Haier HSU-24LEA03, HSU-24LEB03, HSU-24HEA03 User Manual
Installation Manual of Room Air Conditioner
Read this manual before installation
Explain sufficiently the operating means to the user
according to this ma
Necessary Tools for Installation
nual.
1.Driver
2.Hacksaw
3.Hole core drill
4.Spanner(17,19 and 26mm)
Accessory parts
No. Accessory parts
1
2
3
4
5
Remote controller
ry battery
R-03 d
Mounting plate
Drain hose
4X50
Steel nail, cement
Number
of
articles
1
2
1
1
6
5.
Torque wrench(17mm,22mm,26mm)
6.Pipe cutter
ring tool
7.Fla
fe
8.Kni
9.Nipper 12.Reamer
10.Gas leakage detector or
soap-and-
water solution
11.Measuring tape
Drawing for the installation of indoor and outdoor units
m
c
5
n
a
h
t
e
r
o
m
m
o
r
e
t
h
a
Optional parts for piping
Ma
rk
Parts name
A
Non-adhesi
Adhesi
B
Saddle(L.S) with scr
C
Connecting elect
D
for indoor and outdoor
E
F
Heating insulating mate
G
ve tape
Drain hose
Piping hole c
ve tape
ews
ric cable
rial
over
n
1
0
c
m
Attention must be paid to
the
rising up of drain hose
m
o
r
e
t
ah
n
01
c
m
A
6
7
8
10
Scr
4X25
ew
Plastic cap
Cover
Cushion
9
Pipe supporting plate
Drain-elbow
No.0010518785
4
1
4
1
Arrangement of piping directions
Rear left
Bel
Rear
right
Right
ow
Left
m
o
r
e
t
h
a
n
1
0
c
m
m
c
0
1
n
a
h
t
e
r
o
m
C
1
D
E
m
o
r
m
c
06
n
a
h
t
e
r
o
m
G
The marks from to in the figure are the parts numbers.
The distance bet
A
ween the indoor unit and the floor should be
more than 2m.
e
t
h
a
n
1
5
c
m
583
113.5
113.5
Floor fixing dimensions
of the outdoor unit
(Unit:mm)
184.3
0
8
3
6
113.5
.
4
3
3
184.3
Floor fixing dimensions
of the outdoor unit
(Unit:mm)
580
5
.
9
1
3
113.5
Floor fixing dimensions
of the outdoor unit
(Unit:mm)
633
HSU-24LEB03(T3)
PAS24L03-N(T3)
HSU-24HEA03(T3)
HSU-24LEA03(T3)
HSU-24HEA13(T3)
HSU-24LEA13(T3)
HSU-24LEA13-M
HSU-24LEA03
HSU-32LEA13-W
AMS30H03-N(T3)
HSU-24LEA03-T
HSU-30HEA13(T3)
HSU-30HEA03(T3)
PAS30H03-N(T3)
HSU-36LEA03(T3)
HSU-24HEA03
Selection of pipe
To this unit, both liquid and gas pipes shall be insulated
as they become Iow temperature in operation.
Use optional parts for piping set or pipes covered with
equivalent insulation material.
Indoor unit
1.Fitting of the Mounting Plate and Positioning of the wall Hole
When the mounting plate is first fixed
1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be
fixed against the wall, then temporarily fasten the plate with one steel nail.
2. Make sure once more the proper level of the plate, by hanging a thread with a weight from
the central top of the plate, then fasten securely the plate with the attachment steel nail.
3. Find the wall hole location A using a measuring tape
Liquid pipe ( )
Gas pipe ( )
9.52mm(3/8")
15.88mm(5/8")
B= 60mm
A=145mm
B= 60mm
mm03
HSU-24LEA03
HSU-24HEA03
HSU-24LEB03(T3)
HSU-24LEA13-M
A=145mm
mm03
2.Making a Hole on the Wall and Fitting the Piping Hole Cover
Make a hole of 60 mm in diamete
r,
slightly descending to outside the wall.
Install piping hole cover and seal it
off with putty after installation
Indoor side
Wall hole
60mm
Outdoor side
Thickness
of wall
(Section of wall hole)
2
G
Piping hole pipe
Loading...