Haier HSU-24HEA03/R2-I - annexe 1 Installation Manual

HSU-24HEA03/R2-I

INSTALLATION MANUAL

ROOM AIR CONDITIONER
WALL MOUNTED TYPE

NO.0010523237

Read this manual before installation

Explain sufficiently the operating means to the user

according to this manual.

1.Driver

2.Hacksaw

3.Hole core drill

4.Spanner(17,19 and 26mm)

5.

Torque wrench(17mm,22mm,26mm)

6.Pipe cutter

7.Fla

ring tool

8.Kni

fe

9.Nipper 12.Reamer

10.Gas leakage detector or
soap-and-

water solution

11.Measuring tape

A

B

C

D

E

F

G

Optional parts for piping

Ma

rk

Parts name

Non-adhesi

ve tape

Adhesi

ve tape

Saddle(L.S) with scr

ews

Connecting elect

ric cable

for indoor and outdoor

Drain hose

Heating insulating mate

rial

Piping hole c

over

Arrangement of piping directions

Rear left

Rear
right

Left

Bel

ow

Right

No. Accessory parts

Remote controller

R-03 d

ry battery

Mounting plate

Drain hose

Steel nail, cement

Scr

ew

Plastic cap

Cushion

1

1

2

3

4

5

6

7

8

9

2

1

1

6

4

1

4

1

Number
of
articles

Accessory parts

4X50

4X25

Pipe supporting plate

Drawing for the installation of indoor and outdoor units

Necessary Tools for Installation

10

Drain-elbow

1

The marks from to in the figure are the parts numbers.

The distance between the indoor unit and the floor should be
more than 2m.

A

G

Attention must be paid to
the

rising up of drain hose

m
c
5

na
h

t
e

r
o
m

m

c0

1n

a

h

t

e

r

o

m

m

c01

n

a

h

te

r

om

A

C

Guardring

10cmn

a

h

te

ro

m

10cm

n

a

h

t

e

r

o

m

60cm

n

a

h

te

r

om

15cm

n

a

h

t

e

ro

m

Fixing of outdoor unit

Indoor Unit

Selection of Installation Place

Power Source

Selection of pipe

Outdoor Unit

Fix the unit to concrete or block with bolts( 10mm) and nuts firmly and horizontally.

When fitting the unit to wall surface, roof or rooftop, fix a supporter surely with nails
or wires in consideration of earthquake and strong wind.

If vibration may a

ffect the house, fix the unit by attaching a vibration-proof mat.

Place, robust not causing vibration, where the body can be supported
su

fficiently.

Place, not a

ffected by heat or steam generated in the vicinity, where
inlet and outlet of the unit are not disturbed.
Place, possible to drain easil

y, where piping can be connected with the
outdoor unit.
Place, where cold air can be spread in a room entirel

y.
Place, nearby a power receptacle, with enough space around. (Refer
to drawings).
Place where the distance of more than lm from televisions, radios,
wireless apparatuses and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the
indoor unit can receive signals when the fluorescent lamps in the room
are lightened.

Place, which is less a

ffected by rain or direct sunlight and is

su

fficiently ventilated.
Place, possible to bear the unit, where vibration and noise are
not increased.
Place, where discharged wind and noise do not cause a
nuisance to the neighbors.
Place, where a distance marked is available as illustrated
in the above figure.

Before inserting power plug into receptacle, check the voltage without fail. The power source is the same as the corresponding name plate.

Install an exclusive branch circuit of the powe

r.

A receptacle shall be set up in a distance where the power cable can be reached. Do not extend the cable by cutting it.

To this unit, both liquid and gas pipes shall be insulated

as they become Iow temperature in operation.

Use optional parts for piping set or pipes covered with

equivalent insulation material.

2

Liquid pipe ( )

Gas pipe ( )

9.52mm(3/8")

15.88mm(5/8")

For 24K

184

580

184

8

0
3

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

Indoor unit

1.Fitting of the Mounting Plate and Positioning of the wall Hole

2.Making a Hole on the Wall and Fitting the Piping Hole Cover

When the mounting plate is first fixed

When the mounting plate is fixed side bar and lintel

1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be
fixed against the wall, then temporarily fasten the plate with one steel nail.

2. Make sure once more the proper level of the plate, by hanging a thread with a weight from
the central top of the plate, then fasten securely the plate with the attachment steel nail.

3. Find the wall hole location A using a measuring tape

Refer to the previous article, " When the mounting plate is first fixed ", for the
position of wall hole.

Fix to side bar and lintel a mounting ba

r, Which is separately sold, and then fasten

the plate to the fixed mounting bar.

Make a hole of 83 mm in diameter,
slightly descending to outside the wall.
Install piping hole cover and seal it
off with putty after installation

(Section of wall hole)

Piping hole pipe

Outdoor side

Thickness
of wall

Indoor side

Wall hole

83mm

3.Installation of the Indoor Unit

Drawing of pipe

[ Rear piping ]

Draw pipes and the drain hose, then fasten them with the adhesive tape

[ Left Left-rear piping ]

In case of left side piping, cut away, with a nipper, the lid for left piping.
In case of left-rear piping, bend the pipes according to the piping direction to the mark of hole for left-rear
piping which is marked on heat insulation materials.

3

G

A=145mm

B= 83mm

mm03

Indoor unit

Fixing the indoor unit body

[Other direction piping]

Indoor/outdoor electric cable and drain hose must be bound with refrigerant piping by protecting tape.

Cut away, with a nipper, the lid for piping according to the piping direction and then bend the pipe according
to the position of wall hole. When bending, be careful not to crash pipes.
Connect beforehand the indoor/outdoor electric cable, and then pull out the connected to the heat insulation
of connecting part specially.

Hang surely the unit body onto the upper notches of the
mounting plate. Move the body from side to side to verify
its secure fixing.
In order to fix the body onto the mounting plate,hold up
the body aslant from the underside and then put it down
perpendicularly.

1. Insert the drain hose into the dent of heat insulation materials of indoor unit.

2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it out on the front side, then
connect them.

3. Coat the flaring seal face with refrigerant oil and connect pipes.
Cover the connection part with heat insulation materials closely, and make sure fixing with adhesive tape

4

Heat insulation
material

Drain hose

Piping

Indoor/outdoor
electric cable

Lid for right piping

Lid for under piping

Lid for left piping

Fix with adhesive tape

Easily-demount cleaning of indoor unit

Inlet grille can be taken down

mounting plate

Open the inlet grille,press the button of unlock in the left,then push
it out of the socket and take out the inlet grille.

Unloading of indoor unit body

When you unload the indoor unit,please use your hand to arise

the body to leave agraffe,then lift the bottom of the body outward

slightly and lift the unit aslant until it leaves the mounting plate.

mounting plate

agraffe