Haier HSU-24H03/Z - annexe 1 User Manual

No.0010504735

HSU-24H03/Z

Maximum: D.B

10.The appliance must be installed on strong enough supporter.

9.Young children should be supervised ensure that they do not play with the appliance.

8. The appliance is not intended to use by young children or infirm persons without supervision.

7. The waste battery should be disposed properly.

6. After installation, the power plug should be easily reached.

5. The wiring method should be in line with the local wiring standard.

4. The distance between the indoor unit and the floor should be more than 2m.

3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.

11.The wiring diagram is attached inside the machine.

or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent

Cautions

The machine is adaptive in following situation

I. Applicable ambient temperature range:

Cooling

Heating

Indoor

Outdoor

Outdoor

Indoor

Maximum: D.B / W.B 32oC/23oC

18oC/14oC
43oC/26oC

18oC
27oC

15oC
24oC/18oC

-7oC/-8oC

Minimum: D.B / W.B

Minimum: D.B
Maximum: D.B

Minimum: D.B
Maximum: D.B / W.B
Minimum: D.B / W.B

1

Parts and Functions

Signal Receiving windows
Running Indicator

Timer Mode Indicator
Power Indicator

2

FAN

DRY
HEAT

COOL

AUTO

Parts and Functions

Operation

1. Mode display

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF

Used for unit start and stop.

12. MODE

Used to select AUTO run, COOL,
DRY, HEAT and FAN operation

13. FAN

Used to select fan speed LO, MED, HI, AUTO

14. HOUR

Used to set clock and timer setting.

15. SWING

Used to set auto fan direction.

16. SLEEP

Used to select sleep mode.

17. LOCK

Used to lock buttons and LCD
display.

18. TEMP.

Used to select your desired temp.

19. SET

Used to confirm timer and clock settings.

20. TIMER

Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF

21. CLOCK

Used to set correct time

22. RESET

normal condition.

Used to reset the controller back to

Clock set

When unit is started for the first time and after replacing batteries in remote controller,
clock should be adjusted as follows:
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will increase or decrease 1min. If the
button is kept depressed, time will change quickly.
After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock
starts working.

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.

NOTE: Cooling only unit do not have displays and functions related with heating

Buttons and display of the remote controller.

LO MED HIAUTO

ON/OFF

TEMP

MODE SET

FAN

TIMER

SWING

CLOCK

SLEEP

LOCK RESET

5
6

7

8

9

10

18
19

20

21

22

4

1

2
3

11

12

13
14

15

16

17

A
U
T
O

ON OFF

AM
PM

o

C

3

AUTO

LO

MED

HI

Parts and Functions

Operation

Buttons and display of the remote controller.

like the following figure:

If the unit which you purchased has healthy function, Remote controller should

BRIEF INTRODUCTION TO HEALTH OPERATION

The anion generator in the air conditioner can generate a lot of anion to
effectively balance the quantity of position and anion in the air and also to kill
bacteria and speed up the dust sediment in the room and finally clean the air
in the room.

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF
Used for unit start and stop.

12. MODE
Used to select AUTO run, COOL,
DRY, HEAT and FAN operation

13. FAN
Used to select fan speed LO, MED, HI, AUTO

14. HOUR
Used to set clock and timer setting.

15. SWING
Used to set auto fan direction.

16. SLEEP
Used to select sleep mode.

17. LOCK
Used to lock buttons and LCD
display.

18. TEMP.
Used to select your desired temp.

19. SET
Used to confirm timer and clock settings.

20. TIMER
Used to select TIMER ON, TIMER OFF,

TIMER ON-OFF

21. CLOCK
Used to set correct time

22. RESET

Used to reset the controller back to
normal condition.

