The operation of trundle
The second
reference colunm
Page 6
6
Screw knife
Figure 4
Figure 5
About 4mm before twisting
About less than 2mm after twisting
Screw
Bus hi ng
Sig n p la te
Scr ew nu t
Figure 2
Figure 3
Figure 6
2.Loosen the screw till the water faucet can be
accessed. Put the jointer of the water inlet
hose on the faucet. See to Figure 2. (If the
faucet is too large and the jointer can not be
set on the water faucet,please loosen the four
screws and take out the bushing in the jointer.
The front end of the faucet must be smooth,
otherwise it may leak water .See to Figure 3.)
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut
as per the indication of the figure to seal up the
exit end face of the faucet. See to Figure 5.
Remark: Before installation, the threading is
4mm above the upper surface of the nut.After
installation, the threading is 2mm above the
upper surface of the nut.See to Figure 6.
Connection between the water inlet hose jointer and the
water faucet
1.Press the lower end of the lock lever and push
down the slider. Take off the water inlet hose
jointer from the water inlet hose component.
See to Figure 1.
water inlet hose jointer
water inlet hose
Figure 1
Slider
Lock lever
The exit end face of the faucet
water faucet, suitable
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth.If not please file it to avoid leakage.
Confirm the water faucet
water faucet, not suitable
Page 7
1.Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each usage. If it happens please contact our
after-sale department immediately.
2.Put the nut of the water inlet hose on the valve
jointer.
3.Fasten the nut. Swing it gently to confirm if it's
suitable.
1.Push down the slider. Insert the water inlet hose
into the jointer.
2.Hang the lock lever to the jointer. Release the
slider till a click sound is heard.
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection between
the jointer of the water inlet hose and the water faucet, and
the installation of the water inlet hose are firm, so as to
prevent dropping from improper installation position.
1.Close the water faucet.
2. Press the locking lever. Push down the slider.Then pull off the water inlet hose.
If the machine is used frequently, the jointer of the water inlet hose can be kept
on the faucet to prevent damaging the fixing screw.
Dismantle the water inlet hose
Connection between the jointer of the water inlet hose and the
water inlet hose
Check the connection between the jointer of the water inlet hose
and the water faucet
Locking lever
Slider
wat er abs orpti on
cus hion
nut of the water
inl et hos e
The jointer of the
water inlet hose
Slider
Locking lever
joi nter o f the
wat er inl et val ve
Connection between the water inlet hose and the washer
7
The new hose-sets supplied with the appliance are to be used and
that old hose-sets should not be reused.
Page 8
8
The drain hose shall drain smoothly.
Do not trample or press the drain hose.2The height of the drain hose shall be less
than 10cm , or the drainage will not be smooth,
and cost such long time that the machine may
stop at mid way.
1
3
5
4
If the drain hose is too long, cut it at mid
point. To make smooth drainage,cut the front
end of the hose slantingly.
If the extra hose is too long,cut it either at A or at B point.
If extra drain hose is needed,please
make separate purchase.The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
How to change the direction of the drain hose
Figure 2
Figure 3
Back cover
Figure 1
Up claws
Screws
Figure 4
Down claws
Two sides claws
Drain hose rack
Screws
1. Dismount the back cover of the
washing machine.
2. Put down the drain hose. Take off
the drain hose hook. Then take off the
screws of the drain hose rack.
Put the drain hose into the cabinet.
(As indicated in Figure 2).
3. Extend the drain hose from the other
side, then fix the screw of the drain hose
rack, fix the drain hose hook and hang
the drain hose on the cabinet.
(As indicatedin Figure 3).
4. Install the back cover, first put the
down claws on the cabinet, and then
put the claws(marked with )into the
cabinet from down to up, and fix the
screws. (As indicated in Figure 4)
Page 9
9
Preparation before washing
Connect the water inlet hose. Open the water faucet.
Confi rm that the washing machine is earthed reliably. Then insert
the power plug into the receptacle. The earth terminal shall not
link to gas pipeline and faucet water pipeline.
Put down the drain hose.
Slanting or uneven ground may result in unstable working or
abnormal noise. Please make the machine stand horizontally.
