Haier HSU-24C03/Z - annexe 2, HSU-24C03/Z 2 Operation Manual

No.0010554541

Please read this operation manual before using the air conditioner.

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

1
2-4

5-12
13-17

18

Contents

Cautions
Parts and functions
Operation

Maintenance
Trouble shooting

Maximum: D.B

1

10.The appliance must be installed on strong enough supporter.

9.Young children should be supervised ensure that they do not play with the appliance.

8. The appliance is not intended to use by young children or infirm persons without supervision.

7. The waste battery should be disposed properly.

6. After installation, the power plug should be easily reached.

5. The wiring method should be in line with the local wiring standard.

4. The distance between the indoor unit and the floor should be more than 2m.

3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.

11.The wiring diagram is attached inside the machine.

or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent

Cautions

The machine is adaptive in following situation

I. Applicable ambient temperature range:

Cooling

Heating

Indoor

Outdoor

Outdoor

Indoor

Maximum: D.B / W.B 32oC/23oC

18oC/14oC
43oC/26oC

18oC
27oC

15oC
24oC/18oC

-7oC/-8oC

Minimum: D.B / W.B

Minimum: D.B
Maximum: D.B

Minimum: D.B
Maximum: D.B / W.B
Minimum: D.B / W.B

2

Parts and Functions

Signal Receiving windows
Running Indicator

Timer Mode Indicator
Power Indicator

FAN

DRY
HEAT

COOL

AUTO

3

Parts and Functions

Operation

1. Mode display

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF

Used for unit start and stop.

12. MODE

Used to select AUTO run, COOL,
DRY, HEAT and FAN operation

13. FAN

Used to select fan speed LO, MED, HI, AUTO

14. HOUR

Used to set clock and timer setting.

15. SWING

Used to set auto fan direction.

16. SLEEP

Used to select sleep mode.

17. LOCK

Used to lock buttons and LCD
display.

18. TEMP.

Used to select your desired temp.

19. SET

Used to confirm timer and clock settings.

20. TIMER

Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF

21. CLOCK

Used to set correct time

22. RESET

normal condition.

Used to reset the controller back to

Clock set

When unit is started for the first time and after replacing batteries in remote controller,
clock should be adjusted as follows:
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will increase or decrease 1min. If the
button is kept depressed, time will change quickly.
After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock
starts working.

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.

NOTE: Cooling only unit do not have displays and functions related with heating

Buttons and display of the remote controller.

LO MED HIAUTO

ON/OFF

TEMP

MODE SET

FAN

TIMER

SWING

CLOCK

SLEEP

LOCK RESET

5
6

7

8

9

10

18
19

20

21

22

4

1

2
3

11

12

13
14

15

16

17

4

AUTO

LO

MED

HI

Parts and Functions

Operation

Buttons and display of the remote controller.

like the following figure:

If the unit which you purchased has healthy function, Remote controller should

BRIEF INTRODUCTION TO HEALTH OPERATION

The anion generator in the air conditioner can generate a lot of anion to
effectively balance the quantity of position and anion in the air and also to kill
bacteria and speed up the dust sediment in the room and finally clean the air
in the room.

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF
Used for unit start and stop.

12. MODE
Used to select AUTO run, COOL,
DRY, HEAT and FAN operation

13. FAN
Used to select fan speed LO, MED, HI, AUTO

14. HOUR
Used to set clock and timer setting.

15. SWING
Used to set auto fan direction.

16. SLEEP
Used to select sleep mode.

17. LOCK
Used to lock buttons and LCD
display.

18. TEMP.
Used to select your desired temp.

19. SET
Used to confirm timer and clock settings.

20. TIMER
Used to select TIMER ON, TIMER OFF,

TIMER ON-OFF

21. CLOCK
Used to set correct time

22. RESET

Used to reset the controller back to
normal condition.

23. HEALTH

1. Mode display

AUTO

COOL

DRY

HEAT

FAN

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

Used to set healthy operation

NOTE: Cooling only unit do not have displays and functions related with heating

HEALTH

ON/OFF TEMP

MODE SET

FAN TIMER

SWING CLOCK

SLEEP

LOCK RESET

4

1

2
3

11

12

13
14

15

16

17

5
6

7

8

9

10

19

21

22

18

20