23. HEALTH

1. Mode display

AUTO

COOL

DRY

HEAT

FAN

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

Used to set healthy operation

NOTE: Cooling only unit do not have displays and functions related with heating

HEALTH

ON/OFF TEMP

MODE SET

FAN TIMER

SWING CLOCK

SLEEP

LOCK RESET

4

1

2
3

11

12

13
14

15

16

17

5
6

7
8
9

10

19

21

22

18

20

A
U
T
O

ON

OFF

AM
PM

o

C

4

ÇëÑ¡ÓÃͬһƷÅÆÁ½½Ú
7#
µç³Ø,³¤Ê±¼ä²»ÓÃʱ,Ϊ

·АЦ¹В©Т¹Зл½«µз³ШИ¡
³ц¡£
ФЪК¹УГЦРИзУцТм³£,Зл
½«µз³ШИ¡³ц,6·ЦЦУºуФЩ
Ч°ИлРВµз³Ш¡£

º£¶ы¼¯НЕЗаµºº£¶ы
¿ХµчЖчУРПЮЧЬ¹«Л¾

ÇëÑ¡ÓÃͬһƷÅÆÁ½½Ú
7#
µç³Ø,³¤Ê±¼ä²»ÓÃʱ,Ϊ

·АЦ¹В©Т¹Зл½«µз³ШИ¡
³ц¡£
ФЪК¹УГЦРИзУцТм³£,Зл
½«µз³ШИ¡³ц,6·ЦЦУºуФЩ
Ч°ИлРВµз³Ш¡£

º£¶ы¼¯НЕЗаµºº£¶ы
¿ХµчЖчУРПЮЧЬ¹«Л¾

ÇëÑ¡ÓÃͬһƷÅÆÁ½½Ú
7#

µç³Ø,³¤Ê±¼ä²»ÓÃʱ,Ϊ

·АЦ¹В©Т¹Зл½«µз³ШИ¡
³ц¡£
ФЪК¹УГЦРИзУцТм³£,Зл
½«µз³ШИ¡³ц,6·ЦЦУºуФЩ

×°Èëеç³Ø¡£

º£¶ы¼¯НЕЗаµºº£¶ы
¿ХµчЖчУРПЮЧЬ¹«Л¾

Operation

Remote controller's operation

When in use, put the signal transmission head directly to the
receiver hole on the indoor unit.

The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.

Don't throw the controller, prevent it from being damaged.
When electronic-started type fluorescent lamp or change-over

type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receivering the signals
so the distance to the indoor unit should be shorter.

Loading of the battery

Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder)

Remove the battery cover:

Slightly press " " and push down the cover.

Load the battery:

Be sure that the loading is in line with the" + "/"-"
pole request as illustrated.

Put on the cover again
Confirmation indicator:

In disorderation, reload the batteries or load the new batteries after 6mins.

Note:

Use two new same-typed batteries when loading.
If the remote controller can't run normally or doesn't work at all,
use a sharp pointed item to press the reset key.

Hint:

Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out just need to press reset key.

Power failure resume(please set and apply as necessary)

If sudden power failure occurs, the unit will resume original operation when power is
supplied again.

Note:

When sudden power failure happens during unit operation in power failure resume mode, if
the air conditioner is not desired for use in a long period, please shut off the power supply
in case that the unit automatically resume operation when power is re-supplied, or press
ON/OFF to turn off the unit when power resumes.

5

(4) Unit stop

(1) Unit start

Auto run, Fan operation

Enjoy yourself by just a gentle press.

Operation

mode changes as follows:

Press ON/OFF button, unit starts.
Previous operation status appears on display.
(Not Timer setting)
Power indicator on indoor unit lights up.

(2) Select operation mode

Press MODE button. For each press, operation

AUTO COOL DRY HEAT FAN

Unit will run in selected mode.
Stop display at " " AUTO or " "FAN.

(3) FAN

Press FAN button. For each press, fan speed changes
as follows:

AUTO LO MED HI

Unit will run at selected fan speed.
Note:AUTO is not available in FAN mode.

Press ON/OFF button.
Only time remains on LCD.
All indicators on indoor unit go out.
Vertical flap closed automatically.

Hints

Remote controller can memorize settings in each operation mode. To run it next time just
select the operation mode and it will start with the previous setting.
No reelecting is needed.(TIMER ON/OFF needs reelecting)

Cautions: Note:
On cooling only unit, heating mode is not available, The above information is the

After replacing batteries, press ON/OFF, and display explanation of the displayed
becomes as follows: information therefore varies
Operation mode: AUTO, Temp. No with those displayed in actual
Timer mode: No, Fan speed :AUTO operation.

ON/OFF TEMP

SET

TIMER

CLOCKSWING

SLEEP

LOCK

RESET

FAN

MODE

1

2

3

4

6

Press MODE button. For each press, operation

Recommendations:

Operation

COOL,HEAT and DRY operation

Use COOL in summer. Use HEAT in winter
Use DRY in spring, autumn and in damp climate.

(1) Unit start

mode changes as follows:

Press ON/OFF button, unit starts.
Previous operation status appears on display.(Not Timer setting)
Power indicator on indoor unit lights up.

