Haier HWM65-828 User Manual

Double Drive Fully Automatic Washing Machine
User's manual
This manual is for
HWM65-828
Please read this manual carefully before using. Retain it for future reference.
CONTENTS
Names of the parts 1
Safety precautions 2
Installation and adjustment 4
Preparation before washing 9
Put in the laundries 10
Usage of the detergent
Use the operation buttons 11
Close the top lid 14
Finish washing 14
Disposal after washing 15
Trouble-shooting answer to question 16
Packing list 17
Specifications 17
10
Packing list
°
User anual's m
Components of the water inlet hose
Bottom plate
Inner cover component
One
One
One
One
Inside the document bag
Inside the accessory bag
Between the upper cushion of the washing machine package and the upper seal of the package carton
Inside the accessory bag
Double Drive Full Automatic
washing machine
Specifications
Water level/Water
quantity (about)
Water injection pressure
Washing / Spinning capacity
One
0.03MPa 1.0MPa
~
6.5kg/6.5kg
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself..
Phenomena The reason How to settle
The digitron displays E0.
The drainage cannot work, or is too slow. The digitron displays E1.
It stops running in midway. The digitron displays E2.
The safety switch acts, and the spinning cannot work. The digitron displays E3.
The water filling does not work, the digital displays E4.
The digitron displays E6.
The machine does not act
Not wash
Not spin
There's abnormal sound
inside the machine
The water tap leaks
Common phenomena
Phenomena Explanation
The spinning is intermittent when it starts.
The wash procedure is paused.
Push the PROGRAM button to select SPIN,
but it doesn't work.
The pulsator pauses during water inlet in wash and rinse.
There may be some water flowing out of the drain hose in the first use of the machine.
The top lid is opened during reserve procedure.
Is the drain hose put down? Is the drain hose blocked?
The top lid is not closed.
Are the laundries put slantingly? Is the machine slanting?
Is the water tap opened, or is there water supply failure? Is the water inlet valve blocked? Is the water pressure too low?
The water level sensor is bad.
Is there power failure? Is the power plug inserted tightly? Is the water level reached preset position?
Is the power plug inserted tightly? Is the top lid closed reliably? Are the laundries set flat?
Is the machine slanting? Are the laundries put slantingly in spinning? Are there any foreign materials?
Is the screw of the jointer of water inlet hose loose or awry?
Balance the laundries to avoid slanting.
The cloth sensor is checking the cloth, it will add water after 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
It is to avoid splashing during water inlet.
It is the water remained in the factory inspection of performance.
Close the top lid.
Put down the drain hose. Open and close the top lid once. Clean the foreign material. Open and close The top Lid Once.
Close the top lid.
Reorder the laundries. Close the top lid. The machine will start running after 10 seconds of being placed horizontally.
Open the water tap.
top lid once.
Clean the water inlet valve.
the top lid once. Open and close the top lid once.
the water pressure is normal.
Please contact the after-sales service department.
Please use it when there's power supply. Insert the power plug tightly. Fill water to the preset position.
Insert the power plug tightly. Close the top lid. Set the laundries flat.
Adjust the machine to be even Reorder the laundries and close the top lid. Remove the foreign materials.
Fasten the screw of the jointer properly.
Open and close the
Open and close
Use until
Names of the parts
Top lid component
Inner cover
Detergent box
Control panel seat
Soften inlet
Balance ring
Filter cover
Lint filter
Attach block
Adjustable foot
Water absorption gasket
Outer tub cover
Inner tub
Water inlet valve
Drain protective lid
Cabinet
Adjustable foot label
Power cord
Hook
Pulsator
Back cover
Base frame
Meaning and description of the symbols
Warning sign
Forbidden sign
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.otherwise
it may cause damage of the machine or injure the personal
safety of the user.
Contents marked with that symbol are actions forbidden
to perform. Performing of those actions may result in damage of
the machine or influence the personal safety of the user..
Screw cover
Cabinet handle
Drain hose
Drain bushing
Fixed foot(3)
1
Loading...
+ 7 hidden pages