Haier HSU-24HEA13, HSU-24HEA03, HSU-24LEA13, HSU-24LEA03, HSU-30HEA03 User Manual

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

HSU-24HEA03(T3)
HSU-24LEA03(T3)

HSU-24HEA13(T3)
HSU-24LEA13(T3)

HSU-30HEA13(T3)
HSU-30HEA03(T3)

Please read this operation manual before using the air conditioner.

0010518784

Before disposing an old air conditioner that
goes out of use, please make sure it's inop­erative and safe. Unplug the air conditioner
in order to avoid the risk of child entrapment.

It must be noticed that air conditioner system
contains refrigerants, which require speciali­zed waste disposal. The valuable materials
contained in an air conditioner can be recycled
.Contact your local waste disposal center for
proper disposal of an old air conditioner and
contact your local authority or your dealer if
you have any question. Please ensure that
the pipework of your air conditioner does not
get damagedprior to being picked up by the
relevant waste disposal center, and contribute
to environmental awareness by insisting on an
appropriate, anti-pollution method of disposal.

Cautions

Disposal of the old air conditioner

All the packaging materials employed in the
package of your new air conditioner may be
disposed without any danger to the
environment.

The cardboard box may be broken or cut into
smaller pieces and given to a waste paper
disposal service. The wrapping bag made of
polyethylene and the polyethylene foam pads

contain no fluorochloric hydrocarbon.

All these valuable materials may be taken to
a waste collecting center and used again after
adequate recycling.

Consult your local authorities for the name
and address of the waste materials collecting
centers and waste paper disposal services
nearest to your house.

Disposal of the packaging of your
new air conditioner

Before starting the air conditioner, read the
information given in the User's Guide caref­ully. The User's Guide contains very impor­tant observations relating to the assembly,
operation and maintenance of the air
conditioner.

The manufacturer does not accept respon­sibility for any damages that may arise due
to non-observation of the following
instruction.

Damaged air conditioners are not to be
put into operation. In case of doubt, consult
your supplier.

Use of the air conditioner is to be carried
out in strict compliance with the relative
instructions set forth in the User's Guide.

Installation shall be done by professional
people, don't install unit by yourself.

For the purpose of the safety,the air con­ditioner must be properly grounded in acco­rdance with specifications.

Always remember to unplug the air
conditioner before openning inlet grill. Never
unplug your air conditioner by pulling on
the power cord. Always grip plug firmly and
pull straight out from the outlet.

All electrical repairs must be carried out
by qualified electricians. Inadequate repairs
may result in a major source of danger for
the user of the air conditioner.

Safety Instructions and Warnings

Do not damage any parts of the air
conditioner that carry refrigerant by piercing
or performating the air conditioner's tubes
with sharp or pointed items, crushing or
twisting any tubes, or scraping the coatings
off the surfaces. If the refrigerant spurts
out and gets into eyes, it may result in
serious eye injuries.

1

3. If the fuse of indoor unit on PC board is
broken,please change it with the type of

T. 3.15A/ 250V.

Do not obstruct or cover the ventilation
grille of the air conditoner.Do not put fingers
or any other things into the inlet/outlet and
swing louver.

Do not allow children to play with the air
conditioner.In no case should children be
allowed to sit on the outdoor unit.

The refrigerating circuit is leak-proof.

1.Applicable ambient temperature range:

Specifications

The machine is adaptive in following
situation

10 .The power plug and connecting cable

must have acquired the local attestation.

2. If the power supply cord is damaged, it
must be replaced by the manufacturer

or its service agent or a similar qualified
person.

4. The wiring method should be in line with
the local wiring standard.

5. After installation, the power plug should
be easily reached.

6. The waste battery should be disposed
properly.

7. The appliance is not intended for use
by young children or infirm persons

without supervision.

8. Young children should be supervised
to ensure that they do not play with
the applience.

9.Please employ the proper power plug,

which fit into the power supply cord.

Cautions

11.In order to protect the units,please turn

off the A/C first, and at least 30 seconds
later, cutting off the power.

2

For: 220-240V~, 50Hz

For: 220V~, 60Hz

Cooling

Indoor

Maximum:D.B/W.B

32

o

C/23oC

52

o

C/31oC

18

o

C

18

o

C/14oC

Maximum:D.B/W.B
Minimum:D.B

Minimum:D.B/W.B

Outdoor

Indoor

Outdoor

Maximum:D.B
Minimum:

D.B/W.B

Maximum:

D.B

Minimum:D.B

27

o

C

27

o

C/18oC

15

o

C

-7

o

C

Heating

Cooling

Heating

Indoor

Outdoor

Indoor

Outdoor

Maximum: D.B / W.B
Minimum: D.B / W.B

Maximum: D.B / W.B
Minimum: D.B

Maximum: D.B
Minimum: D.B

Maximum: D.B / W.B
Minimum: D.B / W.B

29oC/19oC
18

o

C/14oC

54oC/24oC
18oC

27oC
15oC

24oC/18oC

-7

o

C/-8oC

Cautions

STRICT
ENFORCEMENT

Safety Instruction

Installation

WARNING

Please read the following Safety Instructions carefully prior to use.

The instructions are classified into two levels, WARNING and CAUTION according to
the seriousness of possible risks and damages as follows. Compliance to the
instructions are strictly required for safety use.

Please call Sales/Service Shop for the Installation.

Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.

lnstallation in a inadequate place may cause accidents. Do not install in the following place.

Connect the earth
cable.

earthing

Do not install in the
place where there is
any possibility of
inflammable gas
leakage around the
unit.

Do not get the unit
exposed to vapor
or oil steam.