Clear the pocket. Take out the coins,sand, hairpins etc.
Confirm if there is special requirement for the laundries.
Check if the laundries are applicable for washing with machine.
Please repair the damaged cloth before washing in order to avoid the situation worse.
Divide the laundries that are not colorfast from other laundries.
Put those laundries dif fi cult to absorb water into water with hand.
For those laundries with heavy soil, please fi rst remove the dirt like mud or dust. For the parts
with heav y soil, please apply detergent on them in advance, which can make it easier to remove
the soil.
For those laundries that may get lint ball and those with long fur, turn it over before putting in.
Do not put those laundries polluted by chemicals into the washing machine directly.
The foreign materials will result in damage of the machine.
The quantity of the laundries shall not be too large. Stretch and loosen the
laundries before putting them in the tub.
When the pulsator is running, the buttons of the laundries may cause noise.
For the sake of discretion, please put the laundries with buttons into other
laundries.
Tie the long strips; fasten the buttons;close zippers.
Pay attention to followings before washing the laundries
Page 10
10
How to use the whitener
How to use the washing powder
How to use the softener
Fill water to decided level. Dilute the whitener with
container. Pour it slowly into the washing tub.
Avoid using whitener on laundries with color or
pattern as they are prone to lose color.
The whitener shall not touch the laundries directly.
Refer to the user’s manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before using.
Directly dissolved in the machine: (not applicable for fuzzy program )
.retaw fo ytitnauq llams lliF .1
.yletelpmoc ti evlossid ot sdnoces 03 rof nuR .redwop eht ddA .2
.level retaw elbatius tceleS .seirdnual eht ni tuP .3
The instant dissolving of the washing powder:
.reniatnoc a dna C° 03 fo retaw mraw eraperP .1
.ti evlossid ylluf ot gnirrits elihw redwop eht ddA .2
If you select the quick program, it is suggested to adopt
liquid detergent instead of washing powder to guarantee
the washing ef fect.
Put in the proper quantities detergent according to the
water level and the laundries quantities.
It is suggested not to use high sudsing detergent. Washing
powder with poor quality or long time storage maybe caked.
Please pay attention to cleaning the detergent box in time.
The usage and dose of the softener as per the specifi cations of softener.
Turn the inner tub,you will find a softener inlet as the figure 1,open the
cover,put the softener into the inlet as the figure 2.Before washing,close
the cover and the softener will drop into the inner tub during the last time
rinsing.
After the softener is put in,please don’t place for a long time otherwise
softener may solidify and cause flowing not smooth.
The capacity of washing and spinning of the machine refer to the largest weight
of the standard laundries under dry condition that can be washed or spinned in one
time. One time washing quantity shall be lower than the rated capacity.
The thickness, size, type of the cloth will infl uence the actual washing capacity. It
is suitable for one time washing to put in reasonable amount of laundries and the
laundries can be turned round in washing.
Do not select high water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
Figure 1
Figure 2
Open
Close
Access for detergent
Access for softener
Control panel seat
Liquid whitener inlet
Washing powder box
Page 11
Use the operation buttons
Off
On: indicate the program about to run,or indicate
the selected mode or indicate the water level
Flashing: indicate the running program
During sensing, it displays “--” .
During delay procedure, it displays the
remained delay time (in hours).
During operation of programs,it displays the
remaining time (in minutes).
In case of abnormal phenomenon, it displays
the abnormal symbols (see to Page 15 ).
Memory
Standard
Wool
Tub Dry
Program
Normal
Strong
Soft
Quick
Wash
Overflow
SpinRinse Delay
During Memory,Strong,Soft,Normal and Standard
program you can adjust the value of them.
For Wool you can select procedure , but can not
change them.
The digitron displays the time remained (in minutes)
before the washing is finished.
Push the “Delay” but ton, the digitron displaysthe delay
time of washing (in hours).The indicator flashes to
indicate that the delay function is operating.
Push the “Delay” button to display the delay mode.
