Haier HWM60-10A User Manual

Multiple program for washing

Weeny adjustment of time and degree

HWM70-10A

Please read this manual carefully before using.
Retain it for future reference

Please check if the power receptacle has good earthing
condition before using to guarantee your safety.

The manufacturer will not bear the responsibility for
those risks occurred from not obeying this manual.

Specifications the back cover

Contents

Before using

Using process

Trouble shooting *
Answers to questions 18

7
8

Put in 9

10
17
17

Preparation before washing
Put in the laundries

detergent and softener
Use the operation buttons
Close the top lid
Finish washing
Disposal after washing 17

Names of the parts The 2nd cover
Safety precautions
Installation and adjustment
Install the water inlet hose 5

1
3

19

User's Manual

Computerized Full-auto
Washing Machine

Honourable users:

Thank you for choosing our products.
Our products intergrade high-tech,precision,frontier science.
To facilitate using it,please read this manual carefully and operate this machine according to it.

Adjustable foot

Adjustable foot film

Fixing foot(three)

Drain hose hanging hole

Rear cover

Power cord

Drain hose

Handle

Cabinet

Control panel

Control panel film

Pulsator

Inner tub

Scour container

Top lid

Before Using

Names of the parts

Water absorption cushion

Contents marked with that symbol are related to the safety of the product and the personal
safety of the users. Please operate in strict conformity to the contents, otherwise it may
result in damage of the machine or influence the personal safety of the users.

Contents marked with that symbol are actions forbidden to perform. Performing of those

actions may result in damage of the machine or influence the personal safety of the users.

Accessories

Meaning and description of the symbols

Water inlet hose

Water inlet hose joint

Tapping screws

ST4X16
(eight pieces)

the end connecting to the washing machine

jointer connecting the water
inlet hose and the water faucet

the end connecting to the water inlet hose jointer

Bottom plate
(one piece)

Decorative faceplate

(one piece)

(one piece)

The ventilation
holes at the bottom

Soft object

Before Using

Before Using

Safety precautions

Do not put the machine at damp place like
the bathroom. Never wash it with water.

In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.

Do not let the machine share one receptacle with other electric
appliances. If the power plug plugging into the receptacle is
loose, do not use the plug any more.

Do not wash water-proof laundries like the raincoat,
bike covers etc. to avoid abnormal vibrations in spinning.

Do not use water hotter than 50 C .

Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.

In normal usage of the washing machine,
the power plug shall be ready to be pulled
or plugged with hand. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
cleaning the machine. Do not plug
or pull the power plug with wet hand.

Do not bend, stretch, twist, bind the power cord by force,
or reform it. Do not press or clamp it with heavy items. If the
power cord and power plug are bad, or the receptacle is loose,
be sure to have it replaced by the technicians of our special shop
or our agent, or the after-sales service department for the sake
of avoiding any risk. Keep the prong of the power plug clean.
If dust is found on the power plug, please wipe it off with dry cloth.

Earth

To protect your laundries and machine, please
clear the pocket, take out the coins, sand,
hairpins etc before washing.

Please set down the drain hose, connect the
water inlet pipe and unbolt the water faucet.
Advice to use lower foamy powder.

Do not stretch hands into the working machine.
It is dangerous even if the rotation is slow.
Take special care of the children.

Do not decompose, repair or alter the machine
by yourself.

Do not put any hot or heavy items (such as the kettle
with hot water) on the washing machine

Do not wash laundries with volatile materials
(such as thinner, petrol etc.).

Keep the machine away from direct sunlight and
heat source like the heater.

The handicapped or children without care shall not
use the machine.

Benzene

Before Using

Safety precautions

The lint filter shall be kept in good condition, and
installed to proper position. If the lint filter is lost
or damaged, please contact the local after-sales
service department of our company.

Dismantle

Install

The largest allowed slope of the shank base of the machine is 2 . The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal

Adjust the adjustable foot

Hang the plumb to confirm it's horizontal

Install the bottom plate

Adjust the Installation position

Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.

Before Using

Before Using

Installation and adjustment

After you open the package, please lean the washing
machine gently down on soft items (like the towel cloth,
blanket, etc.).
Install the bottom plate to the bottom of the machine
with the eight screws by a cross screwdriver, then
lift the machine up gently. See to the right Figure:

(1) To twist the adjustable foot at the right front of
the cabinet (front the sight of front), please first
lift up the side of the foot slightly, loosen the
adjustable nut, and twist the foot.

(2) Fasten the nut after adjustment.

Loosen

Fasten

High

Low

adjustable nut

adjustable foot

Before Using

Before Using

1.The height of the drain hose shall be

less than 10cm, or the drainage will not
be smooth, and cost such long time that
the machine may stop at mid way.

2.Do not ramp or press the drain hose.

3.If the drain hose is too long, cut it at mid

point. To make smooth drainage, cut the
front end of the hose slantingly.

4.If extra drain hose is needed, please

make separate purchase. The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.

How to change the direction of the drain hose

Usage of the drain hose

The drain hose shall drain smoothly

If the extra hose is too long, cut it
either at A or at B point.

1.Dismantle the rear cover of the washing machine.

2.Lean the machine down gently with the front
surface facing the ground. Loosen the eight
screws by a cross screwdriver.

4.Dismantle the drain outlet protecting cover at the
other side, and replace it with drain hose nut as
indicated in Figure 2.

5.Extend the drain hose from the other side. Fix the
drain hose with drain hose frame onto the cabinet
as indicated in Figure 3.

6.Install the drain outlet protecting cover to the other
side as indicated in Figure 4.

Install the bottom plate(method as described in page 3).
Lift up the machine gently. Then install the rear cover
of the machine.

3.Put down the drain hose. Take off the drain
hose nut and the drain hose frame as indicated
in Figure 1.Take the drain hose into the cabinet
as indicated in Figure 2.

Back

Front

Bottom

Drain hose nut

Drain hose frame

Drain hose

Soft item

Figure 1 Figure 2

Figure 3

Figure 4

Page 3

Drain outlet protecting cover

The exit end face of the faucet

Confirm the water faucet

water faucet, suitable water faucet, not suitable

It is required that the front end shall be longer than 10cm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.

2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise
it may leak water. See to Figure 3.)

1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the

water inlet hose component. See to Figure 1.

3.Fasten the four screws evenly. See to Figure 4.

about 4mm after twisting

Remark: .Before twisting the fastening nut, the threading is 4mm above the upper
surface of the nut. After twisting, the threading is less than 2mm above the upper
surface of the nut. See to Figure 6

About above 2mm after twisting

water inlet hose jointerwater inlet hose jointer

Screw knife

Screw

Bushing

Nameplate

Screw nut

water inlet hose

Figure 1

Figure 4

Figure 2

Figure 5

Figure 3

Figure 6

Slider

Lock level

Before Using

Before Using

Install the water inlet hose

4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.

The exit end face of the faucet

Connection between the water inlet hose jointer and the water faucet

water faucet, suitable water faucet, not suitable

It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.

2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)

1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the

water inlet hose component. See to Figure 1.

3.Fasten the four screws evenly. See to Figure 4.

about 4mm after twisting

Remark: .Before twisting the fastening nut, the threading is 4mm above the upper
surface of the nut. After twisting, the threading is less than 2mm above the upper
surface of the nut. See to Figure 6

About above 2mm after twisting

water inlet hose jointerwater inlet hose jointer

Screw knife

Screw

Bushing

Nameplate

Screw nut

water inlet hose

Figure 1

Figure 4

Figure 2

Figure 5

Figure 3

Figure 6

Slider

Lock level

Before Using

Before Using

Install the water inlet hose

4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.