Haier HWM70-0528T User Manual

Fully Automatic Washing Machine

This manual is for
HWM70-0528T

User's manual

Special number: 0030807098A

Please read this manual
carefully before using.
Retain it for future reference.

CONTENTS

Specification table the 2nd cover

Names of the parts 1

Safety precautions 2

Installation and adjustment 4

Install the water inlet hose 6

Preparation before washing 8

Put in the laundries 9

Usage of the detergent

Close the top lid 9

Use the operation buttons 10

Finish washing 13

Disposal after washing 14

Trouble-shooting answer to question 15

Packing list 16

9

Specification table

Water level

Water quantity (about)

Water Injection pressure

Standard rated washing /
spinning capacity

Largest rated washing /
spinning capacity

1/18L 2/24L 3/28L 4/32L 5/35L
6/38L 7/42L 8/46L 9/50L 10/52L

0.03MPa 0.78MPa

~

5.0kg

7.0kg

Packing list

User's manual

Warranty card

Components of the water inlet
hose

Lint filter

One

One

One

One

Inside the document bag

Inside the document bag

Inside the accessory bag

Inside the document bag

Names of the parts

Top lid component

Detergent box

Control pannel

Lint filter

Balance ring

Inner tub

Pulsater

Front control
board

Cabinet

Fixed leg

(3 pieces)

Adjustable leg

Adjustable
leg film

Water absorption

cushion

Power cord

Water inlet valve

Handle

Drain hose

Drain hose frame

Back cover

Tapping screws

Bottom plate

Automatic washing machine

Eight

One

One

Inside the accessory bag

Between the upper cushion of the washing
machine package and the upper seal of the
package carton

Meaning and description of the symbols

Warning sign

Forbidden sign

Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.

Contents marked with that symbol are actions forbidden to

perform. Performing of those actions may result in damage

of the machine or injure the personal safety of the user.

1

Safety precautions

Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.

Earth

Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or our customer care agent.

In case the washing machine is installed on ground
with carpet, do not block the ventilation hole with
carpet.

The ventilation

Back

Front

holes at the bottom

Soft object

Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.

The washing machine must be positioned so that
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.

Do not use water hotter than 50 .

Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.

Trouble-shooting answer to question

(If there's breakdown, please pull off the power plug before checking) The following phenomena are not
breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.

Phenomena The reason How to settle

Buzzing upon reservation starts,
the digitron displays "E0"

No or slow drain,

displays

Running pauses during spin,

the digitron displays

buzzing

Safety switch actuates, not
spin, (after self-correction
twice),

the digitron displays

"E3",

buzzing

No or slow water filling (not
reaching the level in 30 min),

the digitron displays

buzzing

The digitron displays E6.

Poor or no waterfall flow

The machine does
not act

There's abnormal soundinside the
machine

The water faucet leaks

"E1"

the digitron

, buzzing.

"E2",

"E4",

Not wash

Not spin

The top lid is not closed

Is the drain hose put down?

Is the drain hose blocked by
foreign material?

The top cover leaves open

Are the laundries put slantingly?

Is the machine slanting?

The water tapis not open
The water inlet valve is blocked

The water pressure is too low
and the current is too small

The water level sensor is bad.

If the nozzle is choked with
foreign bodies

Is there power failure?

Is the power plug loose?
Does the water level arrive at the
set water level?

Is the power plug loose?

Is the top lid closed?

Are the laundries put orderly?

Is the machine slanting?

Are the laundries slanting in
spinning?

Is the jointer screw of the water
inlet hose is loose or twisted
awry?

Close the top lid

Put down the drain hose. Open
and close thetop lid once.
Clean the foreign material.
Open and close the top lid once.

Close the top lid

Re-order the laundries. Close the
top lid.Level the machine in right
position.
Open and close the top lid once.

Open the water tap.
Push the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait forthe normal water pressure
Before use.

Please contact the after-sales
service department.

Remove the foreign bodies

Use it when the power is on.

Insert the power plug tightly.

Affusion to the set water level.

Insert the power plug tightly.

Close the top lid

Put the laundries orderly.

Level the machineproperly.
Re-order the laundries.

Fasten the jointer screw
properly.

Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.

2

Common phenomena

Phenomena

The spinning is intermittent when it starts.

The wash procedure pauses.

Select spin program, but it does not work.

There may be some water flowing out of the
drain hose in the first use of the machine.

Explanation

Balance the laundries to avoid slanting.

