Haier HSU-30HEA03-R2 User Manual
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-30HEA03/R2(DB)
Contents
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
TROUBLE SHOOTING
1
2
3
6
7
Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
0010521199
Parts and Functions
Indoor Unit
Inlet grille
Inlet
Outlet
Anion generator
(inside)
Horizontal flap
(adjust up and do wn air flow
Don't adjust it manually)
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
Display board
Remote signal receiver
ALTH display
HE
TIMER OFF display
TIMER ON display
SLEEP display
TEMP display
Air Purifying Filter
Emergency
Switch
Vertical blade
(adjust left and right air flow)
Display board
AUTO display
COOL display
Dry display
HEAT display
Remote controller
4. TIMER button
5. CLOCK button
6. HEALTH button
19
7. MODE button
8. HOUR button
9. SWING button
10. ON/OFF button
11. TIMER ON display
12. FAN SPEED display
LOW HI
MED AUTO
13. LOCK display
14. SWING UP/DOWN display
28
POWER/SOFT
1.CODE
Used to select CODE A or
B with a press, A or B will
be displayed on LCD.
Please select A without
special explanation.
2
RESET
.
button
When the remote
controller appears
abnormal, use a sharp
pointed article to press
this button to reset the
remote controller normal.
3.LIGHT button
Control the lightening and
extinguishing of
the indoor
LED display board.
The following functions and related displays are not
avai
lable:
20
26
15. SLEEP display
16. HEALTH display
17. Operation mode display
30
Operation mode
Remote controller
.Singal sending display
18
AUTO
COOL DRY
19. POWER/SOFT display
20. Left/right air flow display
21. TEMP display
22. TIMER OFF display
23. CLOCK display
24. TEMP button
25. FAN button
26. HEALTH AIRFLOW button
27. SLEEP button
28. SET button
29. POWER/SOFT button
30
LOCK
.
button
If pressed, the other buttons
will be disabled. Press it once
again,lock will be cancelled.
HEAT
FAN
Outdoor
OUTLET
INLET
Unit
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
or decrease 1min. If the
change quickly.
"AM "and "PM" stop flashing,while clock starts working.
After time setting is confirmed,press SET,
button is kept pressed,time will
2
will increase
POWER/SOFT
Loading of the battery
Remove the battery cover;
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
type fluorescent lamp or
room, the recei
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
ries have been used up.
batte
If the remote controller can't run normally during operation, please
remove the batteries and
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display
ver is apt to be disturbed in receiving
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with th
wireless telephone is installed in the
Please change batteries.
reload several minutes later.
after taking-out, just need to press reset key.
e" + "/"-";
the signals,
Operation
Base Operation
Remote controller
POWER/SOFT
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode
changes as follows:
Remote controller:
AUTO COOL DRY FAN HEAT
3.Select temp.setting
Press
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as
follows:
Remote controller:
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
Operation
Mode
AUTO
COOL
DRY
HEAT
FAN
button
Every time the button is pressed, temp.setting
increase 1
o
C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1
o
C,if kept depressed, it will decrease
rapidly
Display Board
nothing
LOW
MED
Remote
Controller
HI
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner
according to room
In DRY mode, when room temperature becomes
lower than temp.setting+2
at LOW speed regardless of FAN setting.
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.
AUTO
Note
When FAN is set to AUTO, the
automatically adjusts the fan speed
temperature.
o
C,unit will run intermittently
Emergency operation and test operation
Emergency Operation:
Use this operation only when the
remote controller is defective or lost.
When the emergency operation
switch is pressed, the" Pi "sound is
heard once, which means the start
of this operation.
In this operation, the system
automatically selects the operation modes, cooling or
fan or heat, according to the room temperature.
When machine is running in emergency, the set value
of temperature and wind speed couldn't be altered;
meanwhile, it can't operate for dehumidifying or under
timing mode.
Pi
Test operation:
Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room
temperature is below 16
normal operation.
o
C, do not use it in the
Pi Pi
Continue to press the test operation
switch for more than 5 seconds. After
you hear the "Pi" sound twice,
release
your finger from the switch: the cooling
operation starts with the air flow speed "Hi".
Air Flow Direction Adjustm
1.Status display of air sending
Vertical flap
Pos.1
Pos.4
2.Left and right air flow adjustment
Move the vertical blade by a knob on air
to adjust left and right direction referring to Fig.
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
at air outlet if all vertical louvers are
right.
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.
Note:
When restart after remote turning off, the remote
controller will automatically
set swing position.
Pos.2
Pos.5
Pos.3
Pos.6
(Auto swing)
(manual)
conditioner
adjusted to left or
mode ,
memorize the previous
3
Loading...