Page 1
Fully Automatic Washing Machine
This manual is for
HWM6802
User's manual
Please read this manual
carefully before using.
Retain it for future reference.
Special number: 06274A00305
Page 2
Contents
Specifications.....................................................................................the 2ndcover
Names of the parts................................................................................................1
Safety precautions .............................................................................................2
Installation and adjustment ...................................................................................4
Preparation before washing .................................................................................8
Put in the laundries ..............................................................................................9
Usage of the detergent ........................................................................................9
Use the operation buttons ..................................................................................10
Close the top lid .................................................................................................13
Finish washing ....................................................................................................13
Disposal after washing .......................................................................................14
Trouble shooting Answer to questions.............................................................15
Packing list .........................................................................................................16
Specification
Water level/Water
quantity (about)
Water inlet pressure
Largest washing / spinning
capacity(kg)
HIGH/48L MEDIUM/37L
LOW/30L VERY LOW/20L
0.03MPa-1.0MPa
6.5/6.5
Page 3
Packing list
Name
User's manual
Guarantee
Components of the water inlet
hose
the end connecting to the washing machine
jointer connecting the water
inlet hose and the water faucet
the end connecting to the water
inlet hose jointer
Bottom plate
Tapping screws
Quantity
One
One
One
One
Seven
Storage position
Inside the document bag
Inside the document bag
Inside the accessory bag
Between the upper cushion of the
washing machine package and the
upper seal of the package carton
Inside the document bag
Water valve
Top lid B
Lint filter
Control panel
Filter cover
Inner tub
Pulsator
Control panel
film
Cabinet
Top lid A
Notice label
Detergent box
Hanging hole
for the drain
hose
Power cord
Adjustable foot
stick
ack cover
Adjustable foot
Meaning and description of the symbols
Water absorption
cushion
Handle
Drain hose
Fixed foot (3)
Automatic washing machine
One
16
1
Page 4
Safety precautions
Please plug the plug on special 220-240V
AC receptacle.Be sure to use single-phase
three pins receptacle.Ensurethe earthing
prong of the power receptacle is earthed
reliably.Use leakage protector if possible.
Do not damage the power cord,bend ,extend,twist,bind or alter it by force.Do not press or
nip it with weight.If the supply cord is damaged,it must be replaced by the manufacturer
or its service agent or a similarly qualified person in
order to avoid a hazard. Keep the pin of the power
plug clean,if the power plug is polluted with
dust,pleasewipe with dry cloth carefully.
Do not put the machine at damp place like
the bathroom. Never wash it with water.
Not put wet laundries on the control panel.
For washing machine with ventilation
openings in the base, that a carpet
must not obstruct the openings.
The ventilation holes
at the bottom
soft items
The power cord plug should be convenient
to be pluged in or pluged out with hand
while the washing machine runs normally.
Be sure to pull the plug out and close the
water tap when the machine is idle,when
moving the machine,or when cleaning
the machine.Do not use wet hand to insert or pull out the power plug.
Do not use water hotter above 65 C .
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Trouble shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending it to
repair. If there are real breakdowns, please come to the special maintenance department or
after-sale service department of our company. Do not repair it by yourself.
Phenomena The reason How to settle
Buzzing upon reservation starts,
Nixie tube indicates "E0"
No or slow drain, nixie tube
indicates
Running pauses during spin,
nixie tube indicates
buzzing
"E1"
, buzzing.
"E2",
Safety switch actuates, not
spin, (after self-correction
twice), nixie tube displays
"E3",
buzzing
The water filling does not work,
or is slow,nixie tube indicates
"E4", buzzing
Poor or no waterfall flow
The machine does
not act
There's abnormal sound inside the
machine
The water faucet leaks
Not wash
Not spin
The top lid is not closed
Is the drain hose put down?
Is the drain hose blocked by
foreign material?
The top cover leaves open
Are the laundries put slantingly?
Is the machine slanting?
