Haier HW-18CVA03 User Manual

ROOM AIR CONDITIONER

OPERATION MANUAL

HW-09CV03 HW-09CVA03 HW-12CV03 HW-12CVA03 HW-18CV03 HW-18CVA03

Please read this operation manual before using the air conditioner

Please keep it attentively

0010556533

CONTENTS

Safety precautions...................1

Air conditioner operation..........2

Care and Maintenance ............4

Air conditioner installation........5

Troubleshooting.......................7

SAFETY PRECAUTION

CAUTION

1.Do not install, remove and reinstall the unit yourself. Improper installation may cause leakage, electric shock or fire. Please engage an authorized dealer or specialist for the installation work.

2.The room air conditioner must be earthed.

3.Do not touch or operate with wet hands.

4.Do not turn on the unit by inserting the power plug. Do not switch off the unit by pulling out the power plug.

5.Do not insert sticks, fingers or other objects into the unit.

6.If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.

7.After installation, the power plug should be easily reached.

8.The wiring method should be in line with the local wiring standard.

OPERATION CONDITIONS

Applicable ambient temperature range:

Operation Guide

Auto swing switch

When the swith is set to “ON”, vertical louver will swing from side to side, delivering gentle air thus making you feel very comfortable.

When it is set to “OFF”, vertical louver will stop at position.

Test

Mode selection

run

OFF

cool

fan

LO fan

cool

HINTS

Auto swing

OFF ON

HW-09CV03 HW-09CVA03 HW-12CV03 HW-12CVA03

Thermostat switch

Temp. setting

COOL

Wait 3 minutes before restarting.

This switch controls the preset indoor temperature to make the air conditioner start or stop automatically, so as to reduce power consumption and operate the system both comfortably and economically. Operate the switch as follows: Temp. decreases as the switch is turned form “1” to “9”. Temp. increases as the switch is turned from “9” to “1”.

“Test run” mode. (For model HW-09CV03, HW-12CV03, HW-09CVA03, HW-12CVA03 only) When switch set to this position, air-con will run continuously regardless of temp. setting. Don’t use test run for normal operation.

The compressor stops running when the set temperature is reached but the fan continues to operate to keep an even indoor temperature.

CAUTION

In cooling mode, after you turn thermostat switch counter-clockwise,do not turn it back until at least 3 minutes have elapsed.Otherwise, the fuse may blow due to overload. Do not exceed the selection range.

Mode selection

OFF

LOW FAN

MAX

LOW

COOL

HIGH COOL

HIGH

FAN

COOL

MIN

Temp. setting

Auto swing

OFF ON

WAIT THREE MINUTES BEFORE RESTARTING

HW-18CV03 HW-18CVA03

Mode selection switch

Mode switch controls the fan motor speed. Cooling speed or fan speed.

When set to “HI fan”, fan motor runs at high speed to blow out strong air. When set to “LO fan”, fan motor runs at low speed to blow out gentle air. When set to “HI cool”, air-con will start cooling at high speed, blowing out strong air. When set to “LO cool”, air-con will start cooling at low speed, blowing out gentle air. When set to “OFF”, air conditioner stops running.

HINTS

When mode selection switch is shifted to “HI fan” or “LO fan”, air-con will only blow out air without cooling.While the air conditioner running, its mode selection shouldn’t be shifted frequently between “HI fan” and “HI cool”, “LO fan” and “LO cool”.

Cooling

Max.Temperture:

Min.Temperture:

AIR CONDITIONER OPERATION

Indoor

D.B D.B

32 C

18 Co14 C

W.B

23 C

43 C

18 C

Outdoor

W.B

26 C

PART INDENTIFICATION

Machine body

Front panel

Machine body

Air inlet

(outdoor side)

Air filter (inside)

Air inlet (indoor side)

Operation panel

Air outlet (indoor side)

Mode selection

Temp. setting

Auto swing

OFF

COOL

OFF ON

fan

Test

cool

run

Wait 3 minutes before restarting.

D.B :Dry Bulb Temperature

W.B :Wet Bulb Temperature

Ventilation

(For model HW-18CV03

HW-18CVA03 only)

The ventilation lever must be CLOSE position in order to maintain the best cooling conditions. When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is exhausted.

Note:

It is advisable not to keep horizontal flap at downward position for a long time in COOLor FAN mode,otherwise , condensate water might occur.

Don't move the vertical flap with hand in order to avoid the vertical flap abnormal, using the

AUTO SWING switch to adjust the move of vertical flap.

CARE AND MAINTENANCE

Always turn off the air conditioner and the main power supply before clean the unit. Switch off the power supply if the unit is not going to be used for a long period of time.

Air filter cleaning

It is advisable to clean air filter every two weeks for longer operation.

Cleaning of the

air filter

(You will find how to clean the filter on page 2 .)

OPENCLOSE

Notes

Avoid opening doors and windows unless necessary.

Don't be exposed to cold air for a long time.

Set temp . a little bit higher before going to bed.

Proper temperature

Air filter cleaning

Before cleaning, turn off the power.

Do not circumgyrate the

When dirt accumulates on air filter, air circulation will be blocked, which causes poor cooling. It is advisable to clean air filter every two weeks for longer operation.

Take out the air filter

front panel any more than

° to the unit or damage

to the tabs may occur.

Air filter(inside)

1.Loose the air inlet by pushing “PUSH” at both edges as shown.

2.Open the air inlet.

3.Remove the air filter.

Clean the filter

1.Gently flap the dirt off the air filter.

2.Carefully wash air filter in warm water(below 40°C).To obtain better cleaning effect,soap water or neutral detergent may be used.

