Haier HWM62-0566 User Manual
Fully automatic washing machine
This manual is for
HWM62-0566
User's manual
Please read this manual
carefully before using.
Retain it for future reference.
Contents
Names of the parts
Safety precautions
Installation and adjustment
Usage of the drain hose
Installation the water inlet hose
Preparation before washing
Put in the laundries
Usage of the detergent
Close the top lid
Use the operation buttons
Finish washing
Disposal after washing
Trouble shooting
Packing list Specification
Answer to question
*
*
Names of the parts
Top lid component
Control panel seat
Liquid whitener inlet
Filter cover
Liquid whitener inlet
Lint filter
Inner tub
Pulsator
Front control board
Cabinet
Base
Water inlet
valve
Inner cover component
Detergent box
Attachment block
Handle
Hang hole of
drain hose
Drain hose
Adjustable foot
seam
Adjustable leg
Water absorption
cushion
Power line
Back cover
Fixed leg
(3 pieces)
Notes: All illustrations in this Manual are given for reference only. Your products
and accessories may show differences from these illustrations due to our
continuous improvement.
Meaning and description of the symbols
Contents marked with that symbol are related
Warning sign
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Forbidding sign
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
1
Safety precautions
Please insert the power cord into
special receptacle with rated voltage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be inserted and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
In case the washing machine is installed on ground with carpet, do not
block the ventilation hole with carpet.
The ventilation holes
at the bottom
Do not use water hotter than 50 C .
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
2
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
The handicapped or children without
care shall not use the machine.
Do not decompose, repair or alter the
machine by yourself.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
l
r
e
Petro
inn
h
T
Keep the machine away from direct
sunlight and heat source like the heater.
Please keep the lint filter in good condition,
and install it to proper position during
washing. If the lint filter is lost or
damaged, please contact the customer
care agent of our company.
.
Install
Dismantle
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
To change the direction of drain pipe, please contact the customer care agent of our company.
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use
otherwise the washing effects may be lowered or the washer may be damaged.
3
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Install the inner cover component
Before using the washing machine firstly, please install the inner cover component.
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming the inner cover shaft to the installation
hole of the corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of the left side into the corresponding outer tub cover shaft groove(see
to the figure 1), then hold the middle position of the front of the outer tub cover with left hand forcibly ,
handhold the right and below position of the inner cover with right hand, push the inner cover to the
outer cover vertically, make the inner cover shaft into the corresponding outer tub cover shaft groove(see
to the figure 2). Please install to designated position to guarantee there are no dropping or abnormal
sound in opening and closing of the inner cover, and the operation shall be smooth. Do not dismount the
inner cover component after washing.
Outer tub cover
Outer tub cover shaft groove
Figure 1
Inner cover shaft
Inner cover component
Left hand
After opening the package, please lean the washing machine gently down on
soft items (like towel cloth,blanket, etc.). Install the bottom plate to the bottom
of the machine with one screw by a cross screwdriver, then lift the machine up
gently. See to the figure:
I enlarge
I
Front
Right hand
Figure 2
Carpet
Back
The two claws of bottom plate should
insert the two strip holes ,and insure
Adjust the Installation position
The washing machine away from wall should be overrun 20mm. The largest allowable slope of the shank
base of the machine is 2 .The slanting or rough ground will result in unstable running or stoppage of the
machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is horizontal.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the side of the
leg slightly, loosen the adjustable nut, and twist the leg.
2 . After adjustment, fasten the nut.
Loosen
High
Fasten
Low
the adjustable nut
the adjustable feet
4
Loading...