Haier HSU-30HEA03/R2(DB) Operation Manual
Please read this operation manual before using the air conditioner.
0010521199
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
Keep this operation manual for future reference.
Contents
2
3
6
7
1
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
TROUBLE SHOOTING
HSU-30HEA03/R2(DB)
Outdoor
Unit
Loading of the battery
Parts and Functions
Indoor Unit
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
Remote controller
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with th
e" + "/"-";
Load the battery,then put on the cover again.
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
change quickly.
After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
or decrease 1min. If the
button is kept pressed,time will
Inlet grille
Inlet
Air Purifying Filter
Outlet
Horizontal flap
Display board
(adjust up and do wn air flow
Don't adjust it manually)
(adjust left and right air flow)
Vertical blade
Emergency
Switch
Anion generator
(inside)
will increase
The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the
ver is apt to be disturbed in receiving
the signals,
so the distance to the indoor unit should be shorter.
type fluorescent lamp or
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up.
Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
Remove the batteries in case unit won't be in usage for a long period.
If there are any display
after taking-out, just need to press reset key.
Hint:
POWER/SOFT
The following functions and related displays are not
20
avai
lable:
Operation mode
AUTO
FAN
COOL DRY
Remote controller
HEAT
LOW HI
MED AUTO
If pressed, the other buttons
will be disabled. Press it once
again,lock will be cancelled.
30
.
LOCK
button
19
28
30
1.CODE
Used to select CODE A or
B with a press, A or B will
be displayed on LCD.
Please select A without
special explanation.
POWER/SOFT
When the remote
RESET
button
controller appears
abnormal, use a sharp
pointed article to press
this button to reset the
2
.
Control the lightening and
the indoor
extinguishing of
LED display board.
remote controller normal.
3.LIGHT button
26
4. TIMER button
5. CLOCK button
6. HEALTH button
7. MODE button
8. HOUR button
9. SWING button
10. ON/OFF button
11. TIMER ON display
12. FAN SPEED display
13. LOCK display
14. SWING UP/DOWN display
15. SLEEP display
16. HEALTH display
17. Operation mode display
18
.Singal sending display
19. POWER/SOFT display
20. Left/right air flow display
21. TEMP display
22. TIMER OFF display
23. CLOCK display
24. TEMP button
25. FAN button
26. HEALTH AIRFLOW button
27. SLEEP button
28. SET button
29. POWER/SOFT button
TEMP display
COOL display
HEAT display
HE
ALTH display
Dry display
TIMER OFF display
TIMER ON display
SLEEP display
AUTO display
Remote signal receiver
Display board
2
3
Operation
Air Flow Direction Adjustm
AUTO COOL DRY FAN HEAT
2.Select operation mode
Press FAN button. For each press, fan speed changes as
follows:
Press MODE button. For each press, operation mode
changes as follows:
Remote controller:
Remote controller:
Select a desired temperature.
4.Fan speed selection
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
LOW
MED
HI
AUTO
1. Unit start
Press ON/OFF on the remote controller, unit starts.
Base Operation
Remote controller
Operation
Mode
AUTO
Display Board
Remote
Controller
Note
COOL
DRY
HEAT
FAN
nothing
In DRY mode, when room temperature becomes
lower than temp.setting+2
o
C,unit will run intermittently
at LOW speed regardless of FAN setting.
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner
automatically adjusts the fan speed
temperature.
When FAN is set to AUTO, the
according to room
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.
Vertical flap
Pos.1
Pos.2
Pos.3
Pos.4
Pos.5
Pos.6
(Auto swing)
1.Status display of air sending
When restart after remote turning off, the remote
memorize the previous
Move the vertical blade by a knob on air
to adjust left and right direction referring to Fig.
2.Left and right air flow adjustment
(manual)
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
adjusted to left or
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.
conditioner
temperature is below 16
o
C, do not use it in the
Test operation:
Use this switch in the test operation when the room
normal operation.
your finger from the switch: the cooling
Continue to press the test operation
switch for more than 5 seconds. After
you hear the "Pi" sound twice,
release
Test operation switch is the same as emergency switch.
operation starts with the air flow speed "Hi".
Pi Pi
at air outlet if all vertical louvers are
right.
mode ,
controller will automatically
Note:
set swing position.
POWER/SOFT
Emergency Operation:
Emergency operation and test operation
Pi
Use this operation only when the
remote controller is defective or lost.
When the emergency operation
switch is pressed, the" Pi "sound is
heard once, which means the start
of this operation.
In this operation, the system
automatically selects the operation modes, cooling or
fan or heat, according to the room temperature.
When machine is running in emergency, the set value
of temperature and wind speed couldn't be altered;
meanwhile, it can't operate for dehumidifying or under
timing mode.
Press
button
Every time the button is pressed, temp.setting
increase 1
o
C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1
o
C,if kept depressed, it will decrease
rapidly
3.Select temp.setting
Loading...