Haier HWM60-112P User Manual
User's manual
HWM60-112P
Twin-tub Washing Machine with Pump
Please read this manual carefully before using.
Retain it for future reference
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
The manufacturer will not bear the responsibility for
those risks occurred from not obeying this manual.
Contents
Before using
Names of the parts.............the 2nd cover
Safety precautions ...............................1
Installation and adjustment ..................3
Introduction of the major functions .......5
Using process
Preparation before washing ................6
The musts in washing .........................7
Usage of the detergent .......................8
Washing sequence ..............................9
Disposal after washing .......................13
Trouble-shooting*
Answers to question.....................15
Packing list ......................................17
Specification..............the back cover
Names of the parts
Buzzer
Water-filling entrance
Water inlet selector handle
Wash selector
Wash timer
Control panel
Overflow filter
Quick water-filling entrance
Drain hose hook
Water level adjusting lever
Lint filter(installed by user)
Pulsator
Wash tub
Drain hose
Wash tub cover
Base frame
Before Using
Before Using
Outer cover of the spin tub
Inner cover of the spin tub
Spin timer
Spin tub frame
Spin tub
Cabinet
Power cord
Accessories
Water-filling jointer
(one piece)
Water inlet hose
(one piece)
Lint filter
(one piece)
Gland
(one piece)
Meaning and description of the symbols
Contents marked with that symbol
Warning sign
Forbidding sign
are related to the safety of the
product and the personal safety
of the users. Please operate in
strict conformity to the contents,
otherwise it may cause damage
of the machine or injure the
personal safety of the user.
Contents marked with that symbol
are actions forbidden to perform.
Performing of those actions may
result in damage of the machine
or injure the personal safety of
the user.
Safety precautions
Before Using
Before Using
Please insert the power cord into special
receptacle with rated voltage.Be sure to
use single-phase three pins receptacle.
The earthing terminal of the receptacle
must be earthed reliably.If possible,please
adopt electric leakage protector.
Earth
If the supply cord is damaged, it must be replaced by the manufacturer,it s service
agent or similarly qualified persons in order to avoid a hazard.
Power
The carpet must not obstruct the ven
tilation openings in the base of the wa
shing machine
plug clean.
.
The washing machine should be position
ed so that the plug is accessible
to pull the plug off when there'spower failure, or the machine is being moved, cleaned or when it is idle.
Keep the pin of the
-
Do not use water hotter than 50 C .
-
. Be sure
'
-
Ventilation hole at
the bottom of the
washing machine
Do not put the machine at damp place
like the bathroom . Never wash it with
water. Do not place wet laundries on the
control panel.
Do not share one receptacle with other
electric appliances. Do not use it in
case that the power plug is damaged
or the inserting into the receptacle is
loose.
Do not wash water-proof laundries such
as the raincoat, bicycle shelter etc. To
avoid abnormal vibration during spinning.
Safety precautions
Before Using
Before Using
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not decompose, repair or alter the
machine by yourself.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
Petrol
Thinner
Handicapped or children without care
shall not use the machine.
To protect your laundries and washing
machine, please take out all of the coins,
buttons, sand, hairpin and other foreign
materials before washing.
Keep the machine away from direct
sunlight and heat source like the
heater.
Please check if the water faucet is open, and if
the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
Installation and adjustment
Before Using
Before Using
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than 1.2m , or the drainage will
not be smooth enough and cause incomplete drainage.
<1.2m
2.Do not step on or press the drain hose.
Install the lint filter
After opening the package,please take out the
lint filter from the document bag,install it
to the overflow filter of the cabinet.
See to the figure
Overflow filter
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling
entrance on the control panel, then push the
water-filling jointer into the entrance on the
control panel. (To dismantle the water inlet pipe,
just push the control handle as indicated in the
figure and pull it out)
Select water level according to the
quantity of the laundries.
Set the water level adjusting lever
to needed line.
Page8
High
about 55L
Medium
about 46L
Low
about 36L
Water inlet hose
Push
Control handle
Water level
indicator
High
Medium
Low
Lint filter
Water inlet jointer
Water inlet
Before Using
Before Using
How to change the direction of the drain hoses
Figure 1 indicates the ex factory
installation position of the drain
hose.
Figure 1
Extend the drain hose from the side of spin tub.
Take off the drain hose from the hanging
hole of the cabinet. Pull the drain hose
fixing hook outwards gently to take out
the drain hose from the two fixing hooks.
(As per Figure 2)
Rotate the drain hose fixing hook for 90
to take it out from the installation hole
(As per Figure 3).
Install the two drain hose
fixing hooks taken out into
the installation hole at the
other side of the base frame
(to aim at the installation
hole accurately you can
lean the washing machine
forward slightly).Then rotate
for 90 (As per Figure 4).
Drain hose
fixing hook
Rotate the fixing
hook for 90
Take off the fixing
hook downwards
Figure 3
Side sectional view
Drain hose
fixing hook
Pull outwards
slightly
Take off
the drain hose
Figure 2
Rotate the fixing
hook for 90
to fix it
Insert the fixing hook into the
installation hole upwards
Figure 4
Fixing hook
installation hole
Drain hose
Pull the fixing hook outwards slightly.
Inlay the drain hose into the fixing hooks
reliably along the groove at spin tub side,
and make it extend towards spin tub side.
Then hang the drain hose into the hanging hole at the spin tub side. (As per Figure
Figure 5
Figure 6
Extend the drain hose from the rear side
Take out the drain hose from the fixing hook. Extend it from the rear side (When
the drain hose is extended from the rear side, it can be hung on the point for drain
hose at the two sides of the cabinet.) (See to Figure 6).
Loading...