Program Applic able situation
Normal
Strong
Soft
Quick
Memory
Washing the normal laundries
Washing the bigger and heavier laundries
Washing the woollen textiles or underwear
Washing the laundries with small quantity
and light soil
The common wash, the washer will set to
Custom program including wash, rinse,
spin and water level automatically last time
Standard
Wool
Tub Dry
Washing the normal laundries with less water
Washing the woollen textiles
Drying the inner tub and the outer tub,
which can avoid growing mildew
Push the “Power” but ton to
switch on the power.
When the power is on, push it again to
switch of f the power.
Push the “Power” but ton to
switch on the power.If the “
Start/Pause
button is not pushed, the washing machine
will automatically switch off the power
after 5 minutes.
After the power is switched on,press it to star t
the machine.
During working, push it to pause.
During pause, push this button to restart
and go on wor king .
Remaining
Time
Delay Time
47L
38L
30L
22L
14L
Water
level
52L
43L
34L
26L
18L
1st Rinse
2nd Rinse
3rd Rinse
Reserve
Water
Power
Start/Pause
You can choose “Reserve Water” to keep water.
It will keep the after rinsing water once finish rinsing
in tub about 4 hours ,and buzzer every 15 minutes .
Press “Start/Pause” button or open and close the top
one time to collect the after rinsing water ,or else it
will drain automatically,then go on for next program .
The washing machine can detect the laundries
automatically after detection, it will set the water
level to suitable value among level 26L,34L,43L,
52L automatically during the Normal,Memory
and Standard program.
You can also set water level by yourself.After the
machine is started, it will not set water level
automatically. You shall push the “Start/Pause”
button to make new setting.
If there’s water inside the tub, the machine can
not detect the laundr ies and will display water
level 34L .If wet laundries are put in, it may
display water level 52L .You must set suitable
water level by yourself.
If Quick program is selected, it will display
level 22L, the water level can be adjusted.
water
If Tub Dry program is selected, the water level
will not respond.
During operation of wash , rinse and soak
program, you can push down the water level
button to add water. When you release the
button, or it reaches the overflow water level,
the machine will stop adding water.
The water level decided may be dif ferent from
actual value because of the different moisture
level of the laundries.
”
11
Page 12
12
Push the “ ” button to
switch on the power
Push the “
” button to select suitable automatic program
It has the special power resume function. In the case of power failure or the power plug is
loose during running, the machine can save the running program, and resume the program
after the power supply is recovered. You do not need to set the program again.
1
2
Program
After the power is switched on, “Memory” is automatically set. To select other full-auto
programs, please push the “Program” button till the corresponding indicator is on. Refer to
the “Program” button on Page 11.
E.g. Set to “Quick”program for small quantity of laundries with light soil.
When a standard cycle is selected, the fuzzy program is run. The water level and the washing
time can be selected according to be texture and volume of the laundry. The washing cycle is
automatically controlled.
Even there’s no water in the tub, a certain period is required before spin starting.
Separate the laundries that are not colorfast from other laundries in washing.
After the machine starts operation, you can only set the program and procedure during
washing and soaking,
During rinsing ,you can only set the spinning time, and can not make setting in other cases.
During Quick, Tub Dry programs, push the Wash, Rinse,Spin button the machine has
no reaction.
For Standard program, the washing machine will execute fuzzy program automatically to detect
the cloth. After defection, it can set the water level automatically.To select other water level, first
push the “Start/Pause” button, then push the “Water Level” button to set the water level.
Push “ ” “
” “
” button to select suitable
Push the “ ” button, select suitable water level
3
procedure program
W
ate
r
level
Water
Reserve
If you choose “1st Rinse” and ”2nd Rinse” together ,the machine will keep the after first and second
rinsing water .
Push the “ ” button, select suitable reserve water times
4
5
Page 13
13
Push the “
” button to select suitable delay wash program
After switching on the power, the delay time program is set to off mode automatically. If you
need to set the washing procedure to be finished at delay time, please push the “DELAY”
button to set the delay wash program. Refer to delay button in Page 11 for selection.
Confirm the operation of “Delay” program
When the “ Delay” function is activated, the indicator light of
the program you have set will be off. The “Delay Time” and
“Remaining Time” indicator lights will be on. During delay
procedure, push the “Delay” button to display the delay time
mode.