The cloth sensor is detecting , it will add water
after about 48 senconds.

The program is setting the drain time , certain
period is needed before it starts spinning.

It is the water remained performance inspection
by the factory.

Disposal after washing

Safety precautions

After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.

Please first pull off the power plug from the receptacle before cleaning.

Clean the detergent box and set it on
the control panel seat.

Dismantle Install

The filter screen of the water inlet valve is
likely to be blocked by foreign materials
and influence the water inlet. Please clean
it with brush every two months.

The lint filter must be used during washing.
It must be cleaned in time after each using
Lint filter:

1.Pull it up to dismantle.

2.Push it down to install.

3.Clean the filter screen after washing.

Dismantle Install

Clean

If the cabinet is dirty, wipe it with wet cloth

Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol,
alcohol etc.

ol

etr

P

hinner

T

Alcohol

Do not stretch hands into the working machine.
It is dangerous even if the rotation is slow.
Take special care of the children.

Do not put any hot or heavy items (such as the kettle
with hot water) on the washing machine

The appliance is not instruct for use of young
children of infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.

Do not decompose, repair or alter the machine
by yourself.

Do not wash laundries with volatile materials
(such as thinner, petrol etc.).

Benzene

Keep the machine away from direct sunlight and
heat source like the heater.

1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).

2.Do not store water in the washing machine for a long period. Drain the water completely after
each using.

3.Be sure to pull off the power plug before maintenance.

4.Hang up the power cord and drain hose.

5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for
some time (about 1 hour), then close the top lid.

Installation and adjustment

Please install and adjust the machine according to the requirement of the mannual.
It is very important to your security and correct operating the machine.

Install the bottom plate

After you open the package, please lean the
washing machine gently down on soft items ( like
the towel cloth, blanket, etc. ). Install the bottom
plate to the bottom of the machine with the eight
screws by across screwdriver, then lift the machine up
gently.See to the figure:

Back

Front

Soft items

Screw

Bottom plate

Adjust the Installation position

The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.

Adjust the adjustable leg:

1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.

2 . After adjustment, fasten the nut.

Loosen

High

Low

Fasten

the adjustable nut

the adjustable leg

3 Push the " WATER LEVEL "button,select suitable water level

After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level.

4 Push the "PROGRAM/RESERVE" button to select suitable reserve
wash program

After switching on the power, the reserve program is not set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the "PROGRAM/RESERVE"
button to set the reserve wash program two seconds. Refer to "PROGRAM/RESERVE"
button in Page 11 for selection.

5 Push the "Start/Pause" button

6 Finish washing

After finishing wash it will switch off power automatically

Steps of using the operation buttons and

HWM70-0528T

b

description of the steps

P

ROGRA

M

S

T

A

NDARD

SOA

KHEAVY

GE

NTL

E

SA

V

E

COT

T

SING

T

AI

SI

NGLE WA S

RINS

UB

R

DRY

ON

ESPIN
LE S

CLE

I

NDICAT

I

O

H

N

(

O

NO CHOOSING

FPROCE

SS

)

S

PIN

OAK

WA

A

S

N

H

RI

NSE

S

PIN

START
PAUS E

TIME REMAINED(M INUTES)

RESERVE(HOURSLATER)

PROGRAM/RESERVE

HT

LIG

H

S

FLA

WATER

LEVEL

1.Push "POWER"button to switch on the power

2.Push "PROGRAM/RESERVE" button to select
suitable automatic program

After the power is switched on, "standard" is automatically set. To select other full-auto program, please push

the "PROGRAM/RESERVE" button till the corresponding indicator is on. Refer to the "PROGRAM/RESERVE

button" on Page 11.E.g

For instance:select "SAVE" program for small quantity of laundries with light soil.

Program select

The display of digitron

01

02

03

04

05

06

07

08

09

10

Program

STANDARD Common washing

SOAK HEAVY

SINGLE WASH

RINSE SPIN

SINGLE SPIN

TUB CLEAN

Washing for coverlet bigger laundries

GENTLE

COTTON

AIR DRY

Washing the woollen silk textiles

SAVE

Washing for normal laundries

Washing the cotton textiles

Reusing the washing detergent

Washing the cloth washed by hand
(first draining, then spinning)

Only spinning the cloth wet or washed by
hand (first draining, then spinning)

The spinning time is the same to the single spin,
but spinning in lower

Avoid growing mildew on the outer tub and the
inner tub

Application

The running process
(the digitron displays the running process)

WASH( )

RINSE( )

SOAK( )

WASH( )

WASH( )

RINSE( )

WASH( )

WASH( )

RINSE( )

SPIN( )

SPIN( )

SPIN( )

RINSE( )

RINSE( )

SPIN( )

WASH( )

HWM70-0528T

POWER
ON/OFF

POWER
ON/OFF

PROGRAM/RESERVE

SPIN( )

RINSE( )

SPIN( )

SPIN( )

SPIN( )

SPIN( )

How to change the direction of the drain hose

1.Dismantle the rear cover of the washing machine.