The water tap is not open
The water inlet valve is blocked
The water pressure is too
low and the current is
too small
If the nozzle is choked with
foreign bodies
Is there power failure?
Is the power plug loose?
Does the water level arrive at the
set water level?
Is the power plug loose?
Is the top lid closed?
Are the laundries put orderly?
Is the machine slanting?
Are the laundries slanting in
spinning?
Is the jointer screw of the water
inlet hose is loose or twisted
awry?
Close the top lid
Put down the drain hose. Open
and close the top lid once.
Clean the foreign material.
Open and close the top lid once.
Close the top lid
Re-order the laundries. Close the
top lid.Level the machine in right
position.
Open and close the top lid once.
Open the water tap. Push
the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait for the normal water pressure
Before use.
Remove the foreign bodies
Use it when the power is on.
Insert the power plug tightly.
Affusion to the set water level.
Insert the power plug tightly.
Close the top lid
Put the laundries orderly.
Level the machine properly.
Re-order the laundries.
Fasten the jointer screw
properly.
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose,
do not use the plug any more.
2
15
Page 5
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during washing.
It must be cleaned in time after each using.
Lint filter:
1.Push down the spring piece of the top lint filter to
make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can get
down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it tight .
6.Make sure the lint filter well installed, or it can
influence your use.
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Please clean it with brush every two months.
Install
Figure 1
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
The back cover of lint filter
Up
Dismantle
Dismantle
Down
The front cover of lint filter
Down
Figure 2
Install
Do not stretch hands into the working
machine. It is dangerous even if the
Do not decompose, repair or alter the
machine by yourself.
rotation is slow. Take special care of
the children.Do not let the children
climb the washing machine.
Up
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
washing machine.
Petrol
Thinner
Petrol
Benzene
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
14
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
Page 6
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
3 Press the "WATER LEVEL" button to select suitable
water level
WATERLEVEL
Install the bottom plate
After you open the package, please lean the washing machine gently down
on soft items ( like the towel cloth,blanket, etc. ). Install the bottom plate to
the bottom of themachine with the screws by a crossscrewdriver,
then lift the machine up gently.See to the figure:
Back
Front
Soft items
Screw
Bottom plate
Adjust the installation position
The largest allowed slope of the
shank base of the machine is 2 .
The slanting or rough ground will
result in unstable running or
stoppage of the machine. Please
adjust it with following methods:
Adjust the adjustable foot:
1.To twist the adjustable foot, please
first lift up the side of the foot slightly,
loosen the adjustable nut, and twist
the foot.
2.Fasten the nut after adjustment.
Loosen
High
Low
adjustable nut
Fasten
adjustable foot
After switching on the power, press the button "WATER LEVEL" to select a water level according
to the load. Please refer to the button " Water level" on page 10.
Page 10
4 Push the " " button
to select suitable reserve program
After switching on, the washing machine reserved wash program will be automatically set
inactive. If you desire a wash cycle to end at a reserved time, you can press the
""
PROGRAM/RESERVE
Refer to The button of
Confirm the reserve program
When"Reserve"becomes active, the nixie tube
displays the time to the end of the reserved wash cycle, and
the indicator turns on.
To change the running program or cancel the reservation,
you should cut off the supply and reselect.
5 Press the "start/pause" button
PROGRAM/RESERVE
button over 2 seconds to set a reserved wash program.
""
PROGRAM/RESERVE
on page 10.
Page 10
the washing will finish
about 18 hours later
START
PAUSE
PROGRAM
RESERVE
START
PAUSE
Close the top lid
During spinning, if the top cover is opened, the washing machine will stop running
and alarm
Finish washing
4
The washing machine cuts off the power supply
automatically when wash cycle ends.
13
Page 7
Install the water inlet hose
Confirm the water tap
Water tap,suitable
Outlet end surface
Water tap,not suitable
Use the operation buttons
b.
Operating procedure and explanations for the
buttons
>10mm
It is required that the front end shall be longer than 10mm.
