Haier HWM60-78 User Manual

User's manual
Specification
Model XQS60-78
Rated voltage frequency 220V ~ 50Hz
Rated washing / spinning capacity 6.0kg (weight of standard dry cloth)
Water level/Water quantity (about)
Max water consumption
Rated washing power 380W
Rated spinning power 260W
Weight About 32.5kg
Dimension L 560 mm W 630mm H 890 mm
1/12L 2/16L 3/20L 4/25L 5/29L 6/33L 7/38L 8/42L 9/47L 10/50L
About 75L(High water level; Normal program)
XQS60-78
Computerized Automatic Washing Machine
Please read this manual carefully before using. Retain it for future reference. Please check if the power receptacle has good earthing condition before using to guarantee your safety. The manufacturer will not take responsibility for those risks occurred from not obeying this manual.
CONTENTS
Before using
Names of the parts.............the 2nd cover
Safety precautions .............................................1
Installation and adjustment .........................3
Install the water inlet hose............5
Using process
Preparation before washing........................7
Put in the laundries ...........................................8
Usage of the detergent .....................................9
Use the operation buttons ...................10
Close the top lid .................................14
Finish washing ...................................14
Disposal after washing .........................15
Trouble shooting Answer to question..............................16
Packing list.....................................17
Specification................the back cover
Special number:0030804888
Names of the parts
Before Using
Before Using
Packing list
Adjustable leg film
Accessories
Top lid handle
Round cover Attachment block
Pulsator
Water inlet valve
Water absorption cushion
Cabinet handle
Power cord Drain hose
Back cover
Inner cover component (1 piece)
Bottom plate (1 piece)
Fastening screws
(8 pieces)
Top lid component
Inner cover component
Detergent box
Liquid whitener inlet
Control panel
Outer tub cover
Balance ring
Lint filter
Inner tub
Front control board
Cabinet Cabinet base
Adjustable leg
Fixed leg (3 pieces)
The end connecting to the washing machine
Jointer connecting the water inlet hose and the water faucet
The end connecting to the water
inlet hose jointer
Water inlet hose (1 piece)
Water inlet hose joint (1 piece)
Name
User's manual
Warranty manual
Components of the water inlet hose
Bottom plate
Tapping screws
Inner cover component
Computerized automatic washing machine
Quantity
One
One
One
One
Eight
One
One
Storage position
Inside the document bag
Inside the document bag
Inside the accessory bag
Between the upper cushion of the washing machine package and the upper seal of the package carton
Inside the accessory bag
Inside the accessory bag
Meaning and description of the symbols
Contents marked with that symbol are related to the safety of the product and the personal
safety of the users. Please operate in strict conformity to the contents.
Contents marked with that symbol are actions forbidden to perform. Performing of those
action may result in damage of the machine or influence the personal safety of the users.
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomenan The reason How to settle
The digitron displays E0.
The drainage cannot work, or is too slow. The digitron displays E1.
It stops running in midway. The digitron displays E2.
The safety switch acts, and the spinning cannot work. The digitron displays E3.
The water filling does not work, or is slow. After about 40 minutes later, the digital displays E4.
The digitron displays E6.
The digitron displays E8.
The digitron displays E9.
Not wash
The machine does not act
Not spin
There's abnormal sound inside the machine
The water tap leaks
The top lid is opened during reserve
procedure.
Is the drain hose put down? Is the drain hose blocked?
The top lid is not closed.
Are the laundries put slantingly? Is the machine slanting?
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked? Is the water pressure too low?
The water level sensor is bad.
The power voltage is too low.
The power voltage is too high.
Is there power failure? Is the power plug inserted tightly? Is the water level reached preset position?
Is the power plug inserted tightly? Is the top lid closed reliably? Are the laundries set flat?
Is the machine slanting? Are the laundries put slantingly in spinning? Are there any foreign materials?
Is the screw of the jointer of water
inlet hose loose or awry?
Close the top lid.
Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
Close the top lid.
Reorder the laundries. Close the top lid. The machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.
Please contact the after-sales
service department.
Pull off the power plug. Wait for the
voltage resuming normal before usage.
Please use it when there's power supply. Insert the power plug tightly. Fill water to the preset position.
Insert the power plug tightly. Close the top lid. Set the laundries flat.
Adjust the machine to be even Reorder the laundries and close the top lid. Remove the foreign materials.
Fasten the screw of the jointer properly.
Safety precautions
Please plug the plug on special 220V AC receptacle. Be sure to use single-phase three pins receptacle.Ensure the earthing prong of the power receptacle is earth­ed reliably.Use leakage protector if possible.
Earth
Do not bend, stretch, twist, bind the power cord by force, or reformit. Do not press or clamp it with heavy items. If the power cord and power plug are bad, or the receptacle is loose, be sure to have it replaced by the technicians of our special shop or our agent,or the after-sales service department to avoid any risk.Keep the prong of the power plug clean.If dust is found on the power plug, please wipe it off with dry cloth.
In case the washing machine is installed on ground with carpet, be careful not to block the ventilation hole with carpet.
The ventilation holes at the bottom
Soft items
Do not put the machine at damp place like the bathroom. Never wash it with water. Do not put wet laundries on the control panel coating
In normal usage of the washing machine, the power plug shall be ready to be pulled or plugged with hand. Be sure to pull the plug off and close the water faucet when occurring power failure,delivering the maching, setting the machine idle or cleaning the machine,Do not plug or pull the power plug with wet hand.
Do not use water with temperature higher than 50
Do not wash water-proof laundry like the raincoat, bikecovers, down textiles etc. To avoid abnormal vibrations in spinning and damages to the laundries.
.
Before Using
Before Using
Common phenomena
Phenomena
The spinning is intermittent when it starts. The wash procedure pauses.
Select SPIN program, but it does not work.
The pulsator pauses during washing,rinsing or
adding water. There may be some water flowing out of the drain hose in the first use of the machine.
When the power plug is inserted,the computer board indicator is switched on,and the machine starts working
Explanation
Balance the laundries to avoid slanting.
The cloth sensor is detecting , it will add water after about 48 senconds The program is setting the drain time , A certain period is needed before it starts spinning. It is to avoid splashing during water filling.
It is the water remained performance inspection by the factory.
It is the special power resum efunction.In the cass of power failure or the power
plug is loose during washin,the machine can save the running program,and
resume the program after the power supply is recovered.You do not need to set
the program again.
Do not let the machine share one receptacle with other electric appliances. If the power plug is damaged, or the plugging into the receptacle is loose, do not use the plug any more.
Loading...
+ 7 hidden pages