2.Put down the drain hose .Take off the drain hose
frame as indicated in Figure 1.Take the drain hose into
the cabinet ,then nip the drain fixing clamp to make it
deviated from the clip,the other hand is used to put down
the drain bushing,as indicated in Figure 2,3.

Drain hose

Drain bushing

Take down

Figure 3

Drain bushing

Figure 2

Figure 1

Drain hose support

Cabinet

Inner

Outer

Push

Drain hose fixing
clamp

Push

Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose
with our company serviceman .

3.Dismantle the drain outlet protecting cover at the other side,
(the way is the same as the drain bushing),then install the drain
bushing, as indicated in Figure 4.

4.Extend the drain hose from the other side. Fix the drain hose
with drain hose frame onto the cabinet, as indicated in Figure 5.

Drain outlet
protecting cover

Figure 4

Drain bushing

5.Install the drain outlet protecting cover to the other side,
as indicated in Figure 6

Usage the drain hose

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall be less than 10cm,

or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.

2.Do not step on or press the drain hose.

3. If the drain hose is too long, cut it at mid point. To make

smooth drainage, cut the front end of the hose slantingly.

4.If extra drain hose is needed, please make separate

purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed

1.5m.

5.If the extra hose is too long, cut it either at A or at B.

Figure 5

Figure 6

12

5

HWM70-0528T

TIME REMAINED(M INUTES)

RESERVE(HOURSLATER)

Reserve,Process,remain time digitron

It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes.E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)

HT

LIG

H

AS

FL

WATER

LEVEL

PROGRAM/RESERVE

"Power" button

Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If the
"start/pause" button is not pushed, the machine will
switch off the power automatically after 5 minutes.

HWM70-0528T

POWER
ON/OFF

PROGRAM/RESERVE button

Push down the "program/ reserve" button. You
can select one program of ten which is
standard,soak heavy, gentle,save,cotton,
single wash,rinse spin,single spin,tub clean,
air dry;

Push the"program/ reserve" button to set the
reserve wash program morethan two seconds
continuously;
When the "reserve" function is activated, the
indicator light of the program you have set
will be off. The "reserve (hour)" and "time
remain" indicator lights will be on;
During reserve procedure, push the "reserve"
button to display the reserve mode.To change
the running program or cancel the reserve
setting, you need to switch off the power
and make new selection;

WATER LEVEL button

The washing machine can detect the laundries automatically.
After detection,it will set the water level to suitable value among
4, 6, 8,and 10 automatically.

You can also set water level by yourself. After the machine is
started, it will not set water level automatically. You shall push the

"start/pause" button to make new setting.

If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .

If save program is selected, it will display water level 2 .
When water level 2 is reached in water filling, it will perform
washing while filling water.When water level 3 is reached, it will
change to normal washing.

During operation of wash and rinse program, you can push down
the

"water level" button to add water. When you release the button, or

it reaches the overflow water level, the machine will stop adding
water.

The water level decided may be different from actual value because
of the different moisture level of the laundries.

Attention As selecting the water level 1,3,5,7,9;the light

is Flashing;
As selecting the water level 2,4,6,8,10;the light
is lighting;

PROGRAM

S

SOAK HEAVY

GE

SAVE

COTTO

SIN

GLE

RI

NSE SPIN

SIN

GLE SPIN

T

UB CLEAN

AI

R

DRY

TANDAR

D

N

T

LE

N

WASH

INDICATI O

(NO CHOOSING)

SOAK

WASH

R

INSE

SPIN

START/PAUSE button

After the power is switched on,press it to
start the machine
During working,push it to pause.
During pause,push this button to restart and
go on working

NOF PROCESS

START
PAU SE

TIME REMAINED(M INUTES)

RESERVE(HOURSLATER)

1.Preparation before washing

2.Put in the laundries