3.Flush air filter carefully with clean water after removing dirt.Let it dry completely.

Installation of filter

1.Replacing the air filter.

2.Push the air inlet marked with “PUSH” until you hear a click.

CAUTION

PUSH

Airflow Direction

Airflow Direction Vane

The Vertical Airflow Direction Vane is manually controlled by positioning the vane to discharge the air upward, downward or straight out.

The horizontal air direction is adjusted by setting the AUTO SWING switch to the ON position.

Use curtain or blind Direct sunlight may reduce cooling effect, always use window curtain.

Don't hang clothes in the vicinity of air inlet. This will decrease cooling effect and cause abnormal operation.

Keep heat source away from air conditioner.

Temperature should be set properly when there are infant,child, the aged or disabled in the room.

Baby has gone sleep, better to adjust suitable temp.

After unit stops, don't restart it until 3 min. have elapsed.

OK! Enjoy a 3-min nap

Before operating mode selection switch, check that if the air inlet or outlet have been blocked.

AIR CONDITIONER INSTALLATION

(ONLY FOR REFERANCE)

INSTALLATION PROCEDURES

SELECTION OF THE INSTALLATION POSITION

1,The air-conditioner is better installed in shadow or in a place with short period of sunshine. In case the air-conditioner is installed at the point exposed directly to the sunshine, it should be protected from the direct sunlight as possible in order to avoid the long time of direct sunlight otherwise its performance will be lowered. (As illustrated in Fig. 1).

2. For the convenience of operation, it is recommended that air-conditioner be installed at least at the height of 760-1300 mm above the floor and no obstacles before it for a free airflow.

3.The shutters at both sides and the top of air-conditioner should be protruded outdoors free from being blocked by wall, window,ect.

4.The back of air-conditioner should be kept over 500mm from the obstacles (for example, wall, etc.) (As illustrated in Fig. 2).

5.To have an efficient drainage, the back part of the air-conditioner should be inclined downward by 5-10mm (As illustrated in Fig. 3).

>500mm

fig.2

NOTES:

For longer and trouble-free operation of the unit, pay special attention to the following:

Install air-con at a place strong enough to support the unit. Leave enough space around air inlet and outlet for better circulation. Avoid places where flammable gas leaks. Problems may occur if unit is installed in the following places: Place where oil exists in the air including engine oil or seaside with salt breeze blows and hot spring area with sulphurous gas in the air.

cover

support

5-10mm

fig.1

fig.3

1. Fix the prefabricated iron frame to stable position by expansible screws.

2. Put the whole machine with all the accessories installed, on

the iron frame. If there's water outlet flexible pipe, lead it to needed position(see Fig.1).

Fig.1

3. Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to prevent the entering of outer noise and the leaking of the coolness.

4. Open the Air inlet geille ,fix the front panel to the chassis firmly with the accessorial screw.(see

Fig.2 or Fig.3)

(NOTE:Your model will be the same as one of the right two illustrations,not both.)

Wall

Water outlet flexible pipe(provide by user)

Fig.3Fig.2

5. After installation of the conditioner, insert the power plug into the outlet and perform test-run.

THE ENCLOSED ACCESSORIES OF THE CONDITIONER

Name

Figure

Quantity

Manual

1 1 1 1

NOTE:Your model will have one Drain elbow of the above two, not both.

Drain elbow

(with seal ring)

Rubber lid Screw

PREPARATIONS BEFORE INSTALLATION

Make the wall hole or window hole (see Fig.1)

Iron frame

MODEL A B

HW-09CV03 HW-12CV03 HW-09CVA03

HW-12CVA03

HW-18CV03 HW-18CVA03

355mm 535mm

420mm 580mm

Width of the wall

Fig. 1

Cautions

Power cord: Be sure to use the exclusive power cord. Change installation place: If air-con need to be changed to another place please contact the dealer, who sold you the unit.

Always use at the rated voltage and with specfic air conditioning circuit

TROUBLESHOOTING

Before calling for service.

Check the following points before calling for repairs or service.

Phenomenon SolutionCause or check points

Switch on the machine but it does not work immediately.

If the machine is started after stop,it will need about 3 minutes to re-start so as to prevent the fuse from break.

Prepare unit for installation:

1.Take out the conditioner and accessories from the package .

2.Disposal of the condensed water.

Block the bottom plate hole of the conditioner with rubber lid, install drain elbow on the back hole and let the condensing water flow from the back hole of the conditioner. (See Fig.1 ) In this method, the accumulated condensed water in the bottom plate is hit by the fan onto the heat exchanger, and evaporated and blown out from the machin e. It can cool the heat exchanger adiator more quickly, and improve the energy efficiency of the conditioner. But the hitting noise by the fan at the outdoor side is relatively large.

NOTE: For some models your Drain elbow may be the same as Fig.2.

Fig.1

Rubber lid

Drain elbow

Switch on the machine but it does not work.

The cooling effect is not good.

Is plug firmly inserted? Is there power failure?

Does fuse get burned?

Is thermostat switch wrongly adjusted?

Is there any direct sunlight in the room?

Are doors or windows left open?

Are there any obstacles blocking air inlet and outlet?

Is air filter clogged?

Readjust power supply

Replace fuse.

Readjust the thermostat.

Use curtain or blind.

Shut doors and windows.

Remove the obstacles.

Clean it.

NOTE: When install drain elbow, adjust the direction of the drain elbow to make it be in line with the hole in the rear of unit; Insert the drain elbow into hole and twist 90°.

Fig.2

Drain elbow

Is there too much heat source in the room?

Remove the heat source

If problems can not be solved please pull out power plug and contact your dealer.