The outlet end surface of the tap shall be flat and smooth. If not please file it to
avoid leakage.
Connection between the water inlet hose jointer and
the water tap
1.Use the new water inlet hose provided with the machine to connect to the water
faucet.Old hose sets should not be reused.
2.Press the lower end of the lock lever and push down the slider. Take off the water
inlet hose jointer from the water inlet hose component. See to Figure 1.
3.Loosen the screw till the water tap can be accessed. Put the jointer of the water
inlet hose on the tap. See to Figure 2. (If the tap diameter is too large and the jointer
can not be set on the water tap, please loosen the four screws and take out the
bushing in the jointer. See to the figure3.)
Water inlet pipe jointer
Slider
Locking lever
Water inlet pipe
Figure 1
Screwdriver
Figure 2
4.Fasten the four screws evenly. See to Figure 4.
5.Take off the nameplate. Twist the fastening nut as per the indication of the figure.
See to Figure 5.
Remarks: Before twisting the fastening nut, the thread is 4mm above the
upper surface of the nut. After twisting the fastening nut, the thread is 2mm
above the upper surface of the nut. See to Figure 6.
Nut
Figure 4
Figure 5
Screw
Mark label
About 4mm before twisting
About below 2mm after twisting
Figure 6
bushing
Figure 3
PROGRAM
STANDARD
HEAVY
SOFT
SAVE
SINGLE WASH
TUB CLEAN
INDICATION OF PROCESS
(NO CHOOSING)
SOAK
WASH
RINSE
SPIN
WATER
LEVEL
PROGRAM
RESERVE
START
PAU SE
POWER
ON/OFF
1 Press the "POWER ON/OFF" button to switch on
the power supply
POWER
ON/OFF
2 Press the button of" " to select
PROGRAM/RESERVE
a suitable full-automatic program
PROGRAM
RESERVE
After switching on, the "Standard" program will be the default. If other full-automatic program is
desired, you can press the button " " to get the corresponding
indicator on. Refer to the "Button of ' '"
paragraph on page 10.
Example: Use the "Save" program for slightly soiled articles.
When "standard" program is selected, the washing
machine will perform full-automatically controlled fuzzy
program to set water level, water flow and wash duration
according to the cloth nature and weight
PROGRAM/RESERVE
PROGRAM/RESERVE
Page 10
The appliance is to be connected to the water mains using new hose-set
and old hose-set should not be reused.
6
11
Page 8
Use the operation buttons
Description of the function of the buttons
a.
Indicator mode and meaning
Off:
Flashing: indicate the running program
On: indicate the program about to run,or
indicate the selected mode
PROGRAM
STANDARD
HEAVY
SOFT
SAVE
SINGLE WASH
TUB CLEAN
INDICATION OF PROCESS
(NO CHOOSING)
SOAK
WASH
RINSE
SPIN
WATER
LEVEL
" WATER LEVEL"button
The user selects a suitable water level
depending on the load.
Remarks: After pressing "POWER ON/OFF" to connect power supply, if the washing machine
lasts idle more than 5 min, it would automatically shut off the supply.
"POWER ON/OFF"button
Press "Power On/Off" button to connect
power supply.
After power is connected, pressing this
button will cut off the supply.
"START/PAUSE"button
After the power is switched on, press it to
start the machine
During working, push it to pause working.
During pause, push this button to restart
and continue operation.
START
PROGRAM
RESERVE
PAU SE
"PROGRAM/ " buttonRESERVE
Press
"PROGRAM/RESERVE " button
you can select one or several of
Standard ,Save,Single wash
and Tub clean
Press
over 2 seconds, the program
of peservtion.
reserved hours to the wash cycle end. The
indicator flashes to indicate in-reservation.
,Heavy,Soft
"PROGRAM/RESERVE " button
.
you can select
the N tube displays the
ixie
programs
POWER
ON/OFF
Connection between the water inlet hose and the
washing machine
1.Do not take off the water absorption
cushion. Please check if the cushion
is dropped or damaged before each
usage. If it happens please contact
our after-sale department immediately.