To change the running program or cancel the delay time setting,
you need to switch off the power and make new selection.
6
Push the “
” button,close the top lid
7
If the top lid is opened when the machine is spinning, the machine will stop running and alarm.
Finish washing
8
After finishing washing, the washing machine will cut off the power automatically.
Disposal after washing
Please first pull off the power plug from the receptacle before cleaning.
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise
it may influence your using the machine.
Clean the detergent box and set it on the control panel seat:
1 2
The method of dismantle: Push it up
aslant and gently.
The method of install : install it upwards and
aslant and push it in.
Page 14
14
1
2
3
4
Cleaning the lint filter:
Push down the spring piece at the top of the lint filter to make the claws out of the filter cover,
and then pull out the lint filter to get it down.(figure 1)
Put the lint filter into filter cover, and make it tight .
Make sure the lint filter well installed, or it can influence your use.
Pull the back cover of the lint filter, and then you can get down it off the front cover of the
lint filter.(figure 2) Sweep the rubbish in the lint filter.Put the back cover of the lint filter into
the front cover .
Filter cover
Lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
Figure 1
Figure 2
Notes:
The filter screen of the water inlet valve is likely to be blocked by foreign materials and
influence the water inlet. Please clean it with brush every two
months.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
After washing, close the water faucet.
( If needed, you can dismantle the water inlet hose).
Do not store water in the washing machine for a long period.
Drain the water completely after each using.
Be sure to pull of f the power plug before maintenance.
Hang up the power cord and drain hose.
Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid
for some time ( about 1 hour), then close the top lid.
Page 15
15
Trouble-shooting Answer to question
Phenomena The reason How to settle
The digitron displays E0. The top lid is open during
reserve procedure.
Close the top lid.
The drainage cannot
work, or is too slow. The
digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and
Clean the foreign material. Open and
close the top lid once.
close the top lid once.
It stops running in
midway. The digitron
displays E2.
The top lid is not closed. Close the top lid.
The safety switch acts,
and the spinning cannot
work. The digitron
displays E3.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
Place the machine horizontally, open
and close the top lid once.
The water filling does
not work, or is slow, the
digitron displays E4.
Is the water tap opened, or is
there water supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
Open the water tap. Open and close the
top lid once.
Clean the water inlet valve then open
and close the top lid once.
Use after the water pressure is normal.
The digitron displays E6. The water level sensor is bad. Please contact the after-sales service
department.
The
machine
does not
act
Not wash Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset
position?
Please use it when there’s power
supply.
Insert the power plug tightly.
Fill water to the preset position.
Not spin
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
The water tap leaks
There is abnormal sound
inside the machine
Is the screw of the jointer of water
inlet hose loose or awry?
Is t he mac hine slanting?
Are the laundries put slantingly in
spinning?
Are there any foreign materials?
Fasten the screw of the jointer properly.
Adjust the machine to be even
Reorder the laundries and close the top
lid.
Remove the foreign materials.
(If there’s breakdown, please pull of f the power plug before checking)
The following phenomenon are not breakdowns sometimes. Please confirm again before sending it to
repair.
If there are real breakdowns, please come to the special maintenance department or after-sale
service depar tment of our company. Do not repair it by yourself.
Page 16
Specifi cation
Injection pressure 0.001 MPa —1.0 MPa
Washing / Spinning capacity
7.0kg/7.0kg
Phenomena Explanation
The spinning is inter mittent when it starts. Balance the laundries to avoid slanting.
Push the “spin” button to select “Spin”, but it doesn’t
work.
The program is setting the drain time. Some time is
needed before it starts spinning.
There may be some water flowing out of the drain hose
in the first use of the machine.
The wash procedure is paused.
It is the water remained in the factory inspection of
performance.
The cloth sensor is checking the cloth, it will add
water after 48 seconds.
The pulsator pauses during water inlet in wash
and rinse.
It is to avoid splashing during water inlet.
When the power plug is inserted,computer board
indicator is switched on, and the machine star ts
working.
It is the special resume function. In the case of power
failure or the power plug is loose during washing, the
machine c an save the running program, and resume
the program after the power supply is recovered. You
do not need to set the program again.
Loading...