(2) Select operation mode

AUTO COOL DRY HEAT FAN

Unit will run in operation mode displayed on LCD.
Stop display at your desired mode.

(3) Select temp. setting

Press TEMR button.

Every time the button is pressed, temp. setting increases 1oC
Every time the button is pressed, temp. setting decreases 1oC

Unit will start running to reach the temp. setting on LCD.

Press FAN button. For each press, fan speed changes

(4) Fan speed selection

as follows:

AUTO LO MED HI

just press ON/OFF button and unit will run in previous status.

Unit runs at the speed displayed on LCD.
In DRY mode, when room temp. becomes 2oC higher than
temp. setting, unit will run intermittently at LO speed
regardless of FAN setting.

Hints

On cooling only unit, heating mode is not available.
Remote controller can memorize each operation status. When starting it next time,

COOL operation starts when room
temp. is higher than temp. setting.

Ultra-low air flow

Temp. setting+2oC

Temp. setting

On reaching temp. setting, unit
will run in mild DRY mode.

ON/OFF TEMP

SET

TIMER

CLOCKSWING

SLEEP

LOCK

RESET

FAN

MODE

1

2

3

4

3

5

6

7

Operation

(5) Air flow direction adjustment

After operation mode is selected, vertical flap will open automatically according to the mode.
Referring to the Fig.

COOL

HEAT

COOL

HEAT

About 10

o

About 10

o

better set a temp. difference of 3-5oC between indoor and outdoor temp. in COOL mode.

Hints

As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more
helpful for a better air circulation.
As warm air flows upward in HEAT mode, adjusting air flow downward will be much more
helpful for a better air circulation.
Be careful not to catch a cold when cold air blows downward.
It is harmful to your health in summer to go frequently in and out of places where temp.
difference is above 7oC. Temp. difference of 3-5oC will remove your fatigue.
More than this, unit's load can be reduced and power consumption cut down as well. So, you'd

(6) Unit stop

Press ON/OFF button.
Only time remains on LCD.
Vertical flap closes automatically.

Cautions:

Unit won't restart until 3 minutes have
elapsed, due to system protection.
HEAT mode is not available on
cooling only unit.

It is advisable not to keep vertical flap at
downward position for a long time in COOL
or DRY mode, otherwise, condensate
water might occur.

Cautions:

Cautions:

When humidity is high, condensate water
might occur at air outlet if all horizontal
louvers are adjusted to left or right.

Move the horizontal blade by a knob on air
conditioner to adjust left and right direction
referring to Fig.

Left and right air flow adjustment
(manual)

Press SWING button, vertical flap will move within
the range shown in the Fig. Press SWING button
stop it at a fixed position.

Up and down (Use remote controller)

About 45

o

About 60

o

About 60

o

8

Operation

TIMER Operation

You can let unit start or stop automatically at following times: Before you wake up in the
morning, or get back from outside or after you fall asleep at night.

Set Clock correctly before starting Timer operation

TIMER ON/OFF

Power indicator on indoor unit lights up.

(1)After unit start, select your desired operation mode.
Operation mode will be displayed on LCD.

(2)TIMER mode selection

Press TIMER button to change TIMER mode.
Every time the button is pressed, display changes as follows:

ON OFF ON OFF

TIMER ON TIMER OFF TIMER ON-OFF

blank

Select your desired TIMER mode (TIMER ON or TIMER
OFF) ON or OFF will flash.

(3)Timer setting

Press HOUR / button.

Every time the button is pressed, time increases 10 min.

If button is kept depressed, time will change quickly.

Every time the button is pressed, time decreases 10 min.
If button is kept depressed, time will change quickly. Time
will be shown on LCD. It can be adjusted within 24 hours.

Timer mode indicator on indoor unit lights up.

(4)Confirming your setting

After setting correct time, press SET button to confirm, "ON"
or "OFF" stops flashing
Time displayed: Unit starts or stops at x hour x min. (TIMER
ON or TIMER OFF).

To cancel TIMER mode

Just press TIMER button several times until TIMER mode disappears.

Hints

After replacing batteries or a power failure happens, Time setting should be reset.

Remote controller possesses memory function, when use TIMER mode next time, just

press SET button after mode selecting if timer setting is the same as previous one.

ON/OFF TEMP

SET

TIMER

CLOCKSWING

SLEEP

LOCK

RESET

FAN

MODE

ON

1

2

3

4

3

9