2.Put the nut of the water inlet hose on
the valve jointer.
3.Fasten the nut. Swaying it gently to
confirm if it's suitable.
Jointer of the water inlet valve
Nut of the water inlet hose
Water absorption cushion
Connection between the jointer of the water inlet
hose and the water inlet hose
1.Push down the slider. Insert the
water inlet hose into the jointer.
2.Hang the lock lever to the jointer.
Release the slider till a click
sound is heard.
Locking lever
Jointer of the water
inlet hose
Slider
Check the connection between the jointer of the
water inlet hose and the water tap
1.Swaying the hose gently to confirm if it is fastened
stable.
2.After installation, open the tap to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if
the connection between the jointer
of the water inlet hose and the water
tap, and the installation of the
water inlet hose are firm, so as to
prevent dropping from improper
Take down the water inlet hose
1.Close the water tap.
2.Press the locking lever. Push down the slider. Then
pull off the water inlet hose. If the machine is used
more than once every week, the jointer of the water
inlet hose can be kept on the tap to prevent
damaging the fixing screw.
Locking lever
Slider
10
7
Page 9
Preparation before washing
Put in the laundries
Preparation before washing
1.Connect the water inlet hose and open
the water tap .
2.Confirm that the washing machine is
earthed reliably . Then insert the power
plug into the receptacle. Do not connect
the earth terminal to the gas pipe and
tap water pipe.
3.Put down the drain hose.
Pay attention to followings before washing the laundries
Confirm if
there's special
requirment for
the laundries.
a.Please check if the laundries are applicable for washing.
b.Separate those not colorfast from other laundries.
c.For laundries not waterabsorbing,please put them into water with hands.
d.For laundries with much soil,please remove the soil first.You can add detergent on the
part with serious soil directly.It is much easier to remove the soil by that mean.
e.For laundries likely to get lint ball or with long fiber,please first turn the inside out before
putting them into the water.
f.Do not put the laundries polluted with chemicals directly into the washing machine.
g.For those small laundries ,laundries likely to be twisted or worn,and woolen laundries,
please put them into mesh bag before wasing.
Clear the pocket.
Take out the
coins , sand,
hairpins etc.
Fasten the
buttons and
zippers.
The quantity of
the laundries
shall not exceed
the rated value.
The big laundries
like the jeans
shall be put in
loosely.
When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion,please
put the laundries
with buttons into
other laundries.
The capacity of washing and spinning of the
machine refer to the largest weight of the standard
laundries under dry condition that can be washed
or spinned in one time. One time washing quantity
shall be lower than the standard capacity.
The thickness, size, type of the cloth will influence
the actual washing capacity. It is suitable for one
time washing to put in reasonable amount of
laundries and the laundries can be turned round in
washing.
Do not select "High" water level for laundries less
than 1.0kg, so as to avoid splashing of water.
To wash thin laundries like the stocking, silk etc.,
please first put them into washing mesh bag (which
can be purchased separately) before wash.
Usage of the detergent
How to use the washing
powder
Direct dissolved in the machine
1.Fill water to "Low" water level.
Inlet box of the detergent
How to use the whitener
Fill water to decided level. Dilute
the whitener with container. Pour
it slowly into the washing tub.
Avoid using whitener on
laundries with color or pattern as
they are prone to lose color.
The whitener shall not touch the
laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
For powder whitener, please
dissolve it before use.
2.Add the power. Run for 30 seconds
to dissolve it completely.
3.Put in the laundries. Select
suitable water level.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 and a
container.
2.Add the powder while stirring to
fully dissolve it.
Put in the prorer quantities detergent
according to the water level and the
laundries quantities .
It is suggested not to use high
sudsing detergent.
Washing powder with poor quality or
long time storage maybe caked.
Please pay attention to cleaning the
detergent box in time
8
9
Loading...