Check proper
installation of the
drainage securely

PROHIBITION PROHIBITION

CAUTION

3

Cautions

WARNING

When abnormality such as burnt-small found,
immediately stop the operation button and
contact sales shop.

OFF

Use an exclusive power source with a
circuit breaker

ENFORCEMENT

Connect power supply cord
to the outlet completely

Use the proper voltage

Do not use power supply cord
in a bundle.

Take care not to damage

the power supply cord.

Do not use power supply cord

extended or connected in halfway

STRICT

ENFORCEMENT

STRICT

STRICT

ENFORCEMENT

PROHIBITION

PROHIBITION

PROHIBITION

PROHIBITION

Do not start or stop the
operation by disconnecting
the power supply cord and so on.

Do not channel the air flow directly
at people, especially at infants or
the aged.

Do not try to repair or reconstruct
by yourself.

Do not use for the purpose of storage of
food, art work, precise equipment,
breeding, or cultivation.

CAUTION

Take fresh air occasionally especially
when gas appliance is running at the
same time.

PROHIBITION

STRICT

ENFORCEMENT

Do not operate the switch with
wet hand.

PROHIBITION

PROHIBITION

PROHIBITION

PROHIBITION

PROHIBITION

Do not install the unit near a fireplace
or other heating apparatus.

Check good condition of the
installation stand

Do not pour water onto the unit
for cleaning

PROHIBITION

Do not place animals or plants in
the direct path of the air flow

Do not place any objects on or
climb on the unit.

Do not place flower vase or water
containers on the top of the unit.

Do not insert objects into the air
inlet or outlet.

PROHIBITION

PROHIBITION

PROHIBITION

4

Parts and Functions

5

Indoor Unit

Outlet

Inlet

Inlet

grille

Anion gene

(inside)

Vertical blade(inside)

(adjust left and

Note:The inlet grill will not be risen automat
grill upward.

rator

right air flow)

Outdoor Unit

Air filter(inside)

display board(inside)

Horizontal flap
(adjust up and d
Don't adjust it manually)

Power plug

ically,when the unit is placed with the inlet

own air flow

4

HSU-24HEA03(T3)
HSU-24LEA03(T3)
HSU-24HEA13(T3)
HSU-24LEA13(T3)

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

HSU-30HEA13(T3)
HSU-30HEA03(T3)

4

Parts and Functions

Display board

19

POWER/SOFT

28

30

1.CODE

Used to select CODE A or B with a press,A or B
will be displayed on LCD.
Please select A without special explanation.

2.RESET

When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.

3.LIGHT button

Control the lightening and extinguishing of
the indoor LED display board.

4. TIMER button

Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF.

5. CLOCK button

Used to set correct time.

6. HEALTH button

Used to set healthy operation.

7. MODE button

AUTO COOL DRY FAN HEAT

8. HOUR button

Used to set clock and timer setting.

9. SWING button

Used to select up or down air sending direction.

10. ON/OFF button

Used for unit start and stop.

31

11

. TIMER ON display

12

. FAN SPEED display

11

15

16

LOW HI

MED AUTO

23

21

13. LOCK display
. SWING UP/DOWN display

14

. SLEEP display

15
16

. HEALTH display

17. Operation mode display

AUTO

Operation mode

Remote controller

Display board

COOL DRY

18.Singal sending display
19

. POWER/SOFT display
. Left/right air flow display

20

21. TEMP display

Remote controller: to display the TEMP. setting.

. TIMER OFF display

22

. CLOCK display

23

. TEMP button

24

Used to select your desired temperature.

25. FAN button

Used to select fan speed: LOW,MED, HI, AUTO.

26. HEALTH AIRFLOW button

Used to set the health airflow mode.

27

. SLEEP button

Used to select sleep mode.

28. SET button

Used to confirm timer and clock settings.

29. POWER/SOFT button

Use to set power/soft function.

30. LOCK

Used to lock buttons and LCD display. If pressed, the
other buttons will be disabled and the lock condition
display appears. Press it once again, lock will be
cancelled and lock condition display disappears.

31.

Remote signal receiver

HEAT

17

FAN

NOTE: The following functions and related displays are not available: 20

Cooling only unit do not have displays and functions related with heating

6

Parts and Functions

Clock Set

When unit is started for the first time and after replacing batteries in
remote controller, clock should be adjusted as follows:

1. Press CLOCK button,"AM" or "PM" flashes.

2. Press or to set correct time. Each press will increase or decrease
1 min. If the button is kept depressed, time will change quickly.

3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing,
while clock starts working.

Remote controller's operation

When in use, put the signal transmission head directly to the receiver hole on the indoor unit.
The distance between the signal transmission head and the receiver hole should be within
7m without any obstacle as well.

Don't throw or knock the remoter controller.
When electronic-started type fluorescent lamp or change-over type fluorescent lamp or

wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving
the signals, so the distance to the indoor unit should be shorter.

Loading of the battery

Load the batteries as illustrated right
2 R-03 (7#) batteries

Remove the battery cover:

Slightly press" "area and push down the cover
as illustrated.

Load the battery:
Be sure that the loading is in line with the "+" / "-".

request as illustrated on the bottom of the case.
Put on the cover again.

POWER/SOFT

Confirmation indicator:
After pressing power ON/OFF, if no display, reload the batteries.

Note:

Full display or unclear display during operation indicates the batteries have been used up.
Please change batteries.

Used two new same-typed batteries when loading.
If the remote controller can't run normally during operation, please remove the batteries and

reload several minutes later.

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.

Remove the batteries in case unit won't be in usage for a long period. If there are any display
after taking-out, just need